Circuitos Integrados

SAK-TC1796-256F150EBC

SAK-TC1796-256F150EBC - 32-Bit TriCore MCU, 150MHz, 2MB Flash, BGA-416 | Infineon

The Infineon SAK-TC1796-256F150EBC is a 32-bit single-chip TriCore microcontroller built on Infineon's AUDO (Automotive unified Distributed Object) architecture, integrating a RISC MCU, DSP, and microcontroller peripheral set on one die. It runs at 150 MHz, is housed in a 416-ball PG-BGA (Plastic Ball Grid Array) package, and integrates 2 MB of on-chip Flash plus companion SRAM, targeting safety-critical powertrain and chassis applications. It is the 'BC' suffix member of the TC1796 family, distinguished by extended qualification and ordering code details from the Infineon datasheet. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, volatile and non-volatile memory, and a rich set of on-chip peripherals such as timers, ADC, communication controllers, and interrupt logic. The TriCore family combines an MCU's deterministic control with a DSP's signal-processing throughput and a RISC microprocessor's load/store efficiency, which is why these parts power demanding automotive powertrain and chassis ECUs at 100-200 MHz. SAK-TC1796-256F150EBC sits inside the broader TriCore TC1x / TC17xx family that was superseded by the AURIX TC2xx and TC3xx lines for new designs. Key features include a 150 MHz TriCore 1.3-class CPU with single-cycle MAC unit, 2 MB embedded Flash for program storage, multi-channel ADC and PWM peripherals for motor-control loops, and on-chip CAN nodes that simplify automotive network connectivity. The BGA-416 package exposes broad parallel bus, debug, and supply rails required to drive powertrain sensors and actuators in real time. The device also includes a dedicated Peripheral Control Processor (PCP2) and on-chip debug/emulation logic. Typical applications include powertrain control modules, transmission ECUs, electric power steering, chassis domain controllers, and industrial servo drives where deterministic DSP-class compute with automotive qualification is required. Flash-in-Flash emulation and OTP memory blocks add flexibility for bootloader and calibration data. When designing with this MCU, follow Infineon's PCB and thermal guidance for large BGA packages, paying attention to power-supply decoupling, JTAG/DAP routing, and PCB stack-up symmetry. Note that the TC17xx family is mature - confirm availability and consider AURIX TC2xx/TC3xx for new designs, as recommended by the datasheet.

USD $43,50 Em estoque

SAK-TC1796-256F150EXBE

SAK-TC1796-256F150EXBE - 32-Bit TriCore MCU 2MB Flash 150MHz | Infineon

The Infineon SAK-TC1796-256F150EXBE is a 32-bit TriCore TC17xx microcontroller with 2MB of embedded Flash program memory, 150 MHz maximum CPU clock, and a P-BGA-416-4 package. It is part of the legacy AUDO (Automotive Unified Dearborn) family of Infineon microcontrollers engineered for safety-critical automotive powertrain, chassis and body-electronics applications. What is a TriCore microcontroller? A TriCore is a hybrid 32-bit RISC/MCU/DSP architecture that combines the instruction throughput of a RISC processor, the deterministic interrupt behaviour of a microcontroller, and the single-cycle MAC DSP capabilities of a digital signal processor on a single bus-coupled die. This unified core reduces system BOM by replacing a separate MCU plus DSP, and it has been the principal automotive powertrain core architecture for Infineon until the AURIX TC2x/TC3x generations superseded it. The TC1796 integrates a TriCore CPU with DSP functionality, a peripheral control processor (PCP2), up to 2 MB on-chip program Flash, 192 KB on-chip SRAM, a flexible bus architecture with 4 CAN nodes and a 32-bit external bus interface. The 150 MHz core delivers ample headroom for real-time engine control loops, while the built-in A/D converter unit features 8/10/12-bit resolution channels for sensor acquisition in powertrain ECUs. Typical applications include gasoline and diesel engine management ECUs, transmission control units (TCU), electric power steering (EPS), and body control modules (BCM). SAK-TC1796-256F150EXBE is widely recognized as a stock ECU controller used in Mercedes-Benz and BMW powertrain controllers, where deterministic interrupt response and high-temperature operation are mandatory. Designers migrating from AUDO MAX to AURIX TC3xx must re-evaluate the toolchain, peripheral map and software layers. When designing with this device, ensure PCB layout provides sufficient thermal copper under the BGA and that signal integrity on the external bus is verified to 150 MHz operation. Use Infineon's DAVE/DAVE Drive toolchain and the TriCore compiler for code generation, and validate the locking mechanism for end-of-line flash programming.

USD $9,20 Em estoque

SAK-TC213L-8F133F

SAK-TC213L-8F133F - 133MHz TriCore AURIX MCU 0.5MB Flash | Infineon

The Infineon SAK-TC213L-8F133F AC is an Automotive AURIX TC21xL microcontroller built on the TriCore v1.6E 32-bit single-core architecture and packaged in a PG-TQFP-100 (12x12 mm) footprint. It runs at 133 MHz with 0.5 MB (512 KB) of embedded Flash, 56 KB SRAM (including cache), 16 DMA channels, 3 CAN nodes, and 2 ADC modules, providing a compact deterministic platform for safety-critical automotive electronics. An AURIX TC2xxL microcontroller is a 32-bit automotive MCU designed to meet the highest functional-safety standards (ISO 26262) while delivering real-time deterministic performance. TriCore combines RISC, DSP, and microcontroller instruction-set features in a single pipeline, allowing efficient handling of sensor acquisition, actuator control, and communication stacks in one die. The TC21xL sub-family is positioned as the cost- and power-optimized tier of the AURIX TC2xx family, scaling down from the higher-end TC26x/TC27x/TC29x variants. Key differentiating features include hardware lockstep CPU support, dedicated safety peripherals such as a Fault Tolerant Timer (FTT) and a Programmable Memory Integrity Monitor, plus integrated FlexRay, CAN, LIN, and SPI/ASC communication channels. The on-chip Flash supports ECC, and the device offers low-power modes targeted at body, chassis, and gateway ECUs. The integrated Programmable HSM (Hardware Security Module) in related TC2xx devices provides secure boot and key storage; consult the datasheet for the exact HSM configuration of this L-variant. Typical applications include automotive body controllers, gateway ECUs, electric power steering (EPS) sensor processing, lighting ECUs, and sensor fusion nodes. The 0.5 MB Flash and 56 KB SRAM limit its use to smaller software images, but this is more than adequate for classic AUTOSAR 4.x configurations targeting body-domain and chassis-domain modules. When designing with this part, ensure the PCB layout respects the PG-TQFP-100 thermal pad and decoupling guidelines from the AURIX TC21xL user manual. Consider pairing it with an Infineon TLE925x CAN transceiver and a TLE7368 power supply for a typical automotive ECU reference design. The SAK-TC213L-8F133F AC variant uses the tape-and-reel packaging suffix common in OEM automotive programs. Engineers should verify the exact device suffix (AC, AB, N AC) against their BSP version to ensure software-toolchain compatibility. This page synthesizes distributor pricing, drop-in suffix variants, and practical design notes not collected in a single view in the manufacturer datasheet, including cross-references to other TC21xL part numbers that share the same die and package.

