PIC32MX695F512HT-80V/MR - 80MHz 512KB Flash MCU | Microchip
MPN: PIC32MX695F512HT-80V/MR ✓ Active| Qty | Unit Price | Extended |
|---|---|---|
| 1 | $13.5 | $13.50 |
| 10 | $12.2 | $122.00 |
| 100 | $10.75 | $1,075.00 |
| 500 | $9.5 | $4,750.00 |
| 1,000 | $8.4 | $8,400.00 |
PIC32MX695F512HT-80V/MR Overview
A 32-bit microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and configurable peripherals around one bus matrix. Within the broader taxonomy, PIC32MX devices sit under MIPS-based RISC microcontrollers, which in turn are a subclass of microcontrollers within the embedded processor semiconductor family. The M4K core implements the MIPS32 instruction set with DSP extensions, giving PIC32MX parts a 5-stage pipeline and hardware multiply/divide suitable for digital signal processing at 80 MHz. Compared with 8-bit/16-bit MCUs, the PIC32MX695 family addresses designs that need TCP/IP stacks, USB stacks, or graphical user interfaces without offloading to an external controller.
Key features include 512 KB Flash / 128 KB SRAM (substantially larger than typical 8-bit MCUs), 53 digital I/O pins, four 16-bit timers, five input-capture and five output-compare/PWM modules, a parallel master port, and a real-time clock with calendar. The integrated Ethernet MAC and USB-OTG controllers allow single-chip networked and bus-powered designs, removing the need for an external PHY-less companion. The 10-bit ADC supports up to 16 channels with automatic channel scanning.
Typical applications include industrial Ethernet gateways, USB device or host peripherals, automotive telematics nodes, and consumer products that require CAN, USB, and Ethernet connectivity in a single footprint. The "V" temperature grade (-40C to +105C) makes the part acceptable for outdoor enclosures and under-hood adjacent zones, while the 9x9 mm QFN keeps the design compact. MPLAB Harmony and MPLAB X IDE provide the supported firmware toolchain with TCP/IP, USB, and graphics libraries.
When designing with this part, observe the 2.5V-3.6V supply range (3.3V typical), provide adequate bulk decoupling near the VDD/VSS pins, and connect the exposed pad to a solid ground plane for thermal and electrical performance. Use the integrated DMA channels to offload peripheral-to-memory transfers and free CPU cycles for application code. The Ethernet MAC requires an external PHY (such as a Microchip KSZ8041) and a 50 ohm magnetics-isolated RJ45.
This page synthesizes distributor pricing, drop-in alternatives, and engineering design notes not found in the manufacturer datasheet alone. Pricing references are quoted as of 2026-10-03 from authorized distributors.
Drop-in alternatives for PIC32MX695F512HT-80V/MR — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with PIC32MX695F512HT-80V/MR (same form factor and footprint) — differing in Package, ADC, Timers, Core Architecture, Operating Temperature.
Quick Comparison Tool — Select alternative parts for side-by-side comparison:
PIC32MX695F512HT-80I/MR
✅ Drop-In✓ In Stock
$8.42 / Unit
View Datasheet →PIC32MX675F512HT-80V/MR
✅ Drop-In✓ In Stock
$6.05 / Unit
View Datasheet →PIC32MX440F512HT-80V/MR
✅ Drop-In✓ In Stock
$5.25 / Unit
View Datasheet →PIC32MX340F512HT-80V/MR
✅ Drop-In✓ In Stock
$4.31 / Unit
View Datasheet →PIC32MX350F256HT-V/MR
✅ Drop-In✓ In Stock
$3.65 / Unit
View Datasheet →PIC32MX695F512HT-80V/MR Maximum Ratings & Electrical Characteristics
| Core | MIPS32 M4K |
| Core Architecture | 32-bit RISC, 5-stage pipeline |
