MCP3426A7-E/SN - 16-Bit Dual-Channel ADC | Microchip
MPN: MCP3426A7-E/SN ✓ ActiveMCP3426A7-E/SN Overview
A delta-sigma analog-to-digital converter is an ADC architecture that uses continuous-time oversampling and digital filtering to convert analog voltages into high-resolution digital codes. In the broader semiconductor hierarchy, the MCP3426 belongs to the ADC/DAC class, then to data converters, and finally to analog and mixed-signal integrated circuits. Its differential input architecture helps reject common-mode noise when measuring low-level sensor signals.
Key features include up to 16-bit resolution, two analog input channels, one sigma-delta conversion channel, and a 2.048 V onboard reference supporting a differential input range of ±2.048 V. The I2C interface supports digital communication with a host processor, while the low-noise architecture is intended for precision measurements where slow-changing signals provide high conversion effectiveness.
The MCP3426 family is designed for low-bandwidth instrumentation rather than high-speed waveform capture. The A7 speed grade performs 15 conversions per second, making it appropriate for temperature, pressure, chemical, load-cell, and industrial process measurements. The 2.7 V to 5.5 V supply range permits operation from common 3.3 V and 5 V systems, and the wide temperature range supports industrial and automotive environments.
Typical uses include bridge-sensor excitation and readout, battery monitoring, current sensing, potentiometer measurement, and environmental sensor interfaces. Differential signal measurement is particularly useful when a sensor output is referenced to a nearby analog ground or when the measured signal contains significant common-mode voltage.
PCB implementation should prioritize a quiet analog ground, short input traces, and separation from switching converters and high-current digital paths. Place the input bypass capacitor close to VDD and use the pin-description table in the manufacturer datasheet when assigning tracks. The effective input bandwidth must remain consistent with the selected conversion mode and digital filter.
This page combines manufacturer specifications, application guidance, parameter comparisons, and drop-in guidance to support component selection, PCB implementation, and sourcing for the MCP3426A7-E/SN.
Drop-in alternatives for MCP3426A7-E/SN — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with MCP3426A7-E/SN (same form factor and footprint) — differing in ADC Type, Differential Input Range, Number of Input Channels, Package.
MCP3426A6-E/SN
✅ Drop-In ⚠️ Specs Unverified📋 Reference alternative (not in catalog)
MCP3426A5-E/SN
✅ Drop-In ⚠️ Specs UnverifiedContact for price
View Datasheet →MCP3426A3-E/SN
✅ Drop-In ⚠️ Specs Unverified📋 Reference alternative (not in catalog)
MCP3426A2-E/SN
✅ Drop-In ⚠️ Specs UnverifiedContact for price
View Datasheet →MCP3426A1-E/SN
✅ Drop-In ⚠️ Specs UnverifiedContact for price
View Datasheet →MCP3426A7-E/SN Maximum Ratings & Electrical Characteristics
| ADC Type | 16-bit delta-sigma ADC |
| Number of Input Channels | 2 analog input channels |
| Conversion Architecture | 1 sigma-delta conversion channel |
| Conversion Rate | 15 samples/s |
| Resolution | Up to 16 bits |
| Input Type | Differential |
| Internal Reference Voltage | 2.048 V |
| Differential Input Range | ±2.048 V |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Operating Temperature Range | -55 °C to +125 °C |
| Package | 8-pin SOIC, 3.90 mm width |
| Terminal Count | 8 terminals |
| Mounting Type | Surface mount |
| Package Code | SOIC |
| Package Shape | Rectangular |
| Interface | I2C |
MCP3426A7-E/SN Pin Configuration
| Pin 1 | VIN+ — Positive differential analog input |
| Pin 2 | VIN- — Negative differential analog input |
| Pin 3 | VREF — External or internal reference node |
| Pin 4 | VSS — Analog ground |
| Pin 5 | SCL — I2C clock input |
| Pin 6 | SDA — I2C bidirectional data line |
| Pin 7 | CS — Chip-select input |
| Pin 8 | VDD — Positive supply voltage |
Typical Applications
MCP3426A7-E/SN is suitable for 6 applications: Precision Temperature Measurement, Pressure and Load-Cell Instrumentation, Battery and Power Rail Monitoring, Current Sensing with Shunt Amplifier, Chemical and Environmental Sensor Interface, Industrial Process and Potentiometer Readout.
Precision Temperature Measurement
The MCP3426A7-E/SN is well suited to slow-changing temperature signals because its 15 samples/s conversion rate provides substantially more updates than the A1 and A2 speed grades. A 16-bit conversion path can preserve small changes from RTDs, thermistors, and digital temperature sensors after suitable excitation or conditioning. The two differential inputs allow one channel to monitor a temperature sensor while the second supports a reference, offset, or another sensor. Use the integrated 2.048 V reference when the sensor chain is ratiometric, and keep analog traces away from switching supplies. The main design trade-off is that a delta-sigma converter cannot capture fast transients; select a different ADC architecture if the temperature signal contains high-frequency components.
Recommended
Pressure and Load-Cell Instrumentation
Bridge-based pressure and load-cell systems benefit from the MCP3426A7-E/SN's differential inputs, up to 16-bit resolution, and 15 samples/s throughput. Two differential channels can support a full bridge and a reference or temperature-compensation input. Because the output codes remain useful for mechanically slow signals, the converter provides stable measurements without the power and complexity of a high-speed SAR ADC. Place the bridge excitation and input-return paths away from motor and relay currents, and use a quiet analog-ground region around the converter. Verify input settling and acquisition timing against the selected conversion mode, as these can determine whether the A7 speed grade is necessary.