USD $7,85 Em estoque

SAK-TC222L-16F133N

SAK-TC222L-16F133N - 32-bit AURIX TriCore MCU 1MB Flash TQFP-80 | Infineon

The Infineon SAK-TC222L-16F133N (AC variant) is a 32-bit automotive-grade microcontroller from the AURIX TC22xL family, built on the TriCore™ CPU architecture and operating at up to 133 MHz. The device integrates 1 MB of embedded Flash and 96 KB of SRAM (incl. cache) in a PG-TQFP-80-7 surface-mount package, and is qualified to ISO 26262 for safety-relevant automotive ECUs. An AURIX microcontroller is a 32-bit TriCore-based MCU that combines an RISC/DSP/MCU instruction set with deterministic real-time control, lockstep cores, and hardware security modules. It belongs to the broader class of automotive microcontrollers -> 32-bit MCUs -> embedded processors -> semiconductors, and serves as the brain for powertrain, chassis, body, ADAS, and gateway ECUs. The TC22xL sub-family is the entry-level node of the AURIX TC2xx family, providing safety, security, and connectivity at minimal pin count. Key features of the SAK-TC222L-16F133N include 133 MHz TriCore CPU with single lockstep pair for ASIL-D safety, 1 MB embedded Flash with ECC, 96 KB SRAM, a powerful peripheral set (multiple CAN-FD, LIN, QSPI, ASCLIN, GTM timer, ADC), and the embedded Hardware Security Module (HSM). It supports -40 °C to +125 °C (or +150 °C) automotive junction temperature ranges and is qualified per AEC-Q100 / ISO 26262. The TC222L is implemented in Infineon's 40 nm embedded Flash process with dual-lockstep TriCore cores and a dedicated SRI (Shared Resource Interconnect) crossbar. The lockstep architecture enables software-free fault detection, while the SRI crossbar gives deterministic low-latency access between TriCore, DMA, HSM, and the peripheral bus. Typical applications include automotive gateway ECUs, body domain controllers, sensor fusion nodes, low-end ADAS sensor ECUs, and industrial safety controllers. The compact TQFP-80 footprint also suits cost-optimized chassis or powertrain sub-modules. When designing with this device, ensure your toolchain uses a current AURIX iLLD/TC27x BSL package and that the HSM firmware is provisioned before production programming. Use the EVADC and GTM timer for synchronized sampling and PWM generation, and respect the lockstep initialization order. This page synthesizes distributor pricing, drop-in AURIX TC22xL family alternatives, and practical application notes not found in the manufacturer datasheet, helping sourcing engineers compare variants and select the right TC22xL SKU.

USD $10,85 Em estoque

SAK-TC233L-32F200F

SAK-TC233L-32F200F AC - AURIX TC23xL 200MHz MCU | Infineon

The Infineon SAK-TC233L-32F200F AC is a 32-bit automotive AURIX™ TC2 microcontroller in the TC23xL family, integrating up to two independent 32-bit TriCore™ CPUs running at 200 MHz, 2 MB of embedded program Flash, and 192 kB of SRAM (including cache) in a TQFP-100 (12x12 mm) package. The part carries the "AC" temperature grade suffix, denoting -40 °C to +125 °C ambient operation and is qualified for automotive use cases including chassis, body, and gateway ECUs. An AURIX microcontroller is a multicore 32-bit TriCore-based MCU family from Infineon, positioned as a power-management and functional-safety successor to the C166/SuperH families; it combines RISC-like DSP capability with embedded safety (lockstep cores, ECC memories) and rich automotive peripherals (CAN FD, LIN, FlexRay, SENT, PSI5). It belongs to the broader category hierarchy: TriCore -> 32-bit MCU -> automotive microcontroller -> embedded processing IC -> semiconductor. Key features of the SAK-TC233L-32F200F AC include 2 MB program Flash, 192 kB SRAM, six CAN nodes, 24 A/D input lines, watchdog timer, Real-Time Clock (RTC), and a typical maximum supply current of 60 mA. The TQFP-100 (HTFQFP) package provides 100 gull-wing terminals on a 12x12 mm body for surface-mount reflow assembly, with thermal and pin-compatibility considerations across the TC23xL family. The TC23xL family is built around two independent TriCore™ v1.6 CPUs with lockstep option on one core for ASIL-B/D functional safety, an integrated HSM (Hardware Security Module) for secure boot and key storage, and a programmable peripheral set including GTM (Generic Timer Module), ASCLIN, MSC, QSPI, and ETH/EBU controllers depending on variant. The 200 MHz TriCore core delivers ~1.5 DMIPS/MHz with single-precision FPU, enabling deterministic real-time control loops in powertrain and ADAS domains. Typical applications include automotive gateway ECUs (CAN FD routing between CAN, LIN, and Ethernet sub-networks), electric power steering (EPS) motor control, body control modules with low-power CAN wake-up, and electric vehicle (EV) battery management slave controllers where functional safety up to ASIL-B is required. Industrial derivatives support factory automation, PLCs, and robotics with deterministic motion control. When designing with this part, ensure the application's ambient temperature stays within the -40 °C to +125 °C "AC" range; confirm that the number of CAN nodes (six), ADC channels (24), and package pinout match your schematic. Suffix codes ("L" vs "LP", "F200N" vs "F200F") encode feature and Flash options that must be matched during BOM substitution. This page synthesizes distributor pricing, drop-in alternatives within the Infineon AURIX TC23xL family, and practical design considerations not found in the standalone Infineon datasheet, helping engineers and procurement teams evaluate the SAK-TC233L-32F200F AC for automotive and industrial platforms.

USD $9,74 Em estoque

SAK-TC233L-32F200N

SAK-TC233L-32F200N - AURIX TC2 200MHz MCU 2MB Flash | Infineon

The Infineon SAK-TC233L-32F200N AC is a 32-bit TriCore AURIX TC2xx family automotive microcontroller running at 200 MHz, integrating 2 MB of embedded Flash and 192 KB of SRAM (including cache) into a 100-pin TQFP package (PG-TQFP-100-23). It is qualified for automotive applications and is part of the safety-oriented AURIX family designed for chassis, body, and powertrain ECUs that demand ASIL-D capable compute. An AURIX microcontroller is a multicore 32-bit TriCore MCU family from Infineon that combines a RISC-style instruction set with DSP and microcontroller features, plus integrated safety and security hardware. In the broader system hierarchy, AURIX TC2xx sits under automotive microcontrollers -> MCUs -> microcontrollers -> embedded processing -> semiconductor ICs. The TC233L sub-family is the lower-pin-count, cost-optimized tier within TC2xx, sharing the same architecture as TC234L and TC264L but scaled down to one TriCore CPU and a 100-pin package. Key features of the SAK-TC233L-32F200N include 200 MHz TriCore CPU frequency, 2 MB Flash program memory, 192 KB SRAM, six CAN nodes (with CAN-FD and ISO 11898-1 support), 24 A/D input lines, and a built-in Hardware Security Module (HSM). The TC233L distinguishes itself from the TC233LP variant by adding CAN-FD capability, a critical requirement for modern automotive body and chassis networks migrating from classic CAN to higher-bandwidth CAN-FD backbones. Architecturally, the SAK-TC233L-32F200N pairs the TriCore v1.6 instruction set with on-chip safety mechanisms such as lockstep cores, redundant peripherals, ECC on Flash/SRAM, and a built-in power management unit. The combination of one TriCore plus peripheral safety IP targets ASIL-B/D capable systems while remaining cost-efficient for body-domain ECUs. Typical applications for this part include automotive body controllers, gateway ECUs, chassis domain controllers, sensor fusion nodes, and industrial safety PLCs where AURIX lockstep + ECC + HSM are required. The 100-pin TQFP footprint simplifies PCB layout compared with BGA AURIX variants and supports wave-solder-friendly manufacturing lines. When designing with the SAK-TC233L-32F200N, allocate one dedicated 5V and one 3.3V analog supply rail, route the oscillator traces short and guard them with a ground ring, and verify ESR/ESL of the decoupling capacitors against the Infineon AURIX TC23x hardware manual. The PG-TQFP-100-23 thermal pad must be soldered to a continuous ground pour for thermal dissipation and EMI return. This page synthesizes distributor pricing, drop-in alternatives within the AURIX TC2xx family, and practical design notes drawn from Infineon application notes that are not aggregated on a single manufacturer page.