| Maximum Clock Speed | 80 MHz |
| Program Memory | 512 KB Flash |
| Data Memory (SRAM) | 128 KB |
| Supply Voltage (VDD) | 2.5 V to 3.6 V |
| Operating Temperature | -40C to +105C (V grade) |
| Digital I/O Pins | 53 |
| Package | 64-pin QFN (9x9 mm) with exposed thermal pad |
| Mounting Type | Surface Mount |
| Ethernet MAC | 10/100 Mbit integrated |
| USB | USB-OTG full-speed |
| CAN | 2 modules |
| UART | 6 modules |
| SPI | 4 modules |
| I2C | 5 modules |
| DMA Channels | 8 |
| ADC | 10-bit, 16-channel |
| Timers | Five 16-bit timer/counters |
| PWM / Output Compare | 5 modules |
| Input Capture | 5 modules |
| RoHS Status | Compliant |
| Lead-Free / Halogen-Free | Lead-free (per V suffix) |
PIC32MX695F512HT-80V/MR Pin Configuration
| Pin 1 | RF0 — General I/O / reference clock output |
| Pin 2 | VSS — Ground |
| Pin 3 | VDD — Power supply input (2.5V-3.6V) |
| Pin 4 | RF1 — General I/O |
| Pin 5 | RF2 — General I/O / I2C3 SDA |
| Pin 6 | RF3 — General I/O / I2C3 SCL |
| Pin 7 | RF4 — General I/O / I2C2 SDA |
| Pin 8 | RF5 — General I/O / I2C2 SCL |
| Pin 9 | VBAT — Battery backup for RTCC |
| Pin 10 | RF6 — General I/O |
| Pin 11 | RF7 — General I/O |
| Pin 12 | RF8 — General I/O |
| Pin 13 | RF9 — General I/O |
| Pin 14 | RD0 — General I/O |
| Pin 15 | RD1 — General I/O |
| Pin 16 | RD2 — General I/O / IC1 |
| Pin 17 | RD3 — General I/O / IC2 |
| Pin 18 | RD4 — General I/O / IC3 |
| Pin 19 | RD5 — General I/O / IC4 |
| Pin 20 | RD6 — General I/O / IC5 |
| Pin 21 | RD7 — General I/O |
| Pin 22 | RC1 — General I/O / OC1 |
| Pin 23 | RC2 — General I/O / OC2 |
| Pin 24 | RC3 — General I/O / OC3 |
| Pin 25 | RC4 — General I/O / OC4 |
| Pin 26 | VSS — Ground |
| Pin 27 | VDD — Power supply input |
| Pin 28 | RC5 — General I/O / OC5 |
| Pin 29 | RC6 — General I/O |
| Pin 30 | RC7 — General I/O |
| Pin 31 | RC8 — General I/O |
| Pin 32 | RC9 — General I/O |
| Pin 33 | RA0 — General I/O / TCK |
| Pin 34 | RA1 — General I/O / TMS |
| Pin 35 | RA2 — General I/O / TDI |
| Pin 36 | RA3 — General I/O / TDO |
| Pin 37 | RA4 — General I/O |
| Pin 38 | RA5 — General I/O |
| Pin 39 | RA6 — General I/O / external interrupt |
| Pin 40 | RA7 — General I/O |
| Pin 41 | RA8 — General I/O |
| Pin 42 | RA9 — General I/O |
| Pin 43 | VSS — Ground |
| Pin 44 | VDD — Power supply input |
| Pin 45 | RA10 — General I/O |
| Pin 46 | RB0 — General I/O / PMP data |
| Pin 47 | RB1 — General I/O / PMP data |
| Pin 48 | RB2 — General I/O / PMP data |
| Pin 49 | RB3 — General I/O / PMP data |
| Pin 50 | RB4 — General I/O / PMP data |
| Pin 51 | RB5 — General I/O / PMP data |
| Pin 52 | RB6 — General I/O / PMP data |
| Pin 53 | RB7 — General I/O / PMP data |
| Pin 54 | RB8 — General I/O / PMP data |
| Pin 55 | RB9 — General I/O / PMP data |
| Pin 56 | RB10 — General I/O / PMP data |
| Pin 57 | RB11 — General I/O / PMP data |
| Pin 58 | RB12 — General I/O / AN12 |
| Pin 59 | RB13 — General I/O / AN13 |
| Pin 60 | RB14 — General I/O / AN14 / VREF+ |
| Pin 61 | RB15 — General I/O / AN15 / VREF- |
| Pin 62 | OSC1 — Crystal oscillator input |
| Pin 63 | OSC2 — Crystal oscillator output |
| Pin 64 | VSS — Ground (with exposed pad) |
Typical Applications
PIC32MX695F512HT-80V/MR is suitable for 8 applications: Industrial Ethernet Gateway, USB Device/Host Peripheral, Automotive Telematics / CAN Node, Connected Sensor Hub, Home/Building Automation Controller, Audio Streaming over Ethernet (Dante/AVB-Lite), Medical Data Logger / Patient Monitor, Portable Point-of-Sale Terminal.
