MC9S08PB16MTJ - 8-Bit 20MHz 16KB Flash MCU | NXP
부품 번호: MC9S08PB16MTJ ✓ 활성MC9S08PB16MTJ 개요
An 8-bit microcontroller is a semiconductor that executes firmware from embedded program memory while reading inputs and controlling outputs in a dedicated control system. The S08P belongs to the MCU hierarchy, where microcontrollers integrate a CPU, memory, peripherals, and communication interfaces into one device. The MC9S08PB16MTJ is suited to applications that require deterministic low-cost control without the memory or processing demands of a 32-bit MCU.
Key features include a maximum 20 MHz bus, 16 KB Flash for program storage, and 1 KB of RAM. The analog subsystem provides a 12-bit ADC plus comparator and amplifier functions, reducing the need for separate analog components. Up to 30 interrupt and reset sources, four levels of nested interrupts, an I2C interface, and flexible timers support responsive control and connected peripherals while preserving board space.
The S08 architecture reuses the established S08 core, intellectual property, and development tools, easing migration within the S08P family. Its 2.7 V to 5.5 V operating range supports both 3.3 V and 5 V system rails. The extended -40°C to +125°C temperature qualification makes it suitable for industrial environments where temperature variation and long service intervals must be considered.
Typical uses include industrial sensor controllers, motor and valve control, appliance interfaces, building equipment, low-cost instrumentation, and compact analog-monitoring products. The MCU can sample an analog input through its ADC, coordinate peripherals over I2C, and manage timing or actuator functions through its timer blocks without requiring a separate analog controller.
Designers should use the NXP datasheet pin-description table when assigning PCB signals and should preserve the package power and decoupling requirements. Pay particular attention to analog-input routing, I2C pull-up placement, and programming or debugging access. A common migration rule is to confirm that the alternative MCU has the same 20-pin TSSOP footprint and matching peripheral assignments before replacing this device.
This product page consolidates the key electrical, memory, analog, packaging, and environmental characteristics of the MC9S08PB16MTJ with pin-compatible S08P migration options, practical PCB guidance, and a parameter-by-parameter replacement table.
드롭인 대체품: MC9S08PB16MTJ — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MC9S08PB16MTJ (동일 폼 팩터 및 풋프린트) — 차이점: ADC Resolution, CPU Architecture, Operating Temperature Range, Program Memory Organization.
MC9S08PB8MTJ
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →MC9S08PB8MTL
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MC9S08PB16MTL
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MC9S08PB8MJB
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MC9S08PB16MJB
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
MC9S08PB16MTJ 최대 정격 & 전기적 특성
| CPU Architecture | 8-bit S08 central processor unit |
| Maximum CPU Frequency | 20 MHz |
| Operating Voltage Range | 2.7 V to 5.5 V |
| Flash Memory | 16 KB |
| Program Memory Organization | 16K x 8 bits |
| RAM | 1 KB |
| ADC Resolution | 12 bits |
| Analog Functions | ADC, analog comparator, and amplifier |
| Serial Interface | I2C |
| Timer Resources | Flexible timers |
| Interrupt and Reset Sources | Up to 30 sources |
| Nested Interrupt Levels | Up to 4 levels |
| 동작 온도 범위 | -40°C to +125°C |
| 패키지 | 20-pin TSSOP |
| 실장 유형 | Surface mount |
| Shipping Package | Tube |
| Nominal Supply Voltage | 5 V |
| ESD and EFT Performance | Enhanced EFT/ESD performance |
MC9S08PB16MTJ tube 핀 구성 가이드
MC9S08PB16MTJ(tube 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: MC9S08PB16MTJ.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
MC9S08PB16MTJ 적합 용도: 6 애플리케이션s: Industrial Sensor Controller, Motor and Valve Control, Appliance Control Module, Building and HVAC Equipment, Low-Cost Analog Instrumentation, Battery-Powered Embedded Control.
Industrial Sensor Controller
The MC9S08PB16MTJ fits compact industrial sensor nodes because its 12-bit ADC can acquire analog measurements while the 8-bit S08 CPU performs local filtering, threshold decisions, and state-machine control. Operation from 2.7 V to 5.5 V supports both 3.3 V and 5 V industrial sensor architectures. The -40°C to +125°C temperature range covers demanding ambient conditions. Designers can use I2C to connect compatible sensors and flexible timers for periodic sampling. The main engineering trade-off is limited RAM at 1 KB, so buffering and communication code should remain compact.
추천
Motor and Valve Control
The MC9S08PB16MTJ is appropriate for small motor, valve, and actuator controllers where deterministic timing and compact analog monitoring matter. Its flexible timers support periodic timing functions, while the 20 MHz S08 core can manage state machines and supervisory logic. The integrated comparator and amplifier can assist with current sensing or threshold detection around a power stage. The 16 KB Flash provides more code headroom than the 8 KB PB-family alternative, while 1 KB of RAM remains the main constraint for complex motion algorithms.