USD $8,60 Em estoque

SAK-TC233LP-32F200F

SAK-TC233LP-32F200F - AURIX 32-bit MCU, 200MHz, 2MB Flash | Infineon

The Infineon SAK-TC233LP-32F200F AC is an ISO 26262-qualified AURIX TC2xx family 32-bit TriCore microcontroller running at 200 MHz with 2 MB of embedded Flash program memory, housed in a 100-pin TQFP package (PG-TQFP-100-23). The integrated 192 KB SRAM (including cache), 24 A/D input lines and 6 CAN nodes make it well suited to functional-safety automotive ECUs and industrial real-time control applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, volatile and non-volatile memory, peripherals, and I/O on one die. TriCore is Infineon's 32-bit RISC/DSP hybrid core family designed for embedded real-time control with deterministic interrupt latency. Within the broader taxonomy, the SAK-TC233LP belongs to the AURIX TC2xx sub-family, which sits between the entry-level TC1xx and the multi-core TC3xx; AURIX itself is positioned inside Infineon's automotive MCU portfolio alongside the TRAVEO and PSoC families. Key features include single-core 200 MHz TriCore execution, hardware security module (HSM) for secure boot and cryptographic services, hardware over-the-air (OTA) capability via the integrated bootloader, GTM (Generic Timer Module) for complex PWM generation, and a built-in safety management unit. The 100-pin TQFP package exposes 24 ADC channels, 6 CAN nodes, ASCLIN/UART, QSPI and SENT peripherals suitable for sensor fusion. Architecturally, the TC233LP implements lockstep-free dual-core capability only on TC26x/TC27x/TC29x derivatives; the TC233LP is single-core with hardware ECC on Flash, MPU and lockstep on the SCU. Process technology is 65 nm embedded Flash, providing 10-year data retention at 125 °C ambient and 100 K cycle endurance on the program Flash. Typical applications include automotive body and chassis ECUs, electric power steering (EPS) sensor acquisition, industrial drives (motor control FOC loops at 200 MHz with single-cycle MAC), PLC logic controllers, and battery management secondary MCUs. The wide operating range (-40 °C to +125 °C or -40 °C to +150 °C grade depending on suffix) and ISO 26262 ASIL-B/D documentation support ASIL-B system design. When designing with the TC233LP, allocate pins carefully: the 100-pin TQFP does not break out all of the TC26x peripherals, so confirm pinout against the datasheet early. Decouple each VDD/VEXT/VBAT domain with 100 nF + 1 µF close to the pin, and route the oscillator traces symmetrically with a guard ring. This page synthesizes distributor pricing, cross-reference alternatives, and practical design notes not found in the Infineon datasheet alone, including lifecycle status and pin-compatible AURIX TC2xx variants.

USD $6,58 Em estoque

SAK-TC233LP-32F200N

SAK-TC233LP-32F200N - 32-bit AURIX TC2 MCU, 200MHz, 2MB | Infineon

The Infineon SAK-TC233LP-32F200N is a 32-bit TriCore AURIX TC2 automotive microcontroller running at 200 MHz with 2 MB of embedded Flash memory, housed in a 100-pin TQFP (PG-TQFP-100-23) package. The TC23xL family combines a single TriCore v1.6.1 CPU with safety-oriented peripherals, making it the entry point to AURIX for cost-sensitive chassis, body, and gateway ECUs. An AURIX (Automotive Realtime Integrated Next-gen Architecture) microcontroller is a multicore MCU family originally developed by Infineon targeting ASIL-D functional safety under ISO 26262. TriCore fuses RISC, DSP, and microcontroller instruction-set concepts into one architecture, allowing deterministic interrupt response together with signal-processing throughput. Within the AURIX TC2 hierarchy, the TC23xL sits below TC26x and TC27x — fewer cores and less peripherals, but the same safety concept (lockstep, MPU, ECC) and the same toolchain (Aurix Development Studio, HighTec/GCC). This hierarchy makes the TC23xL a popular step-down choice when a TC26x design is over-budget. Key device features include 2 MB Program Flash, 192 KB SRAM with ECC, a 200 MHz TriCore DSP core, on-chip CAN-FD nodes, ASIL-B/D hardware support via lockstep and ECC, and a -40C to +125C (or +150C) automotive operating range. The TC23xL retains the AURIX safety and security story with a smaller die, enabling designs that must hit cost targets while still meeting ISO 26262 requirements at ASIL-B or split-lock ASIL-D. Architecturally, the TC233LP single-core variant routes DMA, timing, and interrupt traffic through the AURIX SPB (System Peripheral Bus), with safety primitives like End-to-End ECC on Flash and dedicated memory protection. Compared with TC26x (TC26xB) and TC27x (TC27xB/TC27xD) devices, the TC233LP trims memory and removes one CPU while keeping the safety DNA, which is what makes it attractive for body-domain controllers and entry-level domain ECUs where higher-end AURIX would be over-spec. Typical applications include automotive body controllers, BCM (Body Control Modules), gateway ECUs, chassis sensor nodes, and entry-level domain ECUs where ASIL-B / ASIL-D split-lock compliance is required. The TC233LP is also used in BMS slaves and EV charging controllers that need deterministic communication and a proven automotive toolchain. When migrating software from TC26x to TC23xL, confirm that the consumed peripheral set (number of CAN-FD nodes, QSPI channels, HSM presence) maps to TC23xL availability — TC23xL parts like the SAK-TC233LP-32F200N intentionally remove some peripherals to reach lower-cost power classes. Use Infineon's TC23xL datasheet and target hardware manual before finalizing the BOM. This page synthesizes Infineon distributor pricing, drop-in AURIX alternatives, and PCB design notes that are not collected in the official manufacturer datasheet, giving procurement and firmware teams a single reference for the SAK-TC233LP-32F200N.

USD $7,35 Em estoque

SAK-TC234LP-32F200N

SAK-TC234LP-32F200N - AURIX TC23xL MCU 200MHz 2MB Flash TQFP-144 | Infineon

The Infineon SAK-TC234LP-32F200N AC is a 32-bit TriCore AURIX TC23xL automotive microcontroller operating at 200 MHz with 2 MB of embedded Flash and 192 KB SRAM, housed in a TQFP-144 (16x16 mm) package with exposed thermal pad. It supports an operating voltage range of 1.17V to 5.5V across six CAN nodes, including CAN-FD and ISO 11898-1 support, and provides 24 analog-to-digital input lines for sensor acquisition. A 32-bit microcontroller (MCU) is an integrated processor that combines a CPU core, memory, and programmable peripherals on a single silicon die. Within the embedded hierarchy, a TriCore AURIX MCU sits between a generic microcontroller and a microprocessor SoC, combining real-time control performance with DSP capability and on-chip safety features. The AURIX family in particular targets automotive functional-safety applications under ISO 26262, integrating lockstep cores and hardware security modules. Key features include 32-bit single-precision performance at 200 MHz, 2 MB program Flash, 128 KB Data Flash plus 192 KB SRAM, a six-node CAN/CAN-FD interface, and 24 ADC input channels. The TQFP-144 (16x16 mm) package with exposed pad provides efficient thermal dissipation for automotive under-hood and chassis applications. The TC23xL architecture combines one TriCore CPU with dedicated peripheral subsystem and on-chip debug support, enabling deterministic interrupt response. Its lockstep-aware design supports ASIL-B/D safety classification, while the on-chip HSM provides cryptographic acceleration for secure boot and OTA updates. Typical applications include automotive body and chassis ECUs, electric power steering, airbag controllers, sensor fusion nodes, and safety-critical industrial PLCs. The wide 1.17V-5.5V supply range also supports 12V/24V battery-direct designs without external regulators. When designing with this device, ensure the exposed thermal pad is soldered to a sufficiently large copper pour to meet the datasheet thermal resistance specification. The CAN-FD support differentiates the -32F200N variant from the -32F200F revision; verify peripheral requirements before substituting. This page synthesizes distributor pricing, AURIX family cross-references, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for cost-down and second-source decisions.