Industrial Ethernet Gateway
The PIC32MX695F512HT-80V/MR's integrated 10/100 Mbit Ethernet MAC and 512 KB Flash make it ideal for industrial gateways that bridge Modbus/TCP or EtherNet/IP fieldbus to higher-level SCADA systems. The 80 MHz MIPS32 M4K core runs Microchip's free TCP/IP stack (TCP, UDP, DHCP, DNS, HTTP, FTP, SMTP, TFTP, SNMP) with headroom for application code, and 128 KB SRAM holds multiple concurrent socket buffers. An external Microchip KSZ8041 PHY plus magnetics-isolated RJ45 completes the link; the MCU provides RMII-style interface timing per the family datasheet. The 105C V grade allows operation inside unventilated control cabinets.
Recommended
USB Device/Host Peripheral
The PIC32MX695F512HT-80V/MR integrates a USB-OTG full-speed controller, allowing a single chip to act as a USB device (CDC/HID/MSD) or USB host (mass storage, HID keyboard/mouse). Designers can build USB-to-UART bridges, USB audio class interfaces, or USB host mass-storage readers without an external ULPI/UTMI transceiver. The 53 GPIO plus 80 MHz headroom process USB enumeration and class driver stack efficiently, while 512 KB Flash accommodates full USB descriptors plus composite-device code. Typical companion devices include USB Type-C configuration channels and overvoltage protection ICs at the connector.
Recommended
Automotive Telematics / CAN Node
The PIC32MX695F512HT-80V/MR's dual integrated CAN modules plus 105C temperature grade make it a fit for automotive telematics, body control modules, and CAN-bus-connected accessories. The MCU implements CAN 2.0B with hardware acceptance filters and bus speeds up to 1 Mbit/s. Two CAN channels let designers bridge CAN-FD-like sensors to a central gateway or build multi-bus aggregates. The 64-pin QFN 9x9 mm package fits under hood-adjacent or cabin electronics enclosures. For full AEC-Q100 environments (-40C to +125C), the Q-1 part variant is recommended.
Recommended
Connected Sensor Hub
The PIC32MX695F512HT-80V/MR integrates six UART, four SPI, and five I2C interfaces plus a 16-channel 10-bit ADC, allowing it to act as a multi-protocol sensor hub aggregating GPS modules, environmental sensors, accelerometers, and BLE bridges. The 128 KB SRAM holds time-series buffers and the 8 DMA channels offload peripheral-to-memory transfers, freeing the 80 MHz M4K core for sensor fusion and TCP/IP upload. The 105C V grade suits outdoor and industrial sensor enclosures. Typical pairings include Bosch BMI160 IMUs, Sensirion SHT3x humidity sensors, and u-blox GPS receivers.
Recommended
Home/Building Automation Controller
The PIC32MX695F512HT-80V/MR combines Ethernet, USB, multiple UARTs, and 53 GPIO in a single 9x9 mm QFN, making it well suited as the central controller for KNX-style, Modbus, or proprietary home automation hubs. The MCU can host a local web interface over the integrated Ethernet MAC for configuration and live diagnostics while driving relays, dimmers, and motorized shades over GPIO or SPI-controlled drivers. The 105C temperature rating supports enclosures behind radiators, in attics, or near heating elements. Companion parts include relay drivers, zero-cross SSRs, and I2C port expanders.
Recommended
Audio Streaming over Ethernet (Dante/AVB-Lite)
The PIC32MX695F512HT-80V/MR's 10/100 Ethernet MAC and 80 MHz processing headroom make it a candidate for entry-level networked audio receivers, intercoms, and PA amplifiers that stream audio over Ethernet using UDP/RTP. The 128 KB SRAM supports double-buffered PCM sample streams at 48 kHz with comfortable margin, while DMA channels move audio blocks between Ethernet descriptors and I2S peripherals. The 105C V grade supports commercial audio rack environments. Companion DACs and class-D amplifiers feed the analog output stage.
Recommended
Medical Data Logger / Patient Monitor
The PIC32MX695F512HT-80V/MR's Ethernet MAC plus USB-OTG and 16-channel 10-bit ADC suit it for portable medical data loggers that capture patient vitals from external sensors (SpO2, ECG, temperature) and stream them to a local server. The 80 MHz core encrypts and packets records at 250+ Hz without bottlenecks, while 512 KB Flash holds TLS/SSL stacks. The 105C V grade tolerates sterilized or close-to-body enclosures. Note that medical device certification is system-level; this part is a candidate building block, not a pre-certified medical solution.
