NXP Semiconductors

MC9S08PB16MTJ - 8-Bit 20MHz 16KB Flash MCU | NXP

MPN: MC9S08PB16MTJ ✓ Active
2.7 V to 5.5 V Vdss 20-pin TSSOP Package 20 MHz Speed 16 KB Memory
MOQ: 1 |

MC9S08PB16MTJ Overview

NXP Semiconductors MC9S08PB16MTJ is an 8-bit S08P microcontroller with a 20 MHz CPU, 16 KB of Flash memory, 1 KB of RAM, and a 20-pin TSSOP package. It operates from 2.7 V to 5.5 V and is specified for temperatures from -40°C to +125°C. The device combines an 8-bit S08 central processor with a 12-bit ADC, analog comparator, amplifier, I2C interface, and flexible timer resources for compact embedded control designs.

An 8-bit microcontroller is a semiconductor that executes firmware from embedded program memory while reading inputs and controlling outputs in a dedicated control system. The S08P belongs to the MCU hierarchy, where microcontrollers integrate a CPU, memory, peripherals, and communication interfaces into one device. The MC9S08PB16MTJ is suited to applications that require deterministic low-cost control without the memory or processing demands of a 32-bit MCU.

Key features include a maximum 20 MHz bus, 16 KB Flash for program storage, and 1 KB of RAM. The analog subsystem provides a 12-bit ADC plus comparator and amplifier functions, reducing the need for separate analog components. Up to 30 interrupt and reset sources, four levels of nested interrupts, an I2C interface, and flexible timers support responsive control and connected peripherals while preserving board space.

The S08 architecture reuses the established S08 core, intellectual property, and development tools, easing migration within the S08P family. Its 2.7 V to 5.5 V operating range supports both 3.3 V and 5 V system rails. The extended -40°C to +125°C temperature qualification makes it suitable for industrial environments where temperature variation and long service intervals must be considered.

Typical uses include industrial sensor controllers, motor and valve control, appliance interfaces, building equipment, low-cost instrumentation, and compact analog-monitoring products. The MCU can sample an analog input through its ADC, coordinate peripherals over I2C, and manage timing or actuator functions through its timer blocks without requiring a separate analog controller.

Designers should use the NXP datasheet pin-description table when assigning PCB signals and should preserve the package power and decoupling requirements. Pay particular attention to analog-input routing, I2C pull-up placement, and programming or debugging access. A common migration rule is to confirm that the alternative MCU has the same 20-pin TSSOP footprint and matching peripheral assignments before replacing this device.

This product page consolidates the key electrical, memory, analog, packaging, and environmental characteristics of the MC9S08PB16MTJ with pin-compatible S08P migration options, practical PCB guidance, and a parameter-by-parameter replacement table.

Drop-in alternatives for MC9S08PB16MTJ — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

Variants in this series

Same-series models that are drop-in compatible with MC9S08PB16MTJ (same form factor and footprint) — differing in ADC Resolution, CPU Architecture, Operating Temperature Range, Program Memory Organization.

NXP Semiconductors
ADC Resolution: 12-bit
CPU Architecture: 8-bit
Operating Temperature Range: -40 C to +125 C
Compare with MC9S08PB16MTJ →

MC9S08PB8MTJ

✅ Drop-In ⚠️ Specs Unverified
NXP Semiconductors
📦 20-TSSOP
8-bit S08 microcontroller · 8-bit · 20 MHz · 8 KB · 8K x 8 · 5 V · 12-bit · Integrated

Contact for price

View Datasheet →

MC9S08PB8MTL

✅ Drop-In ⚠️ Specs Unverified
📦 20-TSSOP
Flash memory is 8 KB instead of 16 KB and the temperature grade differs; the 20-pin TSSOP footprint and core remain compatible.

📋 Reference alternative (not in catalog)

MC9S08PB16MTL

✅ Drop-In ⚠️ Specs Unverified
📦 20-TSSOP
Memory and core ratings match, while the temperature grade differs from the MC9S08PB16MTJ.