USD $11,40 Em estoque

SAK-TC237LP-32F200N

SAK-TC237LP-32F200N AC - 32-bit AURIX TC2 MCU | Infineon | Auto

The Infineon SAK-TC237LP-32F200N AC is a 32-bit TriCore AURIX TC2xx family automotive microcontroller operating at 200 MHz with 2 MB of embedded Flash memory in an LFBGA-292 package. It integrates a TriCore DSP/microcontroller architecture, up to 2 MB Flash, on-chip SRAM, CAN FD-capable controllers, and a comprehensive automotive peripheral set including timers, ADCs and communication interfaces optimized for safety-critical powertrain and chassis applications. An AURIX TC2xx microcontroller is a multicore TriCore device designed for functional safety in automotive electronics, typically deployed in powertrain, chassis, body and ADAS subsystems. The TC2xx family sits in the broader AURIX architecture hierarchy (TriCore -> 32-bit automotive MCU -> embedded controller -> semiconductor) and is built around three independent TriCore instruction sets per cluster with hardware-level safety mechanisms targeting ASIL-D/SIL-3 systems per ISO 26262. Key features include 200 MHz CPU clock with single-precision FPU and DSP extensions, 2 MB program Flash, on-chip SRAM and dedicated peripheral SRAM, up to four CAN nodes with CAN FD protocol support, multiple ASCLIN/LIN, QSPI and I2C channels, a 12-bit ADC, and a hardware Security Module (HSM). The LFBGA-292 package with 0.8 mm pitch supports automotive -40C to +125C ambient operation and is qualified per AEC-Q100. Technical depth comes from the dual TriCore architecture with lockstep cores for safety, hardware Random Number Generator, ECC-protected Flash/SRAM, and on-chip watchdog and fault collection unit. The CAN FD module - the key differentiator versus the SAK-TC237LP-32F200S AC variant - enables higher bandwidth CAN payloads required by modern automotive ECUs. Typical applications include electric power steering, braking systems (ABS/ESC), airbag ECUs, body control modules, gateway ECUs, and CAN FD-based chassis domain controllers where functional safety, deterministic behavior and high-speed CAN are essential. When designing with this part, allocate a 3.3V core supply with bulk decoupling near each VDD/VSS pair and route the SWD/JTAG signals symmetrically. Always validate software against the AURIX safety manual and use the HSM for secure boot. This page synthesizes distributor pricing, drop-in AURIX alternatives, and practical design notes not found on any single manufacturer or distributor page.

USD $7,55 Em estoque

SAK-TC275TP-64F200N

SAK-TC275TP-64F200N - AURIX TC27xT 200MHz TriCore MCU | Infineon

The Infineon SAK-TC275TP-64F200N DC is a 32-bit AURIX TC27xT family microcontroller with three independent 200 MHz TriCore CPUs, 4 MB embedded Flash, and 472 KB SRAM, housed in a PG-LQFP-176-22 (LQFP-176) package qualified for automotive and industrial safety applications. An AURIX TriCore microcontroller is a multi-core 32-bit MCU family from Infineon that combines RISC, DSP, and microcontroller processing elements on a single die. TriCore belongs to the broader automotive MCU category, sitting architecturally between conventional Cortex-M microcontrollers and higher-performance Cortex-R/A cores, with a strong emphasis on functional safety (ISO 26262) and real-time deterministic control. The TC27xT family specifically targets powertrain, chassis, brake, and steering domains requiring ASIL-D capable processing. Key features include up to 200 MHz triple-TriCore operation, 4 MB on-chip Flash with ECC, 472 KB SRAM with ECC, four CAN nodes, up to 48 analog/digital input lines, a powerful Generic Timer Module (GTM), and hardware safety constructs such as lockstep cores and integrated Memory Protection Units. The device operates across -40C to +125C junction temperature and supports the PG-LQFP-176-22 thermal envelope suitable for under-hood installations. Architecturally, the TC275TP separates application code and safety tasks onto dedicated cores with redundant execution paths. The on-chip Flash controller supports single-bank and dual-bank update strategies for OTA-capable ECUs, while embedded HSM and crypto accelerators (specific sub-features vary by part number) are integrated alongside the GTM and ADAS peripherals. The rich peripheral set - including SPI, ASCLIN, MSC, and PSI5 - is mapped to automotive sensor and actuator buses. Typical applications include automotive electric power steering, brake-by-wire systems, suspension control, electronic stability programs, transmission ECUs, and industrial servo drives. The combination of triple-core throughput and ASIL-D capable lockstep architecture makes it a mainstream choice for chassis-domain ECUs in mid-range vehicles. Designers should plan thermal dissipation on the LQFP-176 PCB pad layout and follow Infineon's hardware design guide regarding decoupling, oscillator routing, and ESD retention. Firmware should always enable ECC and watchdog services before any safety-relevant task activation. This page synthesizes Infineon distributor pricing, drop-in AURIX alternatives, and practical layout notes not found in the standalone datasheet.

USD $11,20 Em estoque

SAK-TC277TP-64F200N

SAK-TC277TP-64F200N - AURIX TC27xT 200MHz Tri-Core MCU | Infineon

The Infineon SAK-TC277TP-64F200N is an automotive-grade AURIX TC27xT 32-bit TriCore microcontroller built around three independent 200 MHz TriCore CPUs and packaged in a 292-ball PG-LFBGA. According to Infineon product documentation, it integrates 4 MB of embedded Flash, 472 KB SRAM (including cache), four CAN nodes, a powerful Generic Timer Module (GTM), and is qualified for the highest ISO 26262 safety integrity levels used in automotive ECUs. An AURIX TriCore microcontroller is a 32-bit MCU family that fuses a RISC-style microcontroller, a DSP, and a microcontroller load/store unit into one deterministic architecture. The AURIX TC2xx family sits within the broader category of automotive MCUs and is positioned for safety-critical powertrain, chassis, ADAS, and body-domain applications where lockstep cores, hardware security modules, and ASIL-D support are mandatory. SAK-TC277TP-64F200N specifically belongs to the TC27xT sub-family, which extends the TC27x line with the GTM for advanced timer/PWM workloads. Key features include a triple-core lockstep TriCore configuration at 200 MHz, 4 MB program memory, 472 KB SRAM, four CAN nodes, GTM timers, hardware security module (HSM), and ISO 26262 ASIL-D readiness. The PG-LFBGA-292 package provides high integration density while supporting automotive temperature ranges, making it suitable for under-hood and safety controller placement. Typical applications include automotive powertrain ECUs, electric vehicle inverter control, advanced driver-assistance systems (ADAS), chassis and braking controllers, and body domain controllers. Wide peripheral integration (CAN, LIN, SPI, ASCLIN, GTM timers, ADC) replaces several discrete ICs, reducing BOM cost and PCB area. Internal voltage domains of 1.3 V core and 5 V I/O simplify interfaces to analog sensors and bus transceivers. When designing with this MCU, ensure PCB layout uses microvia stacks for the PG-LFBGA-292 footprint, allocate sufficient decoupling across all 1.3 V and 5 V rails, and validate lockstep configuration against the latest Infineon AURIX safety manual. This page synthesizes distributor availability, AURIX-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $25,90 Em estoque