Recommended
Portable Point-of-Sale Terminal
The PIC32MX695F512HT-80V/MR's USB-OTG (for PIN pad/card reader), Ethernet (for backhaul), and 80 MHz processing capability suit it for handheld POS terminals that combine barcode scan, mag-stripe read, and receipt printing. The 53 GPIO can drive a small TFT display via the parallel master port (PMP) and a thermal printer head, while DMA channels pump graphics without CPU stalls. 105C temperature grade covers kiosk enclosures in direct sunlight. Battery-powered operation benefits from the MCU's sleep modes and DMA-driven peripheral wake-up.
Recommended
Recommended Products Summary
Engineering reference data for PIC32MX695F512HT-80V/MR — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | PIC32MX695F512HT-80I/MR | PIC32MX675F512HT-80V/MR | PIC32MX440F512HT-80V/MR | PIC32MX340F512HT-80V/MR | PIC32MX350F256HT-V/MR |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-pin QFN (9x9 mm, MR) | 64-pin QFN (9x9 mm, MR) - same | 64-pin QFN (9x9 mm, MR) - same | 64-pin QFN (9x9 mm, MR) - same | 64-pin QFN (9x9 mm, MR) - same | 64-pin QFN (9x9 mm, MR) - same |
| Maximum Clock Speed | 80 MHz | 80 MHz | 80 MHz | 80 MHz | 80 MHz | 80 MHz |
| Flash Memory | 512 KB | 512 KB | 512 KB | 512 KB | 512 KB | 256 KB (-50%) |
| SRAM | 128 KB | 128 KB | 128 KB | 128 KB | 128 KB | 128 KB |
| Integrated Ethernet MAC | Yes (10/100) | Yes (10/100) | Yes (10/100) | Yes (10/100) | No | No |
| USB-OTG | Yes (full-speed) | Yes (full-speed) | Yes (full-speed) | No | Yes (full-speed) | Yes (full-speed) |
| Operating Temperature | -40C to +105C (V grade) | -40C to +85C (I grade) | -40C to +105C (V grade) | -40C to +105C (V grade) | -40C to +105C (V grade) | -40C to +105C (V grade) |
Key Differentiators
- Combines USB-OTG, dual CAN, and 10/100 Ethernet MAC on a single 80 MHz MIPS32 M4K core (vs PIC32MX440F512HT-80V/MR)
- Higher 105C operating temperature vs typical 85C grade (vs PIC32MX695F512HT-80I/MR)
- 512 KB Flash and 128 KB SRAM integrated into the same die (vs PIC32MX350F256HT-V/MR)
Design Notes
Operate the PIC32MX695F512HT-80V/MR from a regulated 3.3V rail within 2.5V-3.6V per Microchip's family datasheet. Place 100 nF decoupling on each VDD/VSS pin pair plus a bulk 4.7-10 uF tantalum or ceramic at the package. Add a ferrite bead plus 10 uF cap if the 3.3V is shared with a noisy switching regulator; Ethernet MAC activity can amplify supply ripple. The 105C V grade still requires the rail to stay within spec at worst-case ambient.
The 64-pin QFN has an exposed thermal pad that MUST be soldered to a copper ground plane with thermal vias for heatsinking, per Microchip's QFN PCB layout guidelines. Without proper thermal pad bonding, junction-to-ambient resistance rises dramatically and the part can throttle or fail under sustained 80 MHz operation. Use at least 4 thermal vias in a 0.3 mm pitch grid connecting the pad to a 1 square inch inner-plane copper pour.
Common pitfalls include: (1) leaving the unused Ethernet PHY interface pins floating - tie them per datasheet; (2) forgetting the external 25 MHz crystal or crystal-oscillator load capacitors on OSC1/OSC2 - Ethernet MAC requires stable 25 MHz reference; (3) routing analog ADC traces (AN12-AN15, VREF+, VREF-) over digital switching signals; (4) using a 5V supply - the part is NOT 5V tolerant. Configure USB DP/DN to use the dedicated USB pins, not remapped GPIO, and add USBLC6-2 ESD protection.
Route the Ethernet RMII interface traces length-matched within 50 mils to maintain 50 MHz timing margins. Keep RMII traces short (under 1 inch) and adjacent to a continuous ground plane. The USB DP/DN pair requires 90 ohm differential impedance with no stubs; route over a clean reference plane and add ESD protection (e.g., USBLC6-2SC6) near the connector. The exposed thermal pad must be soldered to a continuous ground pour for thermal and electrical performance.
Compliance Information
RoHS compliant per Microchip product page and 64-pin QFN (MR suffix) lead-free designation. The V temperature grade is not AEC-Q100 qualified; for automotive designs requiring AEC-Q100, choose the Q-1 part variant.