📋 Reference alternative (not in catalog)

MC9S08PB8MJB

✅ Drop-In ⚠️ Specs Unverified
📦 20-TSSOP
Flash memory is 8 KB instead of 16 KB, a 50% reduction, with a different temperature qualification code.

📋 Reference alternative (not in catalog)

MC9S08PB16MJB

✅ Drop-In ⚠️ Specs Unverified
📦 20-TSSOP
Core, memory, and voltage ratings match; the suffix identifies a different temperature qualification code.

📋 Reference alternative (not in catalog)

MC9S08PB16MTJ Maximum Ratings & Electrical Characteristics

CPU Architecture 8-bit S08 central processor unit
Maximum CPU Frequency 20 MHz
Operating Voltage Range 2.7 V to 5.5 V
Flash Memory 16 KB
Program Memory Organization 16K x 8 bits
RAM 1 KB
ADC Resolution 12 bits
Analog Functions ADC, analog comparator, and amplifier
Serial Interface I2C
Timer Resources Flexible timers
Interrupt and Reset Sources Up to 30 sources
Nested Interrupt Levels Up to 4 levels
Operating Temperature Range -40°C to +125°C
Package 20-pin TSSOP
Mounting Type Surface mount
Shipping Package Tube
Nominal Supply Voltage 5 V
ESD and EFT Performance Enhanced EFT/ESD performance

MC9S08PB16MTJ tube Pin Configuration Guide

Pin configuration for MC9S08PB16MTJ (tube package). This digital IC includes GPIO, communication interfaces (UART, SPI, I2C), and power pins. Refer to the manufacturer datasheet for alternate pin functions and configuration options. Essential for embedded system design and PCB layout.

tube package pinout diagram for MC9S08PB16MTJ

No detailed pinout data available for MC9S08PB16MTJ.

Refer to the datasheet for full pin configuration.

Typical Applications

MC9S08PB16MTJ is suitable for 6 applications: Industrial Sensor Controller, Motor and Valve Control, Appliance Control Module, Building and HVAC Equipment, Low-Cost Analog Instrumentation, Battery-Powered Embedded Control.

🏭

Industrial Sensor Controller

The MC9S08PB16MTJ fits compact industrial sensor nodes because its 12-bit ADC can acquire analog measurements while the 8-bit S08 CPU performs local filtering, threshold decisions, and state-machine control. Operation from 2.7 V to 5.5 V supports both 3.3 V and 5 V industrial sensor architectures. The -40°C to +125°C temperature range covers demanding ambient conditions. Designers can use I2C to connect compatible sensors and flexible timers for periodic sampling. The main engineering trade-off is limited RAM at 1 KB, so buffering and communication code should remain compact.

🔧

Motor and Valve Control

The MC9S08PB16MTJ is appropriate for small motor, valve, and actuator controllers where deterministic timing and compact analog monitoring matter. Its flexible timers support periodic timing functions, while the 20 MHz S08 core can manage state machines and supervisory logic. The integrated comparator and amplifier can assist with current sensing or threshold detection around a power stage. The 16 KB Flash provides more code headroom than the 8 KB PB-family alternative, while 1 KB of RAM remains the main constraint for complex motion algorithms.

🏠

Appliance Control Module

In appliances and household equipment, the MC9S08PB16MTJ can manage user inputs, sensors, relays, indicators, and communication from one 20-pin TSSOP device. Its 5 V capability fits traditional appliance control environments, while the 2.7 V minimum supports lower-energy rails. The 12-bit ADC improves the available resolution for temperature, level, or position sensing, and I2C can connect display and sensor peripherals. Designers should reserve pins for programming, use the datasheet-defined decoupling arrangement, and validate reset behavior across the full 2.7 V to 5.5 V supply range.

🌐

Building and HVAC Equipment

The MC9S08PB16MTJ supports compact building-equipment controllers that monitor analog inputs, operate actuators, and coordinate local sensors. Its -40°C to +125°C operating range is valuable in environments that may experience wide temperature variation, and the flexible timers can organize periodic control tasks. The 12-bit ADC and analog comparator can serve pressure, temperature, or level conditioning functions. With 1 KB of RAM and a 20 MHz bus, the MCU is best suited to distributed control rather than resource-intensive central processing.