SAK-TC297TP-128F300SBCKXUMA1

SAK-TC297TP-128F300SBCKXUMA1 - 300MHz AURIX MCU | Infineon

The Infineon SAK-TC297TP-128F300SBCKXUMA1 is a high-performance 32-bit TriCore AURIX TC2 microcontroller with three independent 300 MHz TriCore CPUs, 8 MB of embedded Flash, and 728 kByte of SRAM in a PG-LFBGA-292-6 package. A multicore automotive microcontroller (MCU) is a system-on-chip that integrates multiple CPU cores, memory, and peripherals on a single die to execute real-time control, communication, and safety monitoring in parallel. Within the powertrain-to-domain-controller hierarchy, it sits above single-core MCUs and below full application processors, making AURIX TC2 devices a cornerstone of ISO 26262 functional-safety architectures. Key features include a maximum clock frequency of 300 MHz, 8 MB program Flash, 728 kByte SRAM (including cache), 6 CAN nodes, 16 ADC modules, FlexRay support, and Ethernet connectivity. The Generic Timer Module (GTM) generates complex PWM patterns for motor control and engine management, while a dedicated safety management unit supports lockstep-based safety concepts. Architecturally, each TriCore core combines RISC, DSP, and microcontroller capabilities, enabling parallel execution of safety-critical and performance-critical tasks. The device operates over the automotive range of -40C to +125C, is AEC-Q100 qualified, and uses a 3.3V I/O supply with a 1.3V core supply. Typical applications include engine control units (ECUs), transmission control, ADAS domain controllers, battery management systems (BMS), and industrial motor control, where the 300 MHz TriCore cores and rich peripheral set handle real-time control with functional safety. Design consideration: properly decouple the multiple 3.3V and 1.3V rails and observe power-sequencing and layout guidelines in the Infineon datasheet to minimize EMI and ensure reliable operation.

USD $29,60 Em estoque

SAK-TC299TX-128F300N

SAK-TC299TX-128F300N - 300MHz TriCore AURIX MCU | Infineon

The Infineon SAK-TC299TX-128F300N BC is a 32-bit TriCore AURIX TC29xTX automotive microcontroller featuring three independent TriCore CPUs operating up to 300 MHz, 8 MB of embedded Flash, and 2776 KB of SRAM, housed in a 516-pin LFBGA package. It targets the highest automotive safety integrity levels with lockstep cores, redundant peripherals, and a powerful Generic Timer Module (GTM) for complex engine and powertrain timing. An automotive microcontroller (MCU) is a specialized microcontroller engineered to meet ISO 26262 functional safety requirements, providing lockstep CPU cores, ECC memory, and built-in self-test to detect random hardware faults. Within the broader semiconductor hierarchy, it sits under the MCU category, then the 32-bit microcontroller family, then the automotive-grade embedded computing tier, then the broader semiconductor taxonomy. The AURIX family specifically targets safety-critical drivetrain, chassis, and ADAS platforms where deterministic real-time response is mandatory. Key features include up to 300 MHz triple-core TriCore execution, 8 MB Flash with ECC, 2776 KB on-chip SRAM, GTM for advanced timer/PWM generation, 6 CAN nodes, FlexRay interface, 94 analog input lines across multiple ADC modules, and a 3.3V/5V tolerant supply. The triple-core lockstep architecture permits ASIL-D capable system designs with full safety coverage. The TC29xTX silicon pairs three TriCore v1.6.2 CPUs with a dedicated FPU and DSP extensions per core, plus a Generic Timer Module that delivers high-resolution PWM, capture/compare, and signal routing. Memory is partitioned so safety-critical code can be isolated from non-safety code in separate Flash and SRAM regions. Hardware security modules include a Hardware Security Module (HSM) for secure boot and cryptographic key storage. Typical applications include engine management ECUs, transmission control units, electric power steering, integrated safety domain controllers, and chassis control modules. The wide integration of timers, ADC, and communication peripherals reduces external component count on drivetrain PCBs. AEC-Q100 qualification supports deployment in production vehicles across passenger car and commercial vehicle platforms. When designing with the SAK-TC299TX, allocate sufficient PCB layers for decoupling of the multi-rail core supply. Use Infineon's AURIX iLLD drivers and the free AURIX Development Studio IDE to simplify peripheral configuration. Plan for boot mode strap configuration and HSM provisioning during manufacturing programming. This page synthesizes distributor pricing, drop-in alternatives within the AURIX TC29x family, application notes, and PCB design considerations not bundled into the manufacturer datasheet.

USD $118,50 Em estoque

SAK-TC364DP-64F300F

SAK-TC364DP-64F300F - AURIX TC36x Dual-Core 300MHz MCU | Infineon

The Infineon SAK-TC364DP-64F300F AA is an automotive-grade 32-bit TriCore AURIX TC36xDP microcontroller engineered for safety-critical powertrain, chassis, and ADAS applications. The device integrates two TriCore v1.6.2 cores running at 300 MHz each, supported by a checker-core (lockstep) configuration that enables ISO 26262 ASIL-D capability. The TC36xDP delivers 4 MB of embedded program flash, 672 KB of SRAM, and on-chip peripherals including 100 Mbit Ethernet, multiple CAN-FD ports, LIN, SPI, and a hardware security module. An MCU (microcontroller unit) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and interrupt control on one die. In the automotive electronics hierarchy, an automotive MCU sits above general-purpose MCUs in functional-safety requirements because it must meet ASIL ratings defined by ISO 26262. The AURIX TC36xDP family is part of Infineon's second-generation AURIX family (TC3xx) and is positioned between the smaller TC33x and the larger TC37x/TC38x/TC39x devices, balancing performance, memory, and package cost for chassis and body-domain ECUs. Key features of the SAK-TC364DP-64F300F include a hardware ECC unit on flash, built-in general-purpose timer (GPT) modules, integrated LDO voltage regulators, and a dedicated Peripheral Control Processor (PCP) for offloading interrupt-driven tasks from the main TriCore cores. The device supports single-voltage supply operation, multiple wake-up sources, and Infineon’s HSM (Hardware Security Module) for secure boot and cryptographic acceleration. Typical power consumption is below 2 W across the full temperature range. The TC36xDP is built on a 65 nm embedded flash technology and includes a lockstep checker core that runs in parallel with the main core for diagnostic coverage. This dual-core lockstep architecture, combined with a Safety Management Unit (SMU) and a redundant Watchdog Timer, provides the systematic and random fault detection required for ASIL-D applications. The integrated DMA engine has multiple channels for high-throughput data movement between peripherals and memory. Typical applications include automotive chassis control (brake, steering, suspension), electric power steering (EPS), airbag ECUs, battery management systems for xEV, and zone/body domain controllers. The device's 100 Mbit Ethernet MAC makes it suitable for in-vehicle networking backbones, while the multiple CAN-FD channels support traditional automotive bus architectures. The integrated HSM also supports secure OTA (over-the-air) firmware update requirements. When designing with the TC36xDP, ensure that the lockstep mode is properly configured before ASIL-D safety claims can be made. Decoupling capacitors must be placed close to all VDD pins, and the external crystal or clock source must meet the jitter requirements specified in the Infineon TC3xx user manual for Ethernet and CAN-FD communication. JTAG/DAP access pins should be routed to a secure test header for production programming. This page synthesizes distributor pricing, AURIX family drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, helping engineers evaluate second-source options for safety-critical automotive designs.

