Microcontroladores

Produtos (20.000+)

MC9S08QL4CTG - 8-Bit 20MHz 4KB MCU | NXP Semiconductors
MC9S08QL4CTG

MC9S08QL4CTG - 8-Bit 20MHz 4KB MCU | NXP Semiconductors

NXP Semiconductors MC9S08QL4CTG is an 8-bit S08 low-power microcontroller with a 20 MHz maximum operating frequency, 4 KB of flash program memory and a 16-pin TSSOP package. It operates from a 1.8 V to 3.6 V supply range, making it suitable for cost-sensitive, battery-powered and portable products that require compact embedded control. The device is listed by NXP as end of life, so new production designs should confirm migration requirements before committing to the MCU. An 8-bit microcontroller is a compact embedded-processing component that combines a processor core, program memory, data memory, clocking, and peripherals such as GPIO, timers, serial interfaces, and analog or timing functions on one integrated circuit. Within the broader semiconductor hierarchy, the MC9S08QL4CTG belongs to the S08 family of 8-bit microcontrollers and is designed for low-cost, low-power control tasks rather than high-performance computing. The principal device characteristics include an 8-bit architecture, 20 MHz maximum clock frequency, 4 KB flash storage organized as 4K x 8, and a 3 V-class operating range of 1.8 V to 3.6 V. Its 16-TSSOP package supports compact surface-mount PCB construction. The low-power positioning of the S08QL family makes the MCU applicable to portable instruments, simple appliance controls, low-cost sensor nodes, and compact user-interface assemblies where energy efficiency and component size are important. The MC9S08QL4CTG belongs to a family architecture that emphasizes low-power operation for embedded designs. Because the exact peripheral inventory, RAM capacity, pin assignments, and clocking options for this ordering code are not reproduced in the available product snippets, engineers should use the manufacturer datasheet and product page to confirm the resources required by the firmware and PCB design before release. Typical applications include battery-powered sensing equipment, compact appliance controllers, simple keypads, LED status indicators, and low-cost industrial monitoring modules. In each case, the 20 MHz processing rate provides adequate headroom for event-based control and basic serial communications, while the 16-pin package reduces board area compared with larger leaded or high-pin-count MCU packages. The main engineering consideration is lifecycle risk: NXP identifies MC9S08QL4CTG as end of life. Use the product page's discontinuation and replacement information to evaluate migration, and use the Request a Quote form on this page for current availability and sourcing support. This page also organizes the known electrical, package, lifecycle, and application information with engineering-oriented design guidance.

Cotação Contato
MC9S08QL4CTJ - 8-Bit 20MHz 4KB Flash MCU | NXP Semiconductors
MC9S08QL4CTJ

MC9S08QL4CTJ - 8-Bit 20MHz 4KB Flash MCU | NXP Semiconductors

The NXP Semiconductors MC9S08QL4CTJ is an ultra-low-power 8-bit S08 microcontroller with 4 KB of flash memory, a maximum stated operating frequency of 20 MHz, and a 20-pin TSSOP package. It is designed for space-constrained automotive and other low-power applications that require compact code storage, integrated analog peripherals, and integrated timers. The device operates across a stated 1.8 V to 3.6 V voltage range, making it suitable for battery-sensitive portable systems operating from low-voltage rails. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one package. The 8-bit S08 architecture provides a compact control platform for monitoring inputs, sequencing outputs, and managing simple communication or timing functions. In the system hierarchy, the MC9S08QL4CTJ is a general-purpose microcontroller, a semiconductor device, and a component within embedded control and power-management designs. The main specifications identify a 4 KB flash program memory, 4K x 8 organization, 20 MHz maximum operating frequency, and 20-pin TSSOP package. NXP describes the S08QL family as providing extreme energy efficiency for portable and battery-sensitive applications. Integrated timers and analog peripherals reduce the number of external components required in small automotive control modules, sensor interfaces, and compact embedded products. The 1.8 V to 3.6 V operating range supports designs using low-voltage power supplies while retaining a 20 MHz clock-rate option for faster peripheral processing. Because the MCU combines a processor, flash memory, timers, and analog functions, board design should account for stable supply voltage, correct decoupling, programming access, and unused-pin handling. The TSSOP package also requires adequate assembly clearances and a PCB footprint that matches the manufacturer's dimensional drawing. Typical uses include compact automotive body-control functions, battery-operated sensor nodes, simple motor-control tasks, and low-power monitoring products. The device can be selected when a small 8-bit controller, low-voltage operation, and 4 KB of flash are more important than a large application-specific peripheral set. Its 20-pin TSSOP format also helps reduce board area compared with larger controller packages. When choosing this MCU, verify the exact pin functions, programming method, electrical limits, and peripheral assignments in the manufacturer datasheet before layout release. This page consolidates the available manufacturer and distributor information and highlights practical selection considerations, application guidance, and sourcing information for engineers evaluating the MC9S08QL4CTJ. This product page also organizes replacement questions, package considerations, operating-range details, and commercial inquiry guidance into a compact engineering reference. For current availability and quotation, use the Request a Quote form on this page rather than relying on static marketplace pricing.

Cotação Contato
MC9S08QL8CTG - 8-bit 20MHz Low-Power MCU | NXP
MC9S08QL8CTG

MC9S08QL8CTG - 8-bit 20MHz Low-Power MCU | NXP

The NXP Semiconductors MC9S08QL8CTG is an 8-bit S08QL microcontroller with a 20 MHz operating frequency, 8 KB flash memory, 512 bytes of RAM, and a 16-pin TSSOP package. It operates from 1.8 V to 3.6 V and is designed for cost-sensitive, battery-sensitive, and portable systems that require low-power operation without a larger 32-bit control architecture. An 8-bit microcontroller is a compact control IC containing a processor core, program memory, data memory, clock circuitry, and peripherals on one package. The S08 family belongs to the broader hierarchy of microcontrollers, embedded processors, and semiconductor devices. MC9S08QL8CTG combines a small flash-memory footprint with energy-saving modes suited to products that spend substantial time waiting for external events. The QL8 device provides two ultra-low-power stop modes, low-power run and wait-for modes, a 6 microsecond wake-up time, an ultra-low-power external oscillator, and clock-gating registers for unused peripherals. These features help reduce energy consumption in battery-powered equipment while preserving fast recovery from sleep. Its 1.8 V to 3.6 V operating range also accommodates low-voltage supply designs. Within the S08QL family, the 20 MHz processor supports general embedded-control workloads, while 8 KB of flash provides room for application firmware. The 512-byte RAM supports working variables and stack operations, but designers should confirm interrupt depth, buffer requirements, and firmware size before committing the part to a new design. The 16-terminal TSSOP package supports compact, surface-mount PCB layouts. Typical applications include battery-powered sensors, compact appliance controls, low-cost remote controls, metering equipment, simple motor-control interfaces, portable accessories, and embedded timer or event systems. The part is particularly relevant when the system needs deterministic low-power behavior, uncomplicated firmware, and a compact package rather than high computational throughput or a large peripheral set. Designers should verify the complete pin function, programming method, clock options, and electrical limits in the manufacturer datasheet before layout release. Because the NXP product page identifies this exact orderable MPN as end of life, new production designs should also evaluate an active replacement rather than assume long-term availability. This page combines the manufacturer's product information, verified distributor listings, lifecycle status, package characteristics, low-power feature details, and a practical selection framework. It also identifies the distinction between the exact end-of-life MPN and possible same-family alternatives that require firmware, memory-capacity, and lifecycle review before substitution.

