PIC32MX775F512HT-80I/MR - 80MHz 512KB MCU USB/CAN/Ethernet | Microchip
MPN: PIC32MX775F512HT-80I/MR ✓ Active| Qty | Unit Price | Extended |
|---|---|---|
| 1 | $10.9956 | $11.00 |
| 10 | $10.45 | $104.50 |
| 100 | $9.42 | $942.00 |
| 500 | $8.65 | $4,325.00 |
| 1,000 | $7.88 | $7,880.00 |
PIC32MX775F512HT-80I/MR Overview
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and a rich set of peripherals into one package. Within the broader taxonomy, the PIC32MX775 sits under 32-bit MCU -> RISC MCU -> microcontroller -> integrated circuit -> semiconductor. Compared with 8-bit and 16-bit MCUs, a 32-bit MCU executes instructions on 32-bit data paths, allowing larger address spaces, higher throughput, and richer peripheral integration for connected embedded applications.
Key features of the PIC32MX775F512HT-80I/MR include 80 MHz core speed, 512 KB Flash, 64 KB SRAM, integrated USB 2.0 Full-Speed device/host/OTG, two CAN 2.0b controllers, a 10/100 Mbit Ethernet MAC, 8-channel DMA, and 5 timers / 5 IC/OC / 5 I2C / 4 UART / 2 SPI peripherals. The 64-VQFN (9x9 mm) package exposes 53 digital I/O pins and supports industrial operating temperatures from -40C to +85C.
The device uses the MIPS32 M4K core with 5-stage pipeline and prefetch cache, executing most instructions in a single clock cycle. The dual Flash panel and live update partition allow firmware field updates via bootloader, while 8 DMA channels offload data movement between peripherals and RAM. USB, CAN, and Ethernet MACs share DMA, reducing CPU interrupt load in connected designs.
Typical applications include industrial Ethernet nodes, CAN-connected motor and building automation controllers, USB peripherals and embedded hosts, factory automation gateways, and connected medical or instrumentation devices. The PIC32MX5/6/7 series is fully supported by MPLAB Harmony and MPLAB X IDE for firmware development.
When designing, ensure the USB D+/D- trace impedance is 90 ohms differential and add a 1 uF bulk capacitor near the VBUS pin. Use the internal pull-up on D+ only in bus-powered designs; for self-powered devices, drive D+ through an external switchable resistor to avoid back-powering the host port.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
Drop-in alternatives for PIC32MX775F512HT-80I/MR — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with PIC32MX775F512HT-80I/MR (same form factor and footprint) — differing in ADC, Package, Operating Temperature, Core Architecture, DMA Channels.
Quick Comparison Tool — Select alternative parts for side-by-side comparison:
PIC32MX775F512H-80I/MR
✅ Drop-In✓ In Stock
$5.41 / Unit
View Datasheet →PIC32MX695F512HT-80I/MR
✅ Drop-In✓ In Stock
$8.42 / Unit
View Datasheet →PIC32MX675F512HT-80I/MR
✅ Drop-In✓ In Stock
$6.45 / Unit
View Datasheet →PIC32MX764F128HT-I/MR
✅ Drop-In✓ In Stock
$6.04 / Unit
View Datasheet →PIC32MX570F512HT-50I/MR
✅ Drop-In📋 Reference alternative (not in catalog)
PIC32MX440F512HT-80I/MR
✅ Drop-In✓ In Stock
$6.2 / Unit
View Datasheet →PIC32MX775F512HT-80I/MR Maximum Ratings & Electrical Characteristics
| Core Architecture | MIPS32 M4K 32-bit RISC |
| Maximum CPU Speed | 80 MHz |
| Program Memory (Flash) | 512 KB (512K x 8) |
| Data Memory (SRAM) | 64 KB |
| Supply Voltage | 2.3 V to 3.6 V |
| Operating Temperature | -40 C to +85 C (Industrial) |
| Package | 64-VQFN (9x9 mm) |
| Mounting Type | Surface Mount |
| I/O Pins | 53 |
| USB Interface | USB 2.0 Full-Speed Device/Host/OTG |
| CAN | 2 x CAN 2.0b |
| Ethernet | 10/100 Mbit MAC (RMII/MII) |
| DMA Channels | 8 |
| Timers | 5 x 16-bit |
| UART / I2C / SPI | 4 UART / 5 I2C / 2 SPI |
| ADC | 16-channel 10-bit |
| MSL Level | 3 (168 hours) |
| RoHS Status | Compliant |
PIC32MX775F512HT-80I/MR 64-vqfn (9x9 mm) Pin Configuration Guide
Pin configuration for PIC32MX775F512HT-80I/MR (64-vqfn (9x9 mm) package). This digital IC includes GPIO, communication interfaces (UART, SPI, I2C), and power pins. Refer to the manufacturer datasheet for alternate pin functions and configuration options. Essential for embedded system design and PCB layout.