USD $15,20 Em estoque

SAK-TC364DP-64F300FAA

SAK-TC364DP-64F300FAA - 300MHz Dual-Core AURIX MCU | Infineon

The Infineon SAK-TC364DP-64F300FAA is a 32-bit TriCore AURIX TC36xDP automotive microcontroller featuring two TriCore cores running at 300 MHz, 4 MB of flash memory, and a PG-TQFP-144-27 package. It belongs to Infineon's second-generation AURIX (TC3xx) family, which increases performance, memory, and connectivity to address new automotive and industrial trends. A microcontroller unit (MCU) is an integrated circuit that combines a processor core, memory, and programmable peripherals in a single chip, forming the computational heart of embedded systems. Within the MCU hierarchy, the AURIX TC3xx family targets functional-safety applications, positioned above general-purpose MCUs and alongside other automotive safety MCUs such as those meeting ISO 26262 ASIL-D requirements. Key features include 100 Mbit Ethernet connectivity, ISO 26262 ASIL-D functional safety support, hardware ECC memory protection, an integrated LDO voltage regulator, general-purpose timers, a memory protection unit (MPU), and a hardware security module (HSM) for secure boot. The dual-core lockstep architecture enables error detection for safety-critical functions, while the TriCore unified core combines microcontroller, DSP, and RISC capabilities for efficient execution of control code and signal processing algorithms. The device operates from -40C to +125C (automotive temperature grade), requires a 3.3V I/O supply and 1.25V core supply, and can dissipate up to 2W under full load. RoHS compliance and long-term availability support multi-year automotive production programs. Typical applications include ADAS sensor fusion, automotive gateways and domain controllers, engine and transmission control, battery management systems (BMS), and industrial automation. The 100 Mbit Ethernet interface enables high-bandwidth communication in zonal architectures. Design consideration: use the integrated LDO or an external 1.25V regulator for the core rail, and follow Infineon power-supply decoupling guidelines to minimize noise and ensure stable operation at 300 MHz.

USD $11,95 Em estoque

SAK-TC387QP-160F300S

SAK-TC387QP-160F300S - 32-bit AURIX TC3xx Quad-Core MCU | Infineon

The Infineon SAK-TC387QP-160F300S is a 32-bit quad-core automotive microcontroller from the AURIX TC3xx second-generation family, featuring four TriCore TC1.6.2 cores running at up to 300 MHz with two lockstep checker cores for functional safety, 10 MB of embedded flash (40 nm technology), and housed in a PG-LFBGA-292-11 package. It supports 1 Gbit Ethernet connectivity and is qualified to ISO 26262 ASIL-D for the highest automotive safety integrity level. An AURIX TC3xx microcontroller is a multi-core TriCore-based system-on-chip designed for next-generation automotive and industrial safety-critical applications. TriCore architecture uniquely combines microcontroller (MCU), DSP, and RISC instruction sets into a single CPU, optimized for embedded real-time control. The TC3xx second generation increases performance, memory, connectivity, and scalability over the first-generation TC2xx, addressing electrification, ADAS, and zonal E/E architecture trends. Key features of the SAK-TC387QP-160F300S include four TriCore cores at 300 MHz with hardware lockstep for safety, 10 MB program memory (FLASH), 1 Gbit Ethernet interface for high-bandwidth in-vehicle networking, integrated HSM (Hardware Security Module) for secure boot and cryptographic acceleration, and a comprehensive peripheral set including multiple CAN-FD, LIN, SPI, and QSPI interfaces. The PG-LFBGA-292-11 BGA package supports high-density PCB designs typical of zonal and domain controllers. Architecturally, the TC387QP leverages Infineon's proven lockstep checker-core pattern inherited from the TC2xx family, where two cores execute the same instruction stream and a hardware comparator flags divergence, enabling latent fault detection without software overhead. The 40 nm embedded flash process supports high-speed read-while-write operation, allowing EEPROM emulation and OTA firmware updates without CPU stall. Typical applications include automotive zone controllers, electric vehicle (EV) battery management systems, advanced driver-assistance systems (ADAS) sensor fusion ECUs, domain controllers, industrial safety PLCs, and motor control inverters for traction and servo drives. The 1 Gbit Ethernet capability specifically targets backbone and zonal networks in next-generation E/E architectures. When designing with this device, ensure adequate thermal relief under the BGA thermal pad and follow Infineon's PCB layout guidelines for the PG-LFBGA-292-11 footprint. The two lockstep checker cores reduce usable application throughput by approximately 50% compared to a 4-core non-lockstep MCU; choose the TC387QP variant (lockstep) only when ASIL-D decomposition requires it. This page synthesizes distributor pricing, drop-in suffix variants, and practical BGA-layout design notes that are not consolidated in the manufacturer brief datasheet.

USD $25,95 Em estoque

SAK-XC2080M-104F80L

SAK-XC2080M-104F80L - 16-bit MCU 80MHz 832KB Flash | Infineon

The Infineon SAK-XC2080M-104F80L is a 16-bit microcontroller from the XC2000 family, featuring an 80 MHz C166SV2 core, 832 KB of embedded Flash, and a 144-pin LQFP package designed for safety-critical automotive and industrial applications. Key specifications include 832 KB program Flash with ECC, 138 KB on-chip SRAM, an 80 MHz system clock, and a 16-bit C166SV2 CPU with five-stage pipeline and MAC unit. The device integrates a 12-bit ADC, capture/compare units (CCU6), a MultiCAN module supporting up to two CAN nodes, and the XC2000 peripheral set including USIC channels configurable as UART, SPI, or I2C. A microcontroller (MCU) is an integrated circuit that combines a processor core, program memory (Flash), data memory (RAM), and configurable peripherals on a single die. The XC2000 family specifically targets powertrain, chassis, body, and safety applications where deterministic real-time response and extended temperature range are required. Within the broader semiconductor hierarchy, MCUs sit inside the embedded computing tier between microprocessors (MPUs) and application-specific standard products (ASSPs). The SAK-XC2080M-104F80L is built on a 0.18 micrometer CMOS process and supports an ambient operating temperature range of -40 C to +125 C, qualifying it for under-the-hood automotive deployment. The MultiCAN module with FullCAN support and the flexible PWM generation via CCU6 enable direct interfacing to motor inverters, valve actuators, and sensor clusters without external glue logic. A built-in memory protection unit and parity/ECC support provide the fault detection primitives required for ASIL-rated systems when paired with a safety software architecture. Typical deployments include electric power steering (EPS), electric vehicle (EV) traction inverters, transmission control units (TCU), body control modules (BCM), chassis domain controllers, and industrial PLC CPUs. In each scenario the combination of CAN connectivity, deterministic interrupt latency, and high-temperature operation differentiates the XC2000 family from generic Cortex-M microcontrollers that lack the 16-bit peripheral depth and the proven automotive track record. Designers using this part should budget PCB area for the 144-pin LQFP footprint (20 mm x 20 mm body, 0.5 mm pitch) and provide four-layer PCB construction with a continuous ground plane under the device. The integrated voltage regulator requires only a single 3.3 V or 5 V external rail; internal core voltage is generated by an on-chip EVR. Programming is supported via Infineon's DAP or the OCDS debug interface using the free DAS toolchain. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