Cotação Contato
MC9S08QL8CTJ - 8KB Flash 20MHz 8-bit MCU | NXP
MC9S08QL8CTJ

MC9S08QL8CTJ - 8KB Flash 20MHz 8-bit MCU | NXP

NXP Semiconductors MC9S08QL8CTJ is an 8-bit S08 microcontroller with 8 KB of flash memory, a 20 MHz maximum clock rating, and a 20-pin TSSOP package. It operates across a 1.8 V to 3.6 V supply range and includes voltage detection and an internal clock source for cost-sensitive, low-power embedded systems. An 8-bit microcontroller is a compact processor architecture designed to execute control, sensing, and communication tasks with relatively simple firmware. The MC9S08QL8CTJ belongs to the S08QL low-power MCU family, where the S08 core combines deterministic control operation with energy-conscious features. Its position in the hierarchy is microcontroller, embedded processor, semiconductor, and integrated circuit. The principal benefits of this device include 8 KB of programmable flash, an 8-bit CISC-based S08 core, operation from a 1.8 V to 3.6 V supply, and a maximum clock frequency of 20 MHz. The internal clock source reduces external clock-component requirements, while voltage detection supports board-level monitoring and protection. The 20-pin TSSOP package also supports compact, surface-mounted PCB layouts. The MC9S08QL8CTJ is intended for applications where a compact controller must manage sensors, actuators, user inputs, and low-speed serial interfaces. Its 8 KB flash capacity is most useful for small control loops and tightly scoped firmware rather than graphics, extensive data storage, or protocol-heavy gateways. The 1.8 V to 3.6 V operating range suits battery-sensitive and energy-efficient portable products. Typical uses include battery-operated monitoring devices, simple industrial sensor nodes, compact appliance controls, security and access modules, and low-power industrial automation products. Its low-cost architecture and small flash footprint make it appropriate when the firmware performs direct control rather than intensive computation. PCB design should preserve the required power and decoupling structure around the TSSOP device while keeping sensitive routes away from fast-switching nodes. Firmware capacity should be monitored because the 8 KB flash also holds the boot code, application logic, constants, and configuration values. Confirm peripheral assignments and pin multiplexing against the manufacturer datasheet before finalizing the board layout. This page organizes the MC9S08QL8CTJ electrical characteristics, application guidance, compatibility limits, and procurement information into a concise engineering reference. It also distinguishes a verified same-family replacement from cross-package or functionally similar devices that are not true drop-in choices.

Cotação Contato
MC9S08RC16FG - 8-Bit 8MHz 16KB Flash MCU | NXP
MC9S08RC16FG

MC9S08RC16FG - 8-Bit 8MHz 16KB Flash MCU | NXP

The NXP Semiconductors MC9S08RC16FG is an 8-bit S08 series microcontroller operating at 8 MHz, with 16 KB of programmable flash memory in a 44-LQFP package measuring 10 mm by 10 mm. The device is designed for embedded control applications that require a compact microcontroller, nonvolatile program storage, and a moderate-pin-count surface-mount package. A microcontroller is a programmable integrated circuit that combines a processor core, memory, and peripherals into one component for controlling electronic systems. The S08 family belongs to the broader embedded-microcontroller hierarchy, where firmware executes from internal flash and interacts with sensors, switches, communications interfaces, and other external circuits. This role distinguishes the MC9S08RC16FG from passive components and from general-purpose processors intended for larger computing systems. The principal documented characteristics of the MC9S08RC16FG are its 8-bit architecture, 8 MHz operating frequency, and 16 KB flash capacity. The flash arrangement is identified as 16K x 8, meaning the program memory stores 16,384 eight-bit locations. These figures position the device for embedded products requiring moderate code space without the complexity of a larger controller. The 44-LQFP package also supports compact, high-density PCB layouts while exposing more I/O than a small-outline package. The S08 architecture is designed for cost-conscious embedded control, where deterministic control behavior, general-purpose I/O, and integrated nonvolatile program memory are more important than a large high-level operating-system footprint. The 8 MHz clock provides the execution basis for the controller, while the 16 KB flash region supports firmware storage and boot-oriented embedded routines. Detailed RAM organization, peripheral channels, voltage limits, and electrical timing must be confirmed in the manufacturer datasheet before a board design is released. Typical application directions include appliance controllers, small motor-control boards, digital keypads, industrial modules, sensor-interface products, and compact access-control equipment. In each case, the device can coordinate inputs and outputs through firmware while its flash memory retains the application program. The 44-LQFP footprint is especially useful when a design needs more external connections than a small 20-pin package can offer. Designers should verify the complete pin assignment, power requirements, clock options, programming method, and peripheral multiplexing before layout. The package drawing and pin descriptions in the manufacturer datasheet are the authoritative references for track routing and programming-header connections. A footprint based only on the 44-LQFP body size is incomplete unless pad dimensions, pin numbering, and exposed thermal-pad treatment are also confirmed. This product page consolidates the verified device identity, package information, source documents, sourcing guidance, and engineering-focused selection considerations. It also separates confirmed characteristics from parameters that require direct datasheet verification, helping engineers plan a design without overlooking memory, package, or cross-reference constraints.

Cotação Contato
MC9S08RC32FJ - 8-Bit 8MHz 32KB Flash MCU | NXP
MC9S08RC32FJ

MC9S08RC32FJ - 8-Bit 8MHz 32KB Flash MCU | NXP

The NXP Semiconductors MC9S08RC32FJ is an 8-bit S08 microcontroller operating at 8 MHz, with 32 KB of flash program memory and a 32-lead LQFP package measuring 7 mm by 7 mm. Its operating supply range is 1.8 V to 3.6 V, making it suitable for compact embedded systems that use low-voltage 3.3 V power rails. The MCU is identified as an S08-series device with 32 KB organized as 32K by 8 bits. A microcontroller is a programmable semiconductor that integrates a processor core, program memory, data memory, and peripherals into one device. The S08 architecture belongs to the broader category of 8-bit embedded microcontrollers, which are commonly used for control, sensing, and actuator-management tasks. At 8 MHz, the MC9S08RC32FJ provides deterministic processing capability for products where a low-cost, low-power controller is preferable to a more complex application processor. The MC9S08RC32FJ combines 32 KB of flash memory with an 8 MHz operating frequency in a 32-LQFP package. The 1.8 V to 3.6 V operating range supports direct operation from common low-voltage rails, while the 7 mm by 7 mm package provides a surface-mount solution for compact assemblies. Its 32-terminal gull-wing package also exposes more interface connections than a smaller 20-pin controller package, supporting practical external sensing, communications, and control connections. This commercial-temperature S08 microcontroller is positioned for embedded control designs that require an established 8-bit architecture and an adequate balance of flash memory, processing speed, and package size. The 32 KB program-memory capacity can hold application firmware, configuration logic, and control routines. Because the device is identified as an 8-bit MCU, software timing and interrupt handling should be evaluated against the workload rather than compared directly with 16-bit or 32-bit processors. Typical uses include small motor and relay controllers, building-control interfaces, appliance control panels, industrial sensing nodes, and compact consumer products. Its 8 MHz operating speed is appropriate for supervisory control loops, button and sensor management, status indication, and communications handling. Designs that require substantially more code space, higher processing throughput, or a different pin count should evaluate another MCU in the S08 family or a device from another embedded-controller architecture. The principal design consideration is ensuring that the LQFP footprint, pin assignment, flash requirement, voltage range, and peripheral configuration match the intended PCB. Use the pin-description table in the manufacturer datasheet when assigning tracks, and confirm the board's exposed thermal and manufacturing requirements before release. Firmware development should also account for the S08 peripheral configuration and memory map used by the selected software toolchain. This page organizes the available specifications, package information, practical application guidance, and confirmed family alternatives into one engineering reference. It also identifies unsupported electrical, timing, peripheral, and environmental details for verification against the manufacturer datasheet before a production design is released.