📟

Low-Cost Analog Instrumentation

The MC9S08PB16MTJ is well suited to compact instrumentation that converts a small analog signal into a readable or communicated measurement. The 12-bit ADC supplies the primary conversion function, while the integrated amplifier and comparator support conditioning and thresholding around the measurement chain. I2C can connect a display or digital sensor, and the 16 KB Flash can hold calibration and interface firmware. Designers should treat the analog pins as sensitive signal-routing points and follow the NXP layout guidance for grounding, decoupling, and input filtering.

🔋

Battery-Powered Embedded Control

The MC9S08PB16MTJ can serve as the control hub in a battery-powered embedded product because it operates from 2.7 V to 5.5 V and includes low-power-oriented embedded resources for sensor and actuator management. The 12-bit ADC reduces the need for a separate measurement converter, while I2C permits short, low-pin-count sensor connections. Firmware can use timers for periodic wake-up and measurement tasks. The device does not provide a dedicated low-power specification in the available product summary, so battery-life calculations should use measured current from the operating mode and confirm the selected regulator and sensor quiescent currents.

What is the operating voltage of the MC9S08PB16MTJ?
The MC9S08PB16MTJ operates from 2.7 V to 5.5 V. According to the NXP MC9S08PB16 datasheet, the 20 MHz bus is supported across this voltage range, allowing the same controller to serve 3.3 V and 5 V designs. The associated I/O and internal-circuit operating limits must also be observed when the supply is near either range boundary.
What are the key specifications of MC9S08PB16MTJ that engineers should know?
The MC9S08PB16MTJ is an 8-bit S08P MCU with a 20 MHz bus, 16 KB Flash, 1 KB RAM, 12-bit ADC, I2C, analog comparator, amplifier, and flexible timers in a 20-pin TSSOP. According to the NXP MC9S08PB16 datasheet, it supports up to 30 interrupt or reset sources and four nested interrupt levels, with an operating range of 2.7 V to 5.5 V.
How much Flash and RAM does the MC9S08PB16MTJ have?
The MC9S08PB16MTJ contains 16 KB of Flash program memory and 1 KB of RAM. The NXP MC9S08PB16 datasheet identifies the Flash organization as 16K x 8 bits. This memory balance is appropriate for compact embedded control firmware, while the MCU family reuses the S08 core, IP, and tools to simplify migration between compatible S08P devices.
What analog peripherals are built into the MC9S08PB16MTJ?
The MC9S08PB16MTJ integrates a 12-bit ADC, an analog comparator, and an amplifier. According to the NXP MC9S08PB16 datasheet, these functions simplify mixed-signal designs and can reduce the need for external analog components. The ADC supports analog measurement, while the comparator and amplifier support thresholding, signal conditioning, and other low-level analog tasks.
Where can I download the MC9S08PB16MTJ datasheet PDF?
The official MC9S08PB16MTJ datasheet PDF is available from NXP at https://www.nxp.com/docs/en/data-sheet/MC9S08PB16.pdf. The document covers MC9S08PB16 and MC9S08PB8 devices and is the primary reference for pin descriptions, electrical characteristics, memory organization, interrupt behavior, and application-circuit requirements.
Where can I find the MC9S08PB16MTJ pinout?
The MC9S08PB16MTJ pinout is shown in the pin-description table of the official NXP MC9S08PB16 datasheet. The device uses a 20-pin TSSOP package, and PCB signal assignments must be checked against the package drawing before layout release. Use the datasheet assignments for power, ground, reset, analog inputs, I2C, timers, and programming or debug functions.
Is MC9S08PB16MTJ suitable for industrial temperature environments?
Yes, the MC9S08PB16MTJ is specified for -40°C to +125°C operation. The NXP product information identifies the device as active, while the MC9S08PB16 datasheet defines the supported operating range. This temperature coverage is useful for industrial monitoring, appliance control, and equipment exposed to significant ambient-temperature variation.
What is the best drop-in replacement for MC9S08PB16MTJ?