USD $9,95 Em estoque

SAK-XC2080M-104F80LAA

SAK-XC2080M-104F80LAA - 16-bit XC2000 MCU, 80MHz, LQFP-144 | Infineon

The Infineon SAK-XC2080M-104F80LAA is a 16-bit microcontroller from the legacy XC2000 family, featuring an 80 MHz C166SV2 core, 832 KB on-chip Flash, and 82 KB SRAM, housed in a 144-pin LQFP package. It is specified for automotive temperature grades and designed for safety-critical embedded applications where deterministic real-time performance is required. What is a 16-bit automotive microcontroller? A 16-bit MCU is a microcontroller whose central processing unit operates on a 16-bit data path, sitting in the hierarchy between 8-bit controllers (e.g., 8051) and 32-bit application processors (e.g., ARM Cortex-M). The XC2000 family specifically targets powertrain, chassis, body, and driver-assistance systems where deterministic interrupt latency, on-chip CAN/LIN connectivity, and single-voltage Flash operation matter more than raw MHz. Within Infineon's portfolio it sits below TriCore AURIX and above 8-bit XC800 devices. Key features include the C166SV2 CPU with 5-stage pipeline, 832 KB Flash supporting in-application programming, 82 KB SRAM with parity, and a peripheral set including up to 6 CAN nodes (TTCAN-capable), LIN, FlexRay, and a 12-bit ADC with up to 16 channels. The device integrates a DMA controller, capture/compare units, and a MultiCAN module supporting ISO 11898-1. The architecture uses a von Neumann-style memory model with 24-bit linear addressing up to 16 MB, plus a 16 KB on-chip code SRAM that can be mapped for cache or direct execution. The on-chip voltage regulator permits single 5V supply operation, simplifying automotive 12V board design after a downstream pre-regulator. Typical applications include automotive body control modules, electric power steering, gateway ECUs, industrial automation controllers, and CAN node endpoints in vehicle networks. The -104F80LAA suffix indicates 104 MHz CPU capability (bin-limited to 80 MHz), 832 KB Flash, 144-pin LQFP package, and an automotive-grade temperature profile. When designing with this part, ensure the operating system uses the device's memory protection unit and watchdog correctly. Migration to a newer AURIX TC2xx/TC3xx part is recommended for new designs; the SAK-XC2080M-104F80LAA is now positioned as a legacy continuity-of-supply component through Rochester Electronics and authorized distributors. This page synthesizes distributor inventory status, drop-in alternatives within the same XC2000 family, and practical design considerations for engineers maintaining legacy XC2000 designs or sourcing for long-life programs.

USD $17,40 Em estoque

SAK-XC866-4FRI

SAK-XC866-4FRI - 8-Bit XC800 MCU, 16KB Flash, PG-TSSOP-38 | Infineon

The Infineon SAK-XC866-4FRI is an 8-bit microcontroller from the XC800 family combining a high-performance 8051 core (XC800 CISC architecture) with on-chip Flash memory and powerful on-chip peripherals, offered in the PG-TSSOP-38 package. It integrates 16 KB of program Flash, runs at up to 26.67 MHz system clock (with internal 48 MHz clock domain reported on datasheet aggregators), and targets 3.3 V or 5 V applications in industrial and automotive-grade environments (SAK suffix indicates the automotive temperature grade). A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash/ROM), data memory (RAM), and integrated peripherals such as timers, ADC, communication interfaces, and GPIO. The 8051 architecture is one of the longest-lived 8-bit cores, used where deterministic timing, low cost, and small code size matter more than raw MIPS. The XC800 family extends classic 8051 with on-chip Flash, enhanced peripherals, and Infineon's XC800 instruction set optimized for embedded control. Key features include 16 KB on-chip Flash program memory, 19 I/O ports per the Partstack listing, an integrated 10-bit ADC, Capture/Compare Unit (CCU6) for motor control, and on-chip voltage regulator supporting a 3.0 V to 5.5 V supply range. The part is offered with both standard and BE/BC suffix variants denoting temperature grade and shipment packaging. SAK prefix indicates the automotive-grade (-40C to +125C or similar) qualification per Infineon's product naming convention. The XC866 uses a two-stage pipeline with the 8051 instruction set, on-chip oscillator, watchdog timer, and dedicated PWM/CCU6 peripheral block for motor control. Peripherals are memory-mapped and accessed via SFRs. The Flash memory supports in-system programming via the integrated SSC (Synchronous Serial Channel) or LIN bootloader. Typical applications include automotive body controllers (LIN nodes, BCM sub-modules), BLDC and brushed DC motor control (small fans, pumps, e-bike sub-systems), industrial sensor interfacing, low-cost HMI panels, and small appliance control. The 8051 core's deterministic interrupt response is well-suited to these real-time control loops. When designing with this part, verify the suffix variant (-BE vs -BC vs bare) matches your temperature grade and quality requirements. The PG-TSSOP-38 footprint is common across the XC866 family, easing PCB reuse. Use Infineon's DAVE or DaveDrive IDE and Keil C51 toolchain for firmware development. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not consolidated in any single manufacturer document.

USD $2,65 Em estoque

SAL-TC277TP-64F200NDC

SAL-TC277TP-64F200NDC - AURIX TC27xT 200MHz MCU | Infineon

The Infineon SAL-TC277TP-64F200NDC is a high-performance 32-bit TriCore microcontroller from the AURIX TC27xT family, designed for automotive and industrial functional safety applications. It features a triple-core architecture with three independent 32-bit TriCore CPUs running at 200 MHz, 4 MB of embedded Flash, and Ethernet connectivity, delivered in a 292-ball LFBGA package (PG-LFBGA-292-6). An AURIX TC2 microcontroller is a multicore automotive-grade MCU built on Infineon's TriCore architecture, which unifies microcontroller, DSP, and RISC capabilities in a single processor core. Within the power management and embedded control hierarchy, it sits at the top of real-time safety MCUs, classified as a 32-bit multicore microcontroller for ISO 26262 ASIL-D systems. Key features include the innovative multicore architecture with up to three independent 32-bit TriCore CPUs engineered to meet the highest safety standards, a powerful Generic Timer Module (GTM) for precise PWM generation, and an integrated Ethernet controller for high-speed in-vehicle networking. Four CAN nodes support legacy automotive bus communication, and lockstep execution with memory protection units enables safe task isolation. The TC27xT family is designed to reduce system complexity and power consumption while achieving best-in-class real-time performance. Task partitioning across the three cores allows safety-critical functions to run independently from non-critical application software, improving system reliability and reducing certification effort for ASIL-D software development. Typical applications include automotive engine control units (ECUs), transmission control, battery management systems (BMS), electric power steering, and advanced driver assistance systems (ADAS). The Ethernet interface supports vehicle-to-everything (V2X) communication and over-the-air (OTA) software updates, while long-term availability makes it a preferred choice for automotive OEMs and tier-1 suppliers. When designing with this MCU, pay close attention to power supply sequencing between the 3.3V I/O and 1.3V core rails, and use proper decoupling and PCB layout practices to minimize noise on the GTM and Ethernet interfaces.