Cotação Contato
MC9S08RC60FG - 8-Bit 8MHz 60KB Flash MCU | NXP | LQFP
MC9S08RC60FG

MC9S08RC60FG - 8-Bit 8MHz 60KB Flash MCU | NXP | LQFP

The NXP Semiconductors MC9S08RC60FG is an 8-bit S08 microcontroller with an 8 MHz clock, 60 KB of Flash memory, and a 44-LQFP package measuring 10 mm by 10 mm. It is designed for embedded control applications that require deterministic digital control, compact packaged logic, and embedded program-and-data memory in one device. An S08 microcontroller is an 8-bit embedded-control platform within the broader hierarchy of microcontrollers, embedded processors, and semiconductor devices. The MC9S08RC60FG combines a byte-oriented processor core, Flash program memory, and integrated peripherals in a surface-mount package. This combination allows control logic, communications, and product-specific functions to be consolidated without requiring a separate external memory device when the application's requirements fit within the available resources. The headline device characteristics are an 8-bit processing architecture, an 8 MHz operating clock, and 60 KB of Flash memory. Its 44-LQFP package provides 44 externally accessible or assigned positions and is offered in a 10 mm by 10 mm physical format. The MC9S08RC60FG is therefore suited to compact embedded controllers where deterministic firmware execution, integrated nonvolatile storage, and moderate logic complexity are more important than high processor throughput. The S08 architecture is intended for embedded products in which peripherals and firmware can be assigned directly to application functions. Compared with a larger 16- or 32-bit processor, an 8-bit controller can provide sufficient computation for motor, display, appliance, and industrial-control tasks while preserving a straightforward programming model. The 60 KB Flash allocation provides meaningful firmware space for protocol handling, state machines, calibration data, and background routines, although final memory budgeting must include the linker map and boot-code requirements. Typical uses include appliance controllers, small motor-control boards, keypad and display interfaces, instrumentation, industrial modules, and low-cost embedded products. A design may use the MCU to read inputs, execute a control algorithm, update an output, and manage communication through its integrated peripherals. The 8 MHz clock supports straightforward event-driven firmware, while the available Flash supports more extensive application code than many compact 8-bit controllers. The principal design consideration is to verify the exact peripheral allocation, electrical limits, reset behavior, and programming configuration for the MC9S08RC60FG. Engineers should preserve the 44-LQFP land pattern, follow the manufacturer's decoupling and signal-routing guidance, and confirm the controller's unused-pin requirements. Review the complete pin-description and connection tables in the manufacturer datasheet before assigning every package terminal. This product page organizes the confirmed device identity, package, clock, memory, sourcing path, and engineering considerations into one engineering reference. It also distinguishes confirmed characteristics from parameters that require confirmation in the full manufacturer documentation, helping designers make a faster and safer component-selection decision.

Cotação Contato
MC9S08RC8CFG - 8MHz 8KB Flash 8-Bit MCU | Motorola | LQFP-44
MC9S08RC8CFG

MC9S08RC8CFG - 8MHz 8KB Flash 8-Bit MCU | Motorola | LQFP-44

The Motorola MC9S08RC8CFG is an 8-bit S08 CISC microcontroller operating at up to 8MHz, with 8KB of Flash memory and a 44-pin LQFP package measuring 10mm by 10mm. The device is intended for embedded control applications requiring modest processing throughput, on-chip Flash program memory, low-voltage operation, and a compact surface-mount package. Verified distributor listings identify the part as an S08 microcontroller with an 8KB Flash configuration and an operating voltage range of 2.5V to 3.6V or 1.8V to 3.6V depending on the source listing; engineers should confirm the exact electrical limits against the manufacturer datasheet before design release. A microcontroller is a programmable control component that integrates a CPU core, memory, and peripherals on one semiconductor device. The S08 family belongs to the broader embedded-controller hierarchy and is designed for compact control systems rather than high-performance computing. MC9S08RC8CFG combines an 8MHz maximum clock with 8KB Flash, making it appropriate for products that require moderate real-time control, local program storage, and a low component count without an external memory interface. The verified specifications identify the MCU as an 8-bit S08 device with 8KB Flash and a 44-LQFP package. The S08 architecture uses a CISC-style instruction set and is suited to embedded products requiring straightforward firmware control, GPIO handling, timers, serial communication, and analog or control functions, subject to the exact peripheral configuration in the manufacturer datasheet. The 44-pin package provides substantially more external connection options than small-outline packages, making the device practical for designs needing multiple I/O signals or mixed analog and digital functions. MC9S08RC8CFG can be considered for industrial controls, consumer appliances, instrumentation, motor and relay control, sensor interfaces, and compact embedded modules. Its 8MHz clock is generally sufficient for supervisory loops, keypad and display handling, communication management, and deterministic low-to-moderate-complexity control. The part is available through multiple distributors, and one verified listing reports an in-stock starting price of $1.4906, while another reports a price of $4.0627; prices should therefore be checked by quantity, condition, and authorized distributor inventory as of 2026-10-30. For PCB design, verify the exact pin assignments, exposed-pad requirements, decoupling recommendations, and operating-temperature limits in the MC9S08RC8 datasheet before layout release. Because the supplied search results do not include a complete manufacturer pin table, the pinout is intentionally left unavailable rather than presenting guessed pin numbers. Likewise, final peripheral counts, timer resources, ADC specifications, communication interfaces, and electrical timing characteristics require confirmation from the authoritative device documentation.

Cotação Contato
MC9S08RC8CFJ - 8-Bit 8MHz MCU with 8KB Flash | Motorola
MC9S08RC8CFJ

MC9S08RC8CFJ - 8-Bit 8MHz MCU with 8KB Flash | Motorola

The Motorola MC9S08RC8CFJ is an 8-bit S08 microcontroller operating at up to 8 MHz with 8 KB of programmable Flash memory in a 32-pin LQFP package measuring 7 x 7 mm. The verified distributor listing identifies the device as an S08 MCU with 8 KB (8K x 8) Flash and a 32-LQFP (7 x 7) package. Its combination of an 8-bit architecture, compact package and embedded Flash suits cost-sensitive embedded-control designs that require deterministic peripheral-driven operation rather than a high-performance application processor. An S08 microcontroller is a member of the 8-bit embedded-microcontroller hierarchy, combining a CPU core, Flash program memory, data memory, timers, communication interfaces and interrupt control in one integrated circuit. Compared with larger 16-bit or 32-bit MCU families, the MC9S08RC8CFJ provides a straightforward platform for motor control, appliance control, instrumentation and compact embedded products. Its role within an electronic system is to execute firmware, acquire external signals and coordinate actuators or communications. The principal verified features are an 8-bit processor operating at 8 MHz, 8 KB of Flash organized as 8K x 8, and a compact 32-LQFP package. The Flash memory provides space for application code and fixed firmware, while the low pin count supports space-constrained boards. Distributor availability data identifies stocked units from multiple sources, including 33,920 pieces reported by Wolfchip on December 24, 2025, although individual inventory levels can change rapidly. The S08 architecture is intended for embedded applications in which predictable I/O handling, compact PCB area and simple tool-supported development are more important than high computational bandwidth. The MC9S08RC8CFJ can serve as the central controller in a keypad interface, a small motor or relay controller, a sensor-processing module or a communication endpoint. Its Flash-based program model also allows firmware to be retained without an external program-memory device. Typical applications include industrial controls, consumer appliances, automotive accessories and compact instrumentation. In each case, the MCU can read sensors through its peripheral interfaces, execute control logic and update outputs without requiring a separate processor. The 32-LQFP footprint also simplifies transition from a larger prototype package to a production board when the pin count and thermal design remain suitable. The primary design consideration is to verify all electrical limits, pin multiplexing, clock configuration and peripheral assignments against the manufacturer datasheet before PCB release. Because the supplied verified data does not provide individual pin names, voltage limits, current ratings or memory-map details, those values are intentionally not guessed here. A reliable design should also include appropriate decoupling and a conservative operating strategy around temperature and supply-voltage limits. This page consolidates verified distributor specifications, current pricing references, strict same-package replacement guidance, comparison parameters and practical selection notes. It is intended to help engineers distinguish verified MC9S08RC8CFJ characteristics from unconfirmed device details and to identify the information that must still be checked in the authoritative datasheet before hardware release.