추천
Appliance Control Module
In appliances and household equipment, the MC9S08PB16MTJ can manage user inputs, sensors, relays, indicators, and communication from one 20-pin TSSOP device. Its 5 V capability fits traditional appliance control environments, while the 2.7 V minimum supports lower-energy rails. The 12-bit ADC improves the available resolution for temperature, level, or position sensing, and I2C can connect display and sensor peripherals. Designers should reserve pins for programming, use the datasheet-defined decoupling arrangement, and validate reset behavior across the full 2.7 V to 5.5 V supply range.
추천
Building and HVAC Equipment
The MC9S08PB16MTJ supports compact building-equipment controllers that monitor analog inputs, operate actuators, and coordinate local sensors. Its -40°C to +125°C operating range is valuable in environments that may experience wide temperature variation, and the flexible timers can organize periodic control tasks. The 12-bit ADC and analog comparator can serve pressure, temperature, or level conditioning functions. With 1 KB of RAM and a 20 MHz bus, the MCU is best suited to distributed control rather than resource-intensive central processing.
추천
Low-Cost Analog Instrumentation
The MC9S08PB16MTJ is well suited to compact instrumentation that converts a small analog signal into a readable or communicated measurement. The 12-bit ADC supplies the primary conversion function, while the integrated amplifier and comparator support conditioning and thresholding around the measurement chain. I2C can connect a display or digital sensor, and the 16 KB Flash can hold calibration and interface firmware. Designers should treat the analog pins as sensitive signal-routing points and follow the NXP layout guidance for grounding, decoupling, and input filtering.
추천
Battery-Powered Embedded Control
The MC9S08PB16MTJ can serve as the control hub in a battery-powered embedded product because it operates from 2.7 V to 5.5 V and includes low-power-oriented embedded resources for sensor and actuator management. The 12-bit ADC reduces the need for a separate measurement converter, while I2C permits short, low-pin-count sensor connections. Firmware can use timers for periodic wake-up and measurement tasks. The device does not provide a dedicated low-power specification in the available product summary, so battery-life calculations should use measured current from the operating mode and confirm the selected regulator and sensor quiescent currents.
추천
추천 제품 요약
엔지니어링 참조 데이터: MC9S08PB16MTJ — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MC9S08PB8MTJ | MC9S08PB8MTL | MC9S08PB16MTL | MC9S08PB8MJB | MC9S08PB16MJB |
|---|---|---|---|---|---|---|
| Package | 20-TSSOP | 20-TSSOP | 20-TSSOP | 20-TSSOP | 20-TSSOP | 20-TSSOP |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| CPU Architecture | 8-bit S08 | 8-bit S08 | 8-bit S08 | 8-bit S08 | 8-bit S08 | 8-bit S08 |
| Maximum CPU Frequency | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| Operating Voltage Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Flash Memory | 16 KB | 8 KB | 8 KB | 16 KB | 8 KB | 16 KB |
| RAM | 1 KB | 1 KB | 1 KB | 1 KB | 1 KB | 1 KB |
| ADC Resolution | 12 bits | 12 bits | 12 bits | 12 bits | 12 bits | 12 bits |
| Serial Interface | I2C | I2C | I2C | I2C | I2C | I2C |
주요 차별점
- Twice the Flash memory of the PB8 alternatives (vs MC9S08PB8MTJ)
- Extended 125°C upper temperature rating (vs MC9S08PB16MTL)
- Full set of integrated analog resources (vs MC9S08PB8MTJ)
설계 노트
Route analog inputs away from switching nodes, high-current return paths, and digital clock signals. Use a continuous ground reference beneath the analog circuitry and follow the datasheet's recommended power-decoupling arrangement. Because the package uses a 20-pin TSSOP with closely spaced leads, verify pad dimensions, paste stencil, solderability, and assembly clearances against the latest NXP package drawing before releasing PCB artwork.
Decouple each supply connection with the capacitance specified by the NXP datasheet and place the components close to their package pins. The device supports 2.7 V to 5.5 V, but the selected regulator must remain within that interval under transient and temperature conditions. Check the I/O pin limits rather than assuming every signal can tolerate the maximum 5.5 V rail when the MCU operates from a 3.3 V supply.
Confirm the reset, programming, and debug signals against the exact package suffix before finalizing the schematic and PCB. The S08P family supports migration across pin-compatible devices, but firmware configuration, peripheral assignments, and programming access still need verification. Preserve access to these signals when replacing the MCU and include the recommended clock and decoupling layout around the 20-TSSOP footprint.
Do not select an 8 KB Flash replacement unless the compiled image and planned updates fit within that capacity. Also confirm the temperature qualification of any suffix change, since package compatibility alone does not establish environmental equivalence. For I2C designs, calculate pull-up values from the actual bus voltage, capacitance, and sink-current limit, and keep pull-up placement consistent with the intended bus topology.
규정 준수 정보
The product summary identifies enhanced EFT/ESD performance but does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Confirm these attributes with NXP and the authorized supply chain before making a compliance declaration.