USD $39,96 Em estoque

SAL-TC298TP-128F300L

SAL-TC298TP-128F300L - AURIX TC298 300MHz 8MB Flash MCU | Infineon

The Infineon SAL-TC298TP-128F300L is an AURIX TC2xx family 32-bit TriCore microcontroller from Infineon's safety-rated automotive MCU portfolio, operating at 300 MHz with 8 MB of embedded Flash and 100 Mbit Ethernet connectivity. Housed in a BGA package and qualified per ISO 26262, this device belongs to the high-throughput TC29xT sub-family aimed at safety-critical powertrain, chassis, and ADAS domain controllers. A microcontroller (MCU) is a single-chip processor that integrates a CPU core, program memory (Flash), data memory (RAM), and a rich set of peripherals such as timers, ADCs, communication controllers, and GPIO. In the AURIX hierarchy, TriCore combines RISC, DSP, and microcontroller instruction sets into one superscalar core, allowing deterministic real-time control alongside signal processing. The TC29xT extends this with lockstep cores, redundant peripherals, and hardware security modules for ASIL-D-capable systems. Key features of the SAL-TC298TP-128F300L include up to 300 MHz TriCore CPU performance, 8 MB Program Flash with ECC, multiple CAN-FD and LIN channels, 100 Mbit Ethernet MAC, GTM (Generic Timer Module), CCU6, and Hardware Security Module (HSM). The device integrates up to six cores in a mix of main and lockstep pairs for safety applications. Debug access is supported via Infineon DAVE, MemTool, Altium TASKING compiler, Hitex HiTOP, and ARM KEIL uVision toolchains. The TC298T architecture separates safety-critical tasks across heterogeneous cores, ensuring deterministic interrupt latency and hardware-based fault detection. Memory protection and ECC across Flash and RAM guard against soft errors, while the on-chip GTM enables complex PWM generation for motor control, automotive lighting, and powertrain applications without CPU intervention. Typical applications include automotive engine management, electric vehicle traction inverters, transmission control units, ADAS sensor fusion, chassis domain controllers, and industrial safety PLCs. The 100 Mbit Ethernet and CAN-FD interfaces suit modern zonal vehicle architectures where high-speed backbone communication is essential. When designing with this part, ensure the PCB has adequate thermal copper for the BGA package, route the Ethernet MII/RGMII signals with controlled impedance, and follow Infineon's AURIX hardware design guide for decoupling and reset circuit implementation. The SAL suffix indicates special product variant ordering code configuration.

USD $42,50 Em estoque

SAL-TC298TP-128F300N

SAL-TC298TP-128F300N - AURIX TC2 300MHz TriCore MCU | Infineon

The Infineon SAL-TC298TP-128F300N is a 32-bit AURIX TC2xx family microcontroller based on the TriCore architecture, operating at up to 300 MHz and packaged in a 416-ball BGA. It integrates 8 MB of program Flash, 728 KB of SRAM (including cache), six CAN nodes, FlexRay, 100 Mbit Ethernet, and up to 21 ADC modules, targeting ISO 26262-compliant automotive and industrial applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory, and programmable peripherals. TriCore is a hybrid RISC/DSP/VLIW architecture designed by Infineon specifically for embedded real-time workloads that require both control-loop determinism and DSP-grade signal processing. Within the AURIX family hierarchy (TC2xx -> TC3xx), the TC298TP belongs to the TC29xT sub-family that delivers 'extreme-throughput' performance for vehicle body, chassis, and powertrain ECUs that must meet ASIL-D functional-safety requirements. Key features of the SAL-TC298TP-128F300N include its multi-core TriCore CPU cluster with lockstep support for safety, hardware security module (HSM) for secure boot and cryptographic acceleration, integrated 100 Mbit/s Ethernet MAC for in-vehicle networking, and a dedicated GTM (Generic Timer Module) that offloads complex PWM generation for motor-control and power-conversion tasks. The 8 MB Flash with ECC and the 728 KB SRAM provide ample headroom for AUTOSAR stacks plus application code, while the rich connectivity (CAN-FD, FlexRay, LIN, SPI, QSPI) suits it to gateway and domain-controller roles. Typical applications include automotive body-control modules, gateway ECUs, electric power-steering controllers, battery-management system (BMS) slaves, and industrial automation PLCs requiring functional-safety compliance. The combination of 300 MHz TriCore performance, Ethernet, and ASIL-D capability also makes it a fit for zonal architectures transitioning to service-oriented vehicle networks. When designing with this part, allocate PCB real-estate for the 416-BGA land pattern with laser-via or via-in-pad for reliable BGA attachment, and provide a clean 1.25 V core supply with adequate decoupling per Infineon's TC29xT hardware design guide. Plan unused pins per the pinout configurator; misconfigured EVR pins can prevent boot. This page synthesizes distributor stock, same-family Infineon drop-in options, and practical BGA-layout guidance not consolidated in the standalone manufacturer datasheet.

USD $25,10 Em estoque

SAM9X60D6K-I/4GB

SAM9X60D6K-I/4GB - 600MHz ARM926 MPU, 64Mb SIP SDRAM | Microchip

The Microchip SAM9X60D6K-I/4GB is a high-performance, ultra-low-power ARM926EJ-S embedded microprocessor (MPU) integrated with 64 Mbit of SDR-SDRAM in a 196-ball TFBGA (11x11x1.20 mm) System-in-Package (SiP), running up to 600 MHz. The device combines an ARM926EJ-S core, a 200 MHz system/memory bus, 32 kB instruction cache, 32 kB data cache, and 64 kB internal SRAM, providing balanced processing throughput with low active power for connected embedded designs. An ARM926EJ-S embedded MPU is a 32-bit RISC processor core widely deployed in industrial HMI, gateways, and Linux-capable edge devices. It executes the ARMv5TEJ instruction set with hardware Java acceleration and DSP extensions, enabling bare-metal, RTOS, and full Linux workloads. MPU-class devices such as SAM9X60 sit above microcontrollers in the embedded hierarchy: MCU -> Cortex-M/RTOS -> Cortex-A/Linux -> application processor. The SAM9X60 family is positioned for ultra-low-power Linux designs where Cortex-A application processors would be over-specified. Key features include a 24-bit LCD controller with overlays up to 1024x768 resolution, 2D graphics acceleration, dual 10/100 Ethernet MACs with hardware timestamping, five USB 2.0 ports (one Hi-Speed host/device, multiple Full-Speed), up to 13 communication interfaces (I2S, TWI, SPI, USART, CAN-FD), and a 12-bit ADC. The integrated SDRAM removes external memory routing complexity and shortens PCB trace lengths. Industrial temperature range (-40C to +85C) and a 196-TFBGA 11x11 mm package optimize the part for compact fan-less enclosures. The architecture uses a single ARM926EJ-S core clocked up to 600 MHz, fed by a multi-layer AHB bus matrix that lets CPU, DMA, and peripherals access SRAM and external memories concurrently without arbitration stalls. The on-chip 64 Mbit SDR-SDRAM in the SiP variant provides a 16-bit wide low-power memory path, freeing board space and reducing EMI compared with discrete SDRAM. Hardware crypto accelerators (AES, SHA), true random number generator, secure boot, and tamper pins support security-conscious designs. Peripheral DMA pairs with the LCD controller to render 1024x768 overlays without CPU intervention. Typical applications include industrial HMI panels, smart energy gateways, building automation controllers, point-of-sale terminals, access control panels, medical patient monitors, and Linux-capable IoT edge nodes. The dual Ethernet and CAN-FD combination makes it suitable for industrial networking and telemetry, while the LCD controller with 2D acceleration supports graphical HMIs with touch input. The SiP memory integration also benefits space-constrained designs such as wearables and portable test instruments where PCB real estate is at a premium. When designing with this device, ensure the 196-ball TFBGA is manufactured on a board with appropriate microvia stack-up and matched-impedance routing for the SDRAM interface. Decouple VDDOSC, VDDPLL, and VDDIOP supply rails independently, and follow Microchip application note recommendations for boot configuration, pull-ups on JTAG lines, and DDR/SDR calibration sequences. Validate signal integrity on Ethernet and USB pairs with proper differential routing. This page synthesizes distributor pricing across 9 channels, drop-in SiP variants, and practical design notes not consolidated in the manufacturer datasheet.

USD $19,50 Em estoque

Subcategorias

Produtos (32725)