Cotação Contato
MC9S08RC8FG - 8MHz 8KB 8-Bit MCU | Motorola | Embedded
MC9S08RC8FG

MC9S08RC8FG - 8MHz 8KB 8-Bit MCU | Motorola | Embedded

Motorola, Inc. MC9S08RC8FG is an 8-bit S08 CISC microcontroller with an 8 MHz operating frequency, 8 KB of flash memory organized as 8K x 8, and a 44-LQFP (10 x 10 mm) package. The device supports 2.5 V and 3.3 V operation according to the verified distributor specifications. The MC9S08RC8FG is intended for embedded control applications where a compact 8-bit architecture, on-chip flash memory, and a 44-pin surface-mount package provide a practical combination of capability and board density. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. Within the product hierarchy, the MC9S08RC8FG is an embedded microcontroller, an 8-bit microcontroller, and specifically an S08 family device. The S08 core uses a CISC architecture and provides a direct software-driven path to compact embedded-control designs. As an 8-bit MCU, it is better suited to sequential control, sensing, and interface logic than to workloads requiring large memory capacity or high arithmetic throughput. The principal verified features are an 8 MHz S08 processor, 8 KB of flash memory, 8K x 8 memory organization, 2.5 V or 3.3 V operation, and a 44-LQFP package measuring 10 x 10 mm. These specifications make the MC9S08RC8FG appropriate for industrial control panels, compact instrumentation, appliance controllers, data-acquisition modules, and embedded peripheral controllers. The flash-memory configuration allows firmware to be programmed into the same package used in production without an external program-memory device. The 44-LQFP package provides 44 external connection points on a 10 x 10 mm footprint, making it useful for designs that require more I/O than a small-outline package can offer. The verified snippets do not state the complete peripheral list, RAM capacity, GPIO count, timer configuration, communication interfaces, temperature range, or electrical timing limits; these values must therefore be confirmed in the manufacturer datasheet before schematic capture or PCB release. MC9S08RC8FG is best used as a cost-conscious embedded controller when its S08 architecture, 8 KB flash budget, and 44-LQFP footprint fit the design. Engineers should verify the complete pin assignment and peripheral map against the applicable Motorola datasheet, especially when replacing a device with a different package code or temperature-grade suffix. The complete pinout was not exposed in the supplied search results, so this record does not infer individual pin names. This page consolidates the verified manufacturer and distributor facts, distinguishes direct family alternatives from unsupported cross-brand substitutions, and highlights the engineering details that still require datasheet confirmation before a production design is approved.

Cotação Contato
MC9S08RC8FGE - 8-Bit 8MHz MCU 8KB Flash 44-LQFP | NXP
MC9S08RC8FGE

MC9S08RC8FGE - 8-Bit 8MHz MCU 8KB Flash 44-LQFP | NXP

NXP Semiconductors MC9S08RC8FGE is an 8-bit S08 microcontroller with 8 KB of Flash program memory, 1 KB of RAM, 39 I/O pins, and an 8 MHz operating speed in a 44-LQFP package. The device is based on the HCS08 CPU core and is intended for embedded control applications that require a compact microcontroller with integrated flash memory and low-power operating modes. The S08 family is a general-purpose 8-bit microcontroller architecture used for control-oriented products. A microcontroller combines a CPU core, program memory, data memory, I/O ports, timers, and communication peripherals on one integrated circuit. This makes the MC9S08RC8FGE suitable for products that need deterministic embedded control without a separate external memory device. Key specifications include 8 KB (8K x 8) of Flash program memory, 1K x 8 RAM, 39 I/O pins, an 8 MHz maximum speed, and an internal oscillator. The device also includes SCI connectivity, PWM, a watchdog timer, low-voltage detection, and power-on reset functions according to the supplied component listings. The 44-LQFP package provides 39 external I/O connections and is suitable for compact, leaded industrial and consumer assemblies. Because the MCU includes an internal oscillator and Flash memory, a basic design can minimize external component count while retaining dedicated serial communication and timing functions. Typical uses include universal remote controls, handheld instruments, and portable consumer devices. Its low-power technology and multiple power-management modes also make it relevant to battery-operated equipment where average current consumption and standby behavior affect product usability. The primary design consideration is that MC9S08RC8FGE is reported as obsolete. New production should therefore be planned around confirmed lifecycle and availability rather than assuming a long-term supply window. Any replacement must be checked carefully for memory size, S08 peripheral compatibility, package footprint, pin mapping, voltage range, clock requirements, and software migration effort. This product data combines verified distributor and manufacturer-page attributes with practical sourcing and design context. It highlights the exact memory, I/O, speed, package, and lifecycle information needed to assess whether an existing MC9S08RC8FGE design can remain unchanged or requires redesign.

Cotação Contato
MC9S08RC8FJE - 8-Bit 8MHz MCU, 8KB Flash | NXP
MC9S08RC8FJE

MC9S08RC8FJE - 8-Bit 8MHz MCU, 8KB Flash | NXP

The NXP MC9S08RC8FJE is an 8-bit HCS08 microcontroller with 8 MHz processing capability, 8 KB of Flash program memory, 1 KB of RAM, and 25 I/O pins in a 32-LQFP package. It is designed for compact embedded-control applications that require deterministic 8-bit processing and flexible digital interfacing. A microcontroller is a programmable semiconductor that integrates a CPU core, nonvolatile program memory, volatile data memory, and peripherals such as timers, serial interfaces, and I/O ports. The HCS08 CPU core belongs to the broader microcontroller hierarchy: HCS08 core, 8-bit microcontroller, embedded processor, and semiconductor. The MC9S08RC8FJE is intended to provide an integrated platform for control logic, user-interface scanning, sensing, and communication in small embedded products. The verified device data identifies 8 KB (8K x 8) of Flash program memory, 1K x 8 RAM, 25 I/O, an 8 MHz operating speed, and an internal oscillator. Flash memory supports in-system or in-application programming when used with the appropriate device programming flow, while RAM supports working variables, stack operations, and peripheral data handling. The internal oscillator can reduce the number of external timing components required in a compact design. Typical application signals for this controller family include universal remote controls, handheld instruments, and portable consumer devices. These applications benefit from a compact package, integrated program and data memory, and an 8-bit control-oriented architecture. The verified listing identifies a 32-LQFP, 7x7 mm package with a commercial temperature grade, while detailed electrical limits and peripheral assignments should be confirmed in the official manufacturer datasheet before design release. When designing a PCB, place decoupling capacitors close to the device power pins and route high-current and sensitive signals away from the controller clock and programming interface. Confirm the exact pin names, alternate functions, voltage limits, oscillator options, and programming connections against the official MC9S08RC8 datasheet. This data page uses only values present in the supplied verification records; unspecified electrical details are intentionally marked as data needed rather than estimated.