The best drop-in replacement is the compatible S08P variant that retains the 20-pin TSSOP footprint, 2.7 V to 5.5 V supply range, 20 MHz bus, and required peripheral assignments. Candidates such as MC9S08PB8MTJ reduce Flash from 16 KB to 8 KB, while temperature-code variants retain memory size but change the qualification range. Verify pin functions and firmware behavior before replacement.
Can MC9S08PB8MTJ replace MC9S08PB16MTJ?
The MC9S08PB8MTJ can serve as a hardware candidate when its 20-pin TSSOP layout and required peripheral functions match, but its Flash capacity is 8 KB versus 16 KB for the MC9S08PB16MTJ. The NXP family documentation identifies both devices as supported members of the PB family. Confirm that the existing firmware fits within 8 KB and that no board-level function depends on the removed Flash capacity.
MC9S08PB16MTJ vs MC9S08PB8MTJ - which is better for new designs?
Choose the MC9S08PB16MTJ for firmware growth, code density, or future feature expansion because it provides 16 KB of Flash rather than 8 KB. The MC9S08PB8MTJ may be preferable for a small, fixed-control program that comfortably fits its memory. Both use the S08P architecture and 20-pin TSSOP package, so memory capacity and required peripherals should drive the decision.
When should I choose MC9S08PB16MTJ over a smaller-memory S08P MCU?
Choose the MC9S08PB16MTJ when code size, future updates, or application complexity could exceed an 8 KB Flash budget. Its 16 KB program memory provides twice the capacity of the MC9S08PB8MTJ while retaining the same S08P core and 20-pin TSSOP format. For very small programs, a smaller-memory variant is reasonable only after confirming code size and update requirements.
Is MC9S08PB16MTJ suitable for analog monitoring and sensor control?
Yes, the MC9S08PB16MTJ is suitable for compact sensor-control systems because it combines a 12-bit ADC, analog comparator, amplifier, I2C, and flexible timers. The NXP datasheet identifies these resources as core S08PB features. Use the ADC for measurement, the comparator for threshold decisions, and I2C for compatible sensors or interface devices while budgeting board area for filtering and pull-up components.
Where can I buy MC9S08PB16MTJ online?
Use the Request a Quote form on this page to request MC9S08PB16MTJ availability, lead time, and a current quotation. The form is the appropriate route for checking the exact 20-pin TSSOP MPN and confirming order quantities. The official NXP product page also links purchase options and current product-change information for the active device.
What is the price of MC9S08PB16MTJ?
Use the Request a Quote form on this page for the current MC9S08PB16MTJ price and quantity schedule. Quote requests avoid presenting a stale fixed price for this active MCU. Include the required quantity, target package, and delivery location so procurement can confirm the exact MC9S08PB16MTJ ordering configuration.
What is the lead time and stock status for MC9S08PB16MTJ?
Current MC9S08PB16MTJ stock, minimum order quantity, and lead time should be confirmed through the Request a Quote form on this page. The NXP product page identifies the device as active and provides buy options, while distributor availability can change by region and order quantity. Submit the exact MPN and required quantity to obtain a current commitment.

Engineering reference data for MC9S08PB16MTJ — comparison, design guidance, and compliance information.

Selection Guide

Choose the MC9S08PB16MTJ when a compact 8-bit control system needs 16 KB of Flash, 12-bit analog conversion, comparator and amplifier functions, I2C, and operation across 2.7 V to 5.5 V. Its -40°C to +125°C rating is appropriate for demanding ambient environments. Select MC9S08PB8MTJ or MC9S08PB8MTL only when the application, including future updates, safely fits 8 KB of Flash and the exact temperature qualification is acceptable. MC9S08PB16MTL is reasonable when its temperature range satisfies the product requirements. MC9S08PB8MJB and MC9S08PB16MJB can be evaluated as same-family alternatives, but their suffix-specific qualification and ordering configuration must be confirmed. In every case, verify the exact 20-pin TSSOP pin map, power requirements, programming method, and peripheral assignments before production release.