No detailed pinout data available for PIC32MX775F512HT-80I/MR.
Refer to the datasheet for full pin configuration.
Typical Applications
PIC32MX775F512HT-80I/MR is suitable for 6 applications: Industrial Ethernet Gateway, USB-Connected Embedded Peripherals, CAN Bus Industrial Nodes, Building Automation Controllers, Connected Medical Instrumentation, Multi-Protocol Sensor Hubs.
Industrial Ethernet Gateway
The PIC32MX775F512HT-80I/MR's integrated 10/100 Mbit Ethernet MAC and 80 MHz MIPS32 M4K core make it well suited for industrial Ethernet gateways that must run a lightweight TCP/IP stack (e.g., TCP/IP + MQTT or Modbus TCP) alongside application logic. Placed on the fieldbus side of a factory node, it bridges Ethernet to local CAN and UART sensors while the 8-channel DMA engine offloads packet movement from the CPU. The 64 KB SRAM comfortably holds a TCP/IP socket buffer plus application queues, and the 512 KB Flash is large enough for the Harmony 3 Net Preset plus user firmware without external program memory.
Recommended
USB-Connected Embedded Peripherals
The PIC32MX775F512HT-80I/MR's USB 2.0 Full-Speed device/host/OTG controller, combined with 53 digital I/O pins and 64 KB SRAM, supports USB HID/CDC/MSC peripherals such as data loggers, human-interface panels, and instrument front-ends. A typical design places the MCU between a host PC and downstream UART/I2C/SPI sensors, presenting as a composite USB device. The 80 MHz core provides enough headroom for USB stack plus real-time sampling, and the 512 KB Flash lets Harmony 3 USB stacks fit alongside application firmware without an external boot-loader partition.
Recommended
CAN Bus Industrial Nodes
With two independent CAN 2.0b controllers and a 80 MHz core, the PIC32MX775F512HT-80I/MR is well matched to industrial CAN nodes such as motor controllers, building-automation sensors, and automotive-bus gateways. Each CAN controller has its own DMA channel, so traffic on one bus does not block the other. The 53 I/O pins expose ample PWM/IC/OC channels for motor-drive interface, and the 64 KB SRAM holds CAN message queues without dropping frames under burst conditions.
Recommended
Building Automation Controllers
The PIC32MX775F512HT-80I/MR's mix of Ethernet, dual CAN, USB, and 53 I/O pins serves BACnet/Modbus building-automation controllers that bridge multiple field buses. The 80 MHz M4K core handles BACnet/IP plus local control loops, while 64 KB SRAM maintains HVAC schedule tables and trend logs. Operating temperature -40 C to +85 C and the 64-VQFN (9x9) exposed-pad package make it thermally robust inside equipment rooms without requiring a heatsink above 0.5 W dissipation.
Recommended
Connected Medical Instrumentation
The PIC32MX775F512HT-80I/MR provides 16-channel 10-bit ADC, USB, and ample I/O for connected medical instruments such as portable monitors and bench-top analyzers. The 80 MHz core runs USB CDC plus signal-processing loops, while 512 KB Flash holds firmware for waveform capture and on-screen UI. The 64-VQFN package's small footprint fits inside handheld enclosures, and the industrial -40 C to +85 C range supports hospital and field-clinic environments. Note: medical certification is system-level; this MCU itself is not FDA-cleared.
Recommended
Multi-Protocol Sensor Hubs
The PIC32MX775F512HT-80I/MR aggregates UART, I2C, CAN, and SPI sensors into a single Ethernet or USB gateway. Five I2C buses support multiple sensor ICs without bus contention, while four UARTs bridge RS-485/Modbus devices. The 8-channel DMA engine handles simultaneous data streams without CPU interrupt load, and 64 KB SRAM buffers pre-aggregation payloads. The 64-VQFN 9x9 mm exposed-pad package allows compact PCB designs where the MCU sits at the heart of the sensor hub.