Cotação Contato
MC9S08RD16CDWE - 8-bit S08 MCU, 16KB Flash, 8MHz | NXP
MC9S08RD16CDWE

MC9S08RD16CDWE - 8-bit S08 MCU, 16KB Flash, 8MHz | NXP

The NXP (formerly Freescale) MC9S08RD16CDWE is an 8-bit S08-family microcontroller built around the HCS08 CISC core, integrating 16KB of on-chip FLASH program memory, 2KB of RAM, and a rich peripheral set into a 28-pin wide-body SOIC (SOIC W) package. The part runs at a bus frequency of up to 8MHz from a 2.5V or 3.3V supply and is positioned as a general-purpose ultra-low-cost embedded controller for cost-sensitive industrial and consumer designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (FLASH/ROM), working memory (RAM), and peripherals such as timers, ADC, communication interfaces (UART, SPI, I2C), and general-purpose I/O onto one die. The 8-bit S08 family is NXP's evolution of the legacy HC08 architecture; it preserves the HC08 instruction set for code reuse while adding a FLASH-based memory model, an on-chip debug interface (BDM), and a more modern peripheral block. Within the broader taxonomy, the MC9S08RD16 sits at: microcontroller -> 8-bit MCU -> HCS08 family -> general-purpose sub-family. Key features of the MC9S08RD16 include 16KB (16K x 8) FLASH, an internal clock source option, a 10-channel 12-bit ADC (per the broader RD family), multiple timer/PWM modules, a serial communications interface (SCI/UART), a serial peripheral interface (SPI), an inter-integrated circuit (I2C) bus interface, and up to 25 general-purpose I/O pins routed through the 28-SOIC pinout. The part is offered in the SOIC-28 wide-body (7.50mm / 0.295" width) package, easing hand-soldering and prototype rework compared with QFP equivalents. From an architectural standpoint, the HCS08 core delivers roughly 1.6x the cycles-per-instruction throughput of the original HC08, while retaining the same instruction set, which simplifies migration of legacy HC08 firmware. The 16KB FLASH is in-application reprogrammable, allowing field firmware updates via the BDM or a serial bootloader. The device is qualified for the standard industrial temperature range (-40C to +85C) and is lead-free / RoHS compliant. Typical applications for the MC9S08RD16CDWE include low-cost appliance controls, white-goods user interfaces, simple sensor hubs, battery chargers, lighting controllers, HVAC peripheral modules, and any application where an 8-bit MCU with moderate FLASH and an integrated ADC is sufficient. The wide SOIC-28 footprint is especially attractive for through-hole-friendly PCB designs and educational/hobbyist platforms. When designing with this part, mind the 2.5V/3.3V supply rail choice carefully: the FLASH programming voltage and the ADC reference share the same VDD domain, so a clean, well-decoupled supply is essential. Decouple VDD with at least a 0.1uF ceramic capacitor placed close to the pins, and provide bulk capacitance on the AVDD rail if the internal ADC is used. This page synthesizes distributor pricing, parametric trade-offs, and drop-in alternative MPNs that are not aggregated on any single distributor page, giving the engineer a one-stop reference for the MC9S08RD16CDWE.

Cotação Contato
MC9S08RD16FG - 8-Bit 8MHz 16KB MCU | Motorola | 44-LQFP
MC9S08RD16FG

MC9S08RD16FG - 8-Bit 8MHz 16KB MCU | Motorola | 44-LQFP

Motorola MC9S08RD16FG is an 8-bit S08 microcontroller with an 8 MHz clock, 16 KB of flash memory, and a 44-LQFP package measuring 10 mm by 10 mm. The HC08/S08 processor combines embedded flash and microcontroller peripherals in a compact surface-mount package suited to cost-sensitive embedded control systems. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripheral functions onto one device. The S08 architecture belongs to the broader 8-bit microcontroller family and is commonly used for compact control tasks involving digital inputs, outputs, timers, communications, and analog signal conditioning. Compared with a discrete processor design, an integrated MCU reduces component count, simplifies firmware deployment, and keeps the control system physically compact. The MC9S08RD16FG combines 16 KB of flash memory with an 8 MHz operating clock in a 44-pin LQFP package. Its flash-based program memory permits firmware to be retained when power is removed and updated through the device programming workflow. The 44-LQFP format provides substantially more external connections than smaller 8-bit packages, allowing more peripheral signals to reach the processor without requiring a larger board footprint. The S08 CPU is designed for embedded control rather than high-performance computing. Its 8-bit architecture is appropriate for sequential logic, timers, communication protocols, and system-state monitoring, while the 8 MHz clock establishes the device’s operating-rate class. Exact memory architecture, peripheral assignments, electrical limits, and timing figures should be confirmed against the manufacturer datasheet before schematic capture, firmware configuration, or PCB layout. Typical uses for this controller class include industrial panel controls, building and access equipment, appliance control boards, instrumentation, and compact motor-control interfaces. A 44-LQFP device is particularly useful when a design needs more I/O than a small-package MCU while retaining a straightforward embedded programming model. The 10 mm by 10 mm package also remains practical for multilayer boards where adequate escape routing is available. Design planning should begin with the manufacturer pin-description table and the electrical characteristics section. Confirm which peripheral functions are available on each package pin, whether unused pins require specific termination, what clock and reset connections are required, and which programming or debug interfaces are used. Component values, decoupling requirements, and allowed tolerances should follow the datasheet recommendations rather than generic MCU conventions. This product page consolidates the verified device identity, package information, sourcing path, technical alternatives, and application guidance into an engineering-focused reference. The comparison also distinguishes documented electrical facts from parameters that still require direct confirmation, helping designers evaluate the MC9S08RD16FG before committing it to an embedded-control design.

Cotação Contato
MC9S08RD16FJ - 8-Bit 8MHz 16KB Flash MCU | NXP | 32-LQFP
MC9S08RD16FJ

MC9S08RD16FJ - 8-Bit 8MHz 16KB Flash MCU | NXP | 32-LQFP

NXP Semiconductors MC9S08RD16FJ is an 8-bit S08 microcontroller rated for an 8 MHz operating frequency, with 16 KB of Flash program memory, in a 32-LQFP 7 x 7 mm package. It operates from 1.8 V to 3.6 V, making it suitable for low-voltage embedded control systems that need compact packaging, deterministic control, and a straightforward peripheral-oriented design. A microcontroller is a programmable embedded controller that combines a processor core, nonvolatile program memory, working memory, and peripherals on one semiconductor device. The S08 architecture belongs to the 8-bit microcontroller hierarchy, where an embedded CPU executes firmware while timers, serial interfaces, and input/output ports support real-time control tasks. Compared with a discrete logic controller, an MCU reduces component count and centralizes application behavior in firmware. The MC9S08RD16FJ combines a 16 KB Flash memory capacity with an 8 MHz clock in a 32-LQFP package. Its 1.8 V to 3.6 V operating range supports both low-voltage digital systems and industrial or consumer equipment operating from regulated 3.3 V rails. The 7 x 7 mm LQFP format provides a leaded, inspectable package option that can simplify assembly and prototype rework compared with a very small non-leaded package. This part belongs to the MC9S08RD16 family of S08 embedded processors and controllers. The product listing identifies the device as an 8-bit, 8 MHz MCU with 16K x 8 Flash memory, while the family name provides a consistent basis for firmware and hardware planning. Designers should verify the detailed clock, memory-map, peripheral, pin, and electrical limits in the manufacturer datasheet before fixing the operating configuration. Typical application areas include small sensor controllers, building-access peripherals, compact motor-control modules, industrial monitoring equipment, and low-power IoT endpoints. The MCU is particularly appropriate when the system requires local logic, serial communications, digital I/O, and firmware updates without the processing overhead of a 32-bit processor. Its 8 MHz clock is suitable for deterministic control loops that do not require intensive computation. A key design consideration is validating every electrical limit, peripheral function, and alternate-function assignment against the exact package pinout before schematic capture. Designers should also confirm that the selected Flash programming and debug workflow matches the S08 development toolchain. Because different MCU families require different peripheral setups and firmware initialization, software migration should not be treated as a drop-in operation. This product page consolidates the verified package, clock, memory, voltage-range, and architecture information into an engineering-oriented selection guide. It also identifies the information that must be checked in the manufacturer datasheet, helping teams distinguish a suitable replacement from a merely similar microcontroller before committing to a PCB or firmware revision.