Comparison with Alternatives

Parameter This Product MC9S08PB8MTJ MC9S08PB8MTL MC9S08PB16MTL MC9S08PB8MJB MC9S08PB16MJB
Package 20-TSSOP 20-TSSOP 20-TSSOP 20-TSSOP 20-TSSOP 20-TSSOP
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors
CPU Architecture 8-bit S08 8-bit S08 8-bit S08 8-bit S08 8-bit S08 8-bit S08
Maximum CPU Frequency 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz
Operating Voltage Range 2.7 V to 5.5 V 2.7 V to 5.5 V 2.7 V to 5.5 V 2.7 V to 5.5 V 2.7 V to 5.5 V 2.7 V to 5.5 V
Flash Memory 16 KB 8 KB 8 KB 16 KB 8 KB 16 KB
RAM 1 KB 1 KB 1 KB 1 KB 1 KB 1 KB
ADC Resolution 12 bits 12 bits 12 bits 12 bits 12 bits 12 bits
Serial Interface I2C I2C I2C I2C I2C I2C

Key Differentiators

  • Twice the Flash memory of the PB8 alternatives (vs MC9S08PB8MTJ)
  • Extended 125°C upper temperature rating (vs MC9S08PB16MTL)
  • Full set of integrated analog resources (vs MC9S08PB8MTJ)

Design Notes

Route analog inputs away from switching nodes, high-current return paths, and digital clock signals. Use a continuous ground reference beneath the analog circuitry and follow the datasheet's recommended power-decoupling arrangement. Because the package uses a 20-pin TSSOP with closely spaced leads, verify pad dimensions, paste stencil, solderability, and assembly clearances against the latest NXP package drawing before releasing PCB artwork.

Decouple each supply connection with the capacitance specified by the NXP datasheet and place the components close to their package pins. The device supports 2.7 V to 5.5 V, but the selected regulator must remain within that interval under transient and temperature conditions. Check the I/O pin limits rather than assuming every signal can tolerate the maximum 5.5 V rail when the MCU operates from a 3.3 V supply.

Confirm the reset, programming, and debug signals against the exact package suffix before finalizing the schematic and PCB. The S08P family supports migration across pin-compatible devices, but firmware configuration, peripheral assignments, and programming access still need verification. Preserve access to these signals when replacing the MCU and include the recommended clock and decoupling layout around the 20-TSSOP footprint.

Do not select an 8 KB Flash replacement unless the compiled image and planned updates fit within that capacity. Also confirm the temperature qualification of any suffix change, since package compatibility alone does not establish environmental equivalence. For I2C designs, calculate pull-up values from the actual bus voltage, capacitance, and sink-current limit, and keep pull-up placement consistent with the intended bus topology.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The product summary identifies enhanced EFT/ESD performance but does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Confirm these attributes with NXP and the authorized supply chain before making a compliance declaration.

Related Searches

MC9S08PB16MTJ datasheet MC9S08PB16MTJ pinout MC9S08PB16MTJ datasheet pdf MC9S08PB16MTJ specifications MC9S08PB16MTJ equivalent MC9S08PB16MTJ replacement MC9S08PB16MTJ vs MC9S08PB8MTJ MC9S08PB16MTJ price MC9S08PB16MTJ stock NXP MC9S08PB16MTJ MC9S08PB16 20 TSSOP pinout MC9S08PB16MTJ application circuit

Related Components & Terms

NXP Semiconductors MC9S08PB16MTJ MC9S08PB16 MC9S08PB8MTJ MC9S08PB8MTL MC9S08PB16MTL MC9S08PB8MJB MC9S08PB16MJB S08P S08 8-bit CPU microcontroller MCU embedded microcontroller semiconductor 20-pin TSSOP TSSOP package family surface-mount package 12-bit ADC analog comparator operational amplifier I2C flexible timers Flash memory RAM EFT/ESD performance
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details