Recommended
Battery and Power Rail Monitoring
The MCP3426A7-E/SN can monitor slowly varying supply or battery voltages using its differential inputs and integrated 2.048 V reference. The 2.7 V to 5.5 V operating range permits deployment in 3.3 V and 5 V systems, while 15 samples/s is sufficient for supervisory trends, energy accounting, and fault logging. A scaled voltage divider can feed one input and a known reference can feed the other when differential ratiometric compensation is useful. Protect the input network from transients and ensure divider resistance keeps measurement leakage within the device's input-current expectations. Because this is a low-speed converter, a sampled monitoring application is preferable to one requiring instantaneous detection of a fast transient.
Recommended
Current Sensing with Shunt Amplifier
The MCP3426A7-E/SN can digitize the differential voltage generated by a low-ohm shunt and current-sense amplifier. Its two differential channels allow simultaneous measurement of the load current and a voltage, temperature, or reference signal. At 15 samples/s, the converter suits motor current, battery current, and power-system monitoring where the measured current changes more slowly than the device's minimum acquisition interval. The differential input arrangement helps reject supply and ground noise common to both inputs. Choose a shunt and amplifier with suitable offset, gain, bandwidth, and common-mode ratings, then verify that the converter's input range is not exceeded during overload or startup conditions.
Recommended
Chemical and Environmental Sensor Interface
The MCP3426A7-E/SN is appropriate for electrochemical, gas, humidity, and conductivity sensors whose outputs vary slowly enough for delta-sigma conversion. Its two differential channels can read a sensor output and a compensation or reference signal, while the internal 2.048 V reference supports ratiometric measurement of potentiometric sensors. The 16-bit resolution can resolve small changes from high-impedance sensing elements when the complete analog front end is designed for low leakage and noise. Use guarding and short analog traces to reduce leakage, keep contaminants away from sensitive nodes, and follow the sensor manufacturer's grounding recommendations. Verify the conversion rate against the application's required reaction time.
Recommended
Industrial Process and Potentiometer Readout
The MCP3426A7-E/SN can read potentiometers, resistive dividers, and slow process-control sensors through an I2C-connected analog front end. Its 15 samples/s conversion rate is more than adequate for position feedback, setpoint monitoring, and panel controls that do not require rapid updates. Two analog channels allow multiplexing through suitable front-end circuitry or simultaneous monitoring of a control and feedback element. The onboard 2.048 V reference simplifies ratiometric excitation of resistive sensors, while the differential inputs offer flexibility when the measured node is offset. Keep the sensor return path close to the converter ground and avoid routing input nets beneath switching-regulator areas. Confirm the input settling requirements for the selected conversion mode.
Recommended
Recommended Products Summary
Engineering reference data for MCP3426A7-E/SN — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | MCP3426A6-E/SN | MCP3426A5-E/SN | MCP3426A3-E/SN | MCP3426A2-E/SN | MCP3426A1-E/SN |
|---|---|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| ADC Resolution | Up to 16 bits | Up to 16 bits | Up to 16 bits | Up to 16 bits | Up to 16 bits | Up to 16 bits |
| Conversion Rate | 15 samples/s | Approximately 13.75 samples/s | Approximately 12.5 samples/s | Approximately 5 samples/s | Approximately 3.75 samples/s | Approximately 1.25 samples/s |
| Input Channels | 2 differential inputs | 2 differential inputs | 2 differential inputs | 2 differential inputs | 2 differential inputs | 2 differential inputs |
| Internal Reference | 2.048 V | 2.048 V | 2.048 V | 2.048 V | 2.048 V | 2.048 V |
| Supply Voltage Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Operating Temperature Range | -55 °C to +125 °C | -55 °C to +125 °C | -55 °C to +125 °C | -55 °C to +125 °C | -55 °C to +125 °C | -55 °C to +125 °C |
| Digital Interface | I2C | I2C | I2C | I2C | I2C | I2C |
Key Differentiators
- Higher conversion throughput within the same MCP3426 family (vs MCP3426A6-E/SN)
- Balance of throughput and sensitivity for slowly varying measurements (vs MCP3426A1-E/SN)
- Differential precision measurement with integrated reference (vs MCP3426A3-E/SN)
Design Notes
Route VIN+ and VIN- as a compact, closely coupled differential pair to minimize susceptibility to electromagnetic interference and ground-current coupling. Place input filtering components close to their associated pins, and keep the analog section physically separated from switching-regulator traces, relay outputs, and high-current return paths. Maintain a continuous analog ground reference beneath the converter and follow the manufacturer datasheet layout guidance.
Treat the two analog inputs as a precision measurement interface. Use a low-leakage protection network, avoid excessive resistance around sensitive sensor nodes, and confirm that the front-end output settles within the acquisition time of the selected conversion mode. The delta-sigma digital filter provides averaging for low-frequency signals but does not remove aliasing before conversion, so anti-alias filtering remains necessary when frequency content exceeds the usable measurement bandwidth.
Place the supply bypass capacitor immediately across VDD and VSS near the device, and provide a quiet analog supply path. The MCP3426A7-E/SN accepts a 2.7 V to 5.5 V operating range, but measured accuracy and noise can still be affected by supply ripple and shared return impedance. Do not route return current from the analog input shield or sensor excitation directly through the converter's sensitive ground node.
Do not treat the A7 speed grade as interchangeable with every MCP3426 ordering code without checking conversion timing and acquisition behavior. Likewise, do not substitute a 2x3 mm DFN variant on an 8-pin SOIC footprint. Confirm the complete suffix, package dimensions, pin functions, reference configuration, I2C address behavior, and required conversion mode before approving a replacement or second-source order.
Compliance Information
The -55 °C to +125 °C operating-temperature specification does not by itself establish AEC-Q100 qualification. Compliance declarations must be confirmed for the exact order code.