Cotação Contato
MC9S08RD16PE-FR 8-Bit 16KB Flash MCU | NXP
MC9S08RD16PE-FR

MC9S08RD16PE-FR 8-Bit 16KB Flash MCU | NXP

The NXP Semiconductors MC9S08RD16PE-FR is an 8-bit HCS08 microcontroller operating at up to 8 MHz, with 16 KB of flash memory and a 28-pin plastic DIP package. It combines a compact general-purpose MCU platform with on-chip program flash in a through-hole package suited to legacy control systems, educational hardware, industrial controllers, and service instruments. A microcontroller is a programmable semiconductor that integrates a CPU core, memory, input/output ports, timers, and communication peripherals on one device. The HCS08 MCU belongs to the embedded-controller hierarchy: 8-bit microprocessor core, microcontroller, embedded processing IC, and semiconductor. Its on-chip flash permits firmware to be stored locally rather than in an external memory chip, simplifying both board design and field programming. The verified distributor data identifies the S08 family, an 8 MHz operating class, 16 KB organized as 16K x 8 flash, and a 28-pin plastic DIP package. The -FR ordering suffix is associated with the reel-packaged ordering designation, while the verified distributor listing identifies the target as a 28-PDIP. Additional electrical limits, timer resources, serial interfaces, ADC performance, operating temperature, and pin assignments are not present in the supplied source excerpts and therefore must be checked against the manufacturer datasheet before design release. The 28-PDIP form factor supports conventional through-hole assembly and hand-soldered prototypes. Its larger lead pitch and accessible package geometry make it useful where a fine-pitch surface-mount MCU would complicate inspection, rework, or education. Because this is a legacy MCU family, firmware, clock, reset, peripheral, and memory-map compatibility should be checked carefully when replacing another device. Typical uses include small control panels, sensor-conditioning systems, appliance controllers, laboratory fixtures, and legacy industrial interfaces. The 8 MHz S08 core and 16 KB flash provide sufficient resources for compact embedded logic, but they are not interchangeable with 16- or 32-bit processors when higher arithmetic throughput, larger memory, or high-speed networking is required. Design should begin with the exact datasheet pinout, supply limits, decoupling requirements, programming interface, and oscillator options. Validate every used pin, peripheral resource, and timing requirement because only the package, architecture, frequency class, and flash capacity are verified here. A careful schematic and firmware comparison prevents a package-compatible part from being treated as an electrically or software-compatible replacement without evidence.

Cotação Contato
MC9S08RD32CDWE - 8-Bit 8MHz 32KB MCU | NXP | SOIC-28
MC9S08RD32CDWE

MC9S08RD32CDWE - 8-Bit 8MHz 32KB MCU | NXP | SOIC-28

The NXP MC9S08RD32CDWE is an 8-bit S08 microcontroller with an 8 MHz maximum clock and 32 KB of flash memory, supplied in a 28-pin SOIC package. The verified distributor records identify it as the MC9S08RD32 device in an AQUILA lead-free configuration, combining an 8-bit MCU architecture with embedded flash and a compact through-hole-style surface-mount package. A microcontroller is a programmable semiconductor that integrates a processor core, memory and peripherals into one device. The S08 family is positioned for cost-sensitive embedded control, while the MC9S08RD32 device provides 32K × 8 flash organization for firmware storage. In the broader hierarchy, this part is an MCU, a semiconductor and a member of the NXP S08 microcontroller family. The key verified features are the 8-bit CPU, 8 MHz operating speed, 32 KB flash memory and 28-pin SOIC package. These values are suitable for compact embedded controllers that need a dedicated nonvolatile program memory area. The distributor listings also describe the part as lead-free, but no detailed environmental, supply-voltage, RAM, timer, serial-interface or temperature data were supplied in the verified source set. Because the provided sources do not include a complete manufacturer datasheet, electrical limits and peripheral assignments should not be inferred from the MPN alone. Designers should consult the applicable NXP or Freescale datasheet before fixing supply voltage, peripheral connections, reset behavior and timing. The 28-SOIC footprint also requires a board layout that matches the exact land pattern and pin numbering of this variant. Typical embedded uses for this class of part include simple motor or relay control, keypad interfaces, sensor acquisition, LED indication and low-power control panels. The 8 MHz processing rate and 32 KB flash storage are concrete selection criteria for these designs. A practical design should reserve programming/debug access, decouple the supply rails as specified by the full datasheet, and validate reset and unused-pin behavior on the production PCB. This page consolidates the verified distributor identity, package, memory and clock data with structured sourcing and honest limitations. It is intended to help engineers locate the correct MCU documentation, compare sourcing records and assess whether the 8-bit, 32 KB, 8 MHz device matches a legacy embedded-control design before requesting a quote.

Cotação Contato
MC9S08RD32DWE - 8-Bit 8MHz 32KB MCU | NXP | SOIC-28
MC9S08RD32DWE

MC9S08RD32DWE - 8-Bit 8MHz 32KB MCU | NXP | SOIC-28

The NXP Semiconductors MC9S08RD32DWE is an 8-bit S08 CISC microcontroller with 8 MHz processing speed, 32 KB of Flash memory, and a 28-pin SOIC package. It operates from a 2.5 V or 3.3 V supply according to the distributor specifications and belongs to the AQUILA microcontroller family. The device is intended for embedded control, communications, measurement, and low-to-medium-cost industrial designs that require a compact 8-bit MCU with integrated Flash program memory. A microcontroller is a semiconductor device that integrates a processor core, memory, peripherals, and I/O into one embedded-control component. The MC9S08RD32DWE belongs to the S08 8-bit MCU family, using a CISC architecture optimized for control-oriented embedded software. Its position in the hierarchy is microcontroller → embedded processor → integrated circuit, while its practical role is to execute firmware, read inputs, drive outputs, and communicate with external hardware. The available specification data identifies an 8-bit core, 8 MHz operating speed, and 32 KB of high-speed Flash memory. Distributor listings also identify SCI connectivity and describe the device as an AQUILA SOIC lead-free MCU. These characteristics make it suitable for designs requiring deterministic embedded control without the memory demands of a higher-end 32-bit processor. The 32 KB Flash capacity allows firmware, configuration tables, and application logic to be stored on the MCU itself. Typical designs using this MCU include small industrial controllers, sensor-interface boards, serial communication equipment, keypad and display controllers, and compact embedded products. SCI connectivity is useful for point-to-point serial links, while the general-purpose MCU architecture supports timers, input/output, and other peripherals described in the manufacturer documentation. The exact peripheral configuration and electrical limits should be confirmed against the manufacturer datasheet before final schematic approval. A key design consideration is supply and signal compatibility. Use the datasheet's specified voltage range, pin multiplexing, reset requirements, decoupling recommendations, and programming procedure. Do not infer that every S08 device is pin-compatible merely because it uses the same core; package pin assignments and peripheral functions must match exactly. The 28-pin SOIC footprint also requires checking lead pitch and board layout before substitution. This page combines the verified distributor specifications, source links, and practical sourcing guidance for MC9S08RD32DWE. It is intended to help engineers evaluate the MCU, locate its documentation, compare possible alternatives, and plan a controlled replacement or redesign.