Recommended
Recommended Products Summary
Engineering reference data for PIC32MX775F512HT-80I/MR — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | PIC32MX775F512H-80I/MR | PIC32MX695F512HT-80I/MR | PIC32MX675F512HT-80I/MR | PIC32MX764F128HT-I/MR | PIC32MX570F512HT-50I/MR | PIC32MX440F512HT-80I/MR |
|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-VQFN (9x9) | 64-VQFN (9x9) - same | 64-VQFN (9x9) - same | 64-VQFN (9x9) - same | 64-VQFN (9x9) - same | 64-VQFN (9x9) - same | 64-VQFN (9x9) - same |
| Core / CPU Speed | MIPS32 M4K / 80 MHz | MIPS32 M4K / 80 MHz | MIPS32 M4K / 80 MHz | MIPS32 M4K / 80 MHz | MIPS32 M4K / 40 MHz | MIPS32 M4K / 50 MHz | MIPS32 M4K / 80 MHz |
| Flash / SRAM | 512 KB / 64 KB | 512 KB / 64 KB | 512 KB / 64 KB | 512 KB / 64 KB | 128 KB / 32 KB | 512 KB / 64 KB | 512 KB / 32 KB |
| USB OTG | Yes (FS OTG) | Yes (FS OTG) | No | No | Yes (FS OTG) | Yes | No |
| Ethernet MAC | 10/100 Mbit | 10/100 Mbit | 10/100 Mbit | No | 10/100 Mbit | No | No |
| CAN 2.0b | 2 | 2 | 2 | 2 | 2 | 2 | 0 |
| DMA Channels | 8 | 8 | 8 | 8 | 8 | 8 | 8 |
| Operating Temperature | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
Key Differentiators
- Integrated USB OTG plus Ethernet plus dual CAN in a single 64-VQFN device (vs PIC32MX440F512HT-80I/MR)
- Largest Flash/RAM in the 64-VQFN PIC32MX5/6/7xx family (vs PIC32MX764F128HT-I/MR)
- Industrial-grade operating temperature and mature 80 MHz M4K core (vs PIC32MX570F512HT-50I/MR)
Design Notes
The 64-VQFN (9x9 mm) package has an exposed thermal pad on pin 64. The PCB land pattern MUST include a central pad with at least 9 thermal vias (0.3 mm drill, 0.6 mm pitch) tied to the ground plane. Without this thermal path, the junction temperature can exceed 125 C at full 80 MHz operation with all peripherals active. Solder paste stencil should use a 0.127 mm (5 mil) thickness with a 1:1 aperture ratio for the central thermal pad to avoid voids above 25 percent.
USB D+/D- traces must be routed as a 90 ohm differential pair with no splits or test points in the middle of the run. Add a common-mode choke near the connector and place the 15 kohm pull-down on D+ and D- to ensure a defined high-speed idle state. For self-powered USB designs, drive D+ through a switchable pull-up (e.g., VBUS-detect GPIO) instead of the internal pull-up to avoid back-powering the host port when the device is unpowered.
Place a 1 uF + 0.1 uF bulk-decoupling pair on every VDD/VSS pin combination, with the 0.1 uF as close as physically possible to the IC pin (under 1 mm trace length). The analog AVdd/AVss pins must be filtered with a ferrite bead and a 10 uF + 0.1 uF pair, and the AGND pin should return to a clean analog ground island that joins the digital ground at a single point near the PCB power entry.
Supply voltage range is 2.3 V to 3.6 V. The PIC32MX775F512HT-80I/MR consumes roughly 70 mA at 80 MHz with all peripherals active, so the 3.3 V LDO must supply at least 100 mA plus margin for digital I/O sourcing. For USB bus-powered designs, ensure VBUS detection GPIO is wired before the regulator enable so the MCU can hold the USB PHY in high-Z until a valid VBUS is present.
Compliance Information
RoHS compliant per Microchip product page. Industrial temperature grade (-40 C to +85 C) but NOT AEC-Q100 qualified for automotive. Lead-free / matte-tin finish. Halogen-free status not explicitly stated in verified data; consult Microchip environmental compliance letter for confirmation.