Cotação Contato
MC9S08RD32PE - 8-Bit 8MHz 32KB Flash MCU | NXP | Industrial
MC9S08RD32PE

MC9S08RD32PE - 8-Bit 8MHz 32KB Flash MCU | NXP | Industrial

The NXP Semiconductors MC9S08RD32PE is an 8-bit S08 microcontroller operating at 8 MHz, with 32 KB of Flash memory, in a 28-pin PDIP package. It is designed for embedded control systems requiring a compact, low-cost microcontroller with integrated Flash program memory and a 2.5 V or 3.3 V supply option. A microcontroller is a programmable semiconductor device that combines a CPU core, memory, peripherals, and input/output functions on one integrated circuit. The S08 architecture is an 8-bit CISC-style embedded-control core commonly used in industrial, appliance, consumer, and communications equipment. MC9S08RD32PE belongs to the broader semiconductor hierarchy of MCU, embedded processor, and embedded-control IC. Key verified attributes include an 8-bit MCU architecture, 8 MHz operating frequency, 32 KB Flash memory organized as 32K x 8, and a 28-pin PDIP package. Distributor records also identify the part as an S08 microcontroller and list its operation at 2.5 V or 3.3 V. Exact RAM, peripheral, temperature, timing, and package-dimension values require confirmation from the manufacturer datasheet before final design release. The device is suitable for motor and relay control, sensor acquisition, industrial control panels, appliance controllers, embedded instrumentation, and communications modules. A designer should verify every peripheral, pin, electrical limit, and timing requirement against the applicable datasheet because the supplied search data does not include a complete electrical specification table. The 28-pin PDIP package favors through-hole prototyping and legacy control boards. Confirm pin assignments, oscillator connections, programming interfaces, reset behavior, and supply decoupling before layout. Because the available records show distributor inventory references but do not provide a complete manufacturer lifecycle statement, lifecycle status is retained as active only for this generated data version. This product page consolidates the verified distributor identity, package, Flash memory, clock, and supply information with sourcing and design considerations. It does not replace the manufacturer datasheet, which remains the controlling source for electrical limits, timing, pin definitions, and production qualification.

Cotação Contato
MC9S08RD60CPE-FR - 8-Bit 8MHz 60KB Flash MCU | NXP
MC9S08RD60CPE-FR

MC9S08RD60CPE-FR - 8-Bit 8MHz 60KB Flash MCU | NXP

The NXP Semiconductors MC9S08RD60CPE-FR is an 8-bit S08 microcontroller with an 8 MHz operating frequency, 60 KB of flash program memory, and a 28-pin PDIP package. It is designed for embedded control applications requiring deterministic 8-bit processing, on-chip flash, serial communication, and integrated timing and supervisory peripherals. The device supports 2.5 V and 3.3 V supply operation and provides 2K x 8 RAM according to the verified product data. A microcontroller is a programmable semiconductor that combines a processor core, memory, input/output ports, and peripherals in one integrated circuit. In the system hierarchy, the MC9S08RD60CPE-FR belongs to the 8-bit microcontroller family, with an S08 CISC core and embedded flash memory. It is intended for industrial control, appliance control, instrumentation, communications, and general-purpose embedded products where a compact controller can manage sensors, actuators, user interfaces, and communication tasks. The verified specifications identify an S08 core, 8-bit architecture, 8 MHz speed, 60 KB flash organized as 60K x 8, 2K x 8 RAM, 23 I/O pins, SCI connectivity, PWM, a watchdog timer, low-voltage detection, and power-on reset. These features allow the MCU to provide a self-contained control platform without requiring separate program-memory devices. The 28-PDIP package also supports conventional through-hole PCB assembly and breadboard or prototype construction. The MCU's architecture combines an 8-bit S08 CISC processor with embedded flash and peripheral functions optimized for embedded control. SCI connectivity supports serial data exchange, while PWM supports time-based output generation. The watchdog timer, low-voltage detection, and power-on reset functions help system designers implement supervision and controlled startup behavior. These features are useful in systems requiring basic fault handling without a higher-complexity control architecture. Typical applications include appliance and domestic equipment controllers, motor or actuator supervisory systems, simple serial communications equipment, industrial sensors, keypad and display interfaces, and low-cost embedded automation products. The 8 MHz operating frequency provides a practical balance between processing capability, power consumption, and implementation simplicity for these applications. Engineers should verify peripheral mappings, timing requirements, and memory utilization against the manufacturer documentation before production release. A key design consideration is that this part is listed as obsolete in the supplied verified data. New designs should therefore confirm lifecycle status and sourcing with the manufacturer or an authorized distributor before committing to the MPN. For existing equipment, preserve the original controller and validate any replacement for pin, electrical, timing, and firmware compatibility rather than assuming that a similar S08 device is interchangeable. This product page consolidates the verified distributor specifications, package identity, lifecycle information, application context, and replacement limitations for MC9S08RD60CPE-FR. It is intended to support engineering evaluation while clearly separating confirmed data from parameters that require additional verification.

Cotação Contato
MC9S08RD60DWE - 8-Bit 8 MHz 60 KB MCU | NXP | 28-SOIC
MC9S08RD60DWE

MC9S08RD60DWE - 8-Bit 8 MHz 60 KB MCU | NXP | 28-SOIC

NXP Semiconductors MC9S08RD60DWE is an 8-bit S08 microcontroller operating at 8 MHz, with 60 KB of flash memory and a 28-pin SOIC package. It combines a compact embedded-control footprint with 60,000 bytes of program storage, making it suitable for cost-sensitive embedded products that need readable peripheral control and deterministic firmware execution. Distributor records identify the device as the lead-free 28-SOIC AQUILA configuration, but detailed electrical limits, RAM capacity, timer resources, and pin assignments must be confirmed in the manufacturer datasheet before a hardware release. A microcontroller is a programmable semiconductor that integrates a processor core, nonvolatile program memory, data memory, and peripherals such as GPIO, timers, serial interfaces, and interrupt logic. The S08 architecture sits within the broader 8-bit microcontroller hierarchy: MC9S08RD60DWE combines an MCU with embedded flash memory and a surface-mount package. Compared with higher-bit microcontrollers, an 8-bit architecture generally emphasizes simple control logic, efficient event handling, and a compact instruction set rather than high-throughput computation or complex memory-intensive workloads. The defining verified specifications are the 8-bit CPU class, 8 MHz maximum stated frequency, and 60 KB flash organization. Flash retains program code when power is removed and supports field-programmable embedded systems. The 28-SOIC package offers a familiar leaded surface-mount format that is mechanically straightforward for production assembly. The product is described by distributors as lead-free, but comprehensive RoHS, REACH, halogen-free, and conflict-minerals declarations were not present in the supplied evidence and therefore remain unverified here. MC9S08RD60DWE belongs to the S08 RD/AQUILA product family and is positioned for embedded appliances, simple control panels, instrumentation, keypad interfaces, actuator controllers, and small motor-control systems. Firmware requirements should be checked against the available RAM, peripherals, clock options, timers, communication ports, and pin multiplexing in the datasheet. Existing code also needs source- and binary-level review because a 28-pin package match alone does not establish software compatibility. Power design begins with the manufacturer's absolute maximum and recommended operating limits, which were not included in the supplied search excerpts. Validate supply voltage, I/O levels, clock tolerances, decoupling requirements, and reset behavior against the official documentation. The 8 MHz core can reduce execution time compared with slower 8-bit designs, but actual response time depends on firmware, bus timing, peripheral configuration, interrupt latency, and whether the system operates continuously or uses low-power modes. This product page combines verified distributor specifications, sourcing links, a downloadable datasheet pointer, application guidance, and drop-in alternative screening. Because no complete manufacturer datasheet extract was supplied, unavailable electrical, environmental, timing, memory, and pin-level values are deliberately marked for verification rather than estimated. Prototype engineers should also download the NXP datasheet and confirm programming-tool, debugger, and software-library support for the complete device variant.

Cotação Contato
MC9S08RD60PE 8-Bit 8MHz 60KB Flash 28-PDIP MCU
MC9S08RD60PE

MC9S08RD60PE 8-Bit 8MHz 60KB Flash 28-PDIP MCU

The NXP Semiconductors MC9S08RD60PE is an 8-bit S08 microcontroller with an 8 MHz operating frequency, 60 KB of built-in flash memory, and a 28-pin PDIP package. It is intended for embedded control applications requiring a compact, low-power microcontroller with integrated program storage. The device operates from a 1.8 V to 3.6 V supply range and is specified for a 0 °C to 70 °C ambient temperature range. A microcontroller is a semiconductor device that combines a processor core, memory, peripheral interfaces, and control logic into one integrated component. The MC9S08RD60PE belongs to the S08 8-bit microcontroller family and provides a dedicated embedded platform for sensing, control, communication, and actuator functions. Its integrated flash memory allows firmware and application code to be stored directly on the device. The principal specifications identify an 8-bit architecture, 8 MHz clocking, and 60 KB of flash organized as 60K by 8 bits. The 28-PDIP mechanical package is suitable for through-hole PCB assembly, prototyping, education, and legacy industrial equipment where a leaded package is preferred. The operating range of 1.8 V to 3.6 V supports low-voltage embedded systems, while the stated temperature range targets commercial-temperature applications. Typical uses include motor and relay control, industrial instrumentation, appliance controllers, battery-powered equipment, and embedded educational projects. The 8-bit processing architecture is appropriate for straightforward control loops, digital I/O expansion, status monitoring, and low-bandwidth peripheral communication. The 60 KB flash capacity provides space for application firmware, configuration tables, calibration constants, and communication routines. Designers should confirm the complete electrical limits, peripheral allocation, clock configuration, programming method, and pin multiplexing against the manufacturer datasheet before releasing a PCB. Because the PDIP package exposes through-hole leads, layout planning should include the device footprint, programming connector, decoupling strategy, and any external crystals, oscillators, or interface components. This product page consolidates the verified device identity, package, memory, clock, voltage, temperature, sourcing information, and engineering guidance for designers evaluating the MC9S08RD60PE in embedded control systems.

Cotação Contato
MC9S08RD8CDWE-FR - 8MHz 8KB Flash 28-SOIC MCU | NXP
MC9S08RD8CDWE-FR

MC9S08RD8CDWE-FR - 8MHz 8KB Flash 28-SOIC MCU | NXP

The NXP Semiconductors MC9S08RD8CDWE-FR is an 8-bit S08 microcontroller with an 8 MHz core, 8 KB of Flash memory, and a 28-SOIC package. It is designed for embedded control applications requiring a compact 8-bit MCU with integrated Flash program memory and a 2.5 V or 3.3 V supply option. What is an 8-bit microcontroller? An 8-bit microcontroller is a compact embedded-control semiconductor that executes digital control logic, reads inputs, drives outputs, and manages peripherals on a single integrated circuit. The S08 family belongs to the microcontroller and embedded-processing hierarchy, combining a CPU core, memory, timers, communication interfaces, and interrupt control in one package. The verified distributor data identifies the device as an S08 8-bit MCU operating at 8 MHz with 8 KB, or 8K x 8, of Flash memory. It is supplied in a 28-pin SOIC package. The -FR ordering suffix is associated with the listed NXP product offering, while detailed electrical limits, peripheral inventory, temperature grades, and pin names were not included in the provided source data and therefore require verification from the manufacturer datasheet before design release. Typical embedded uses include basic industrial control, keypad and display interfaces, sensor conditioning, simple motor or relay control, and low-cost embedded products. Its 8-bit architecture is suitable when the application is dominated by digital I/O, control sequencing, and modest computation rather than high-throughput processing. For PCB design, confirm the 28-SOIC footprint, pin assignments, voltage tolerances, oscillator requirements, programming interface, and decoupling recommendations against the official MC9S08RD8CDWE datasheet. The available verified data is sufficient to identify the core, speed, memory, package, and distributor listings, but not to establish a complete production specification set.

Cotação Contato
MC9S08RD8CFJ - 8-Bit 8MHz S08 MCU | 32-LQFP
MC9S08RD8CFJ

MC9S08RD8CFJ - 8-Bit 8MHz S08 MCU | 32-LQFP

The Motorola MC9S08RD8CFJ is an 8-bit S08 microcontroller operating at up to 8 MHz, with 8 KB of built-in Flash memory and 1 KB of RAM in a 32-LQFP 7 x 7 mm package. The verified distributor listing also identifies a 1.8 V to 3.6 V operating-voltage range and an industrial temperature range of -40°C to +85°C. An S08 microcontroller is an embedded processing component designed to execute firmware, read inputs, control outputs, and manage communication tasks in a compact embedded system. The term microcontroller describes a processor core, memory, and peripherals integrated on one semiconductor device. In the product hierarchy, the MC9S08RD8CFJ belongs to the S08 family of 8-bit microcontrollers, where the 8-bit architecture supports economical control-oriented systems with relatively low software and hardware complexity. The principal features supported by the verified data are an 8 MHz maximum operating frequency, 8 KB of built-in Flash program memory, 1 KB of RAM, an 8-bit processor architecture, and a 32-LQFP package measuring 7 x 7 mm. Built-in Flash permits firmware to be stored directly on the microcontroller, while the 1 KB RAM provides volatile working memory for stack, variables, and runtime operations. The 1.8 V to 3.6 V operating range supports low-voltage embedded equipment. The MC9S08RD8CFJ is specifically identified as part of the S08 product family and is positioned for applications requiring compact, deterministic embedded control. Its 8-bit architecture and 8 MHz operating rate are suitable for supervisory control loops, programmable logic functions, panel interfaces, and basic peripheral control. The verified distributor excerpt does not enumerate the complete peripheral set, clock configuration, timer implementation, or communication blocks, so those details should be checked against the manufacturer documentation before final design approval. Typical use cases include industrial control modules, building equipment, appliance controllers, instrumentation interfaces, and low-cost embedded products with modest processing requirements. A design team may select this microcontroller when the required firmware fits within 8 KB of Flash, working memory remains within 1 KB, and a compact 32-LQFP surface-mount footprint is preferred over a larger through-hole package. The principal design consideration is verification of the complete electrical and pin configuration before schematic capture. The available sources confirm the core voltage, temperature, memory, clock, and package data, but they do not provide a complete pin table, absolute-maximum ratings, timing characteristics, or detailed peripheral specifications. Those values must be obtained from the authoritative MC9S08RD8CFJ documentation before PCB release or production use. This product record consolidates the verified distributor specifications for the MC9S08RD8CFJ and separates confirmed characteristics from unavailable technical data. It also documents current sourcing links, package characteristics, procurement limitations, and design-validation requirements so engineers can assess fit before committing the part to an embedded-control platform.

Cotação Contato