5M160ZE64C5 - MAX V CPLD, 160 LEs, 64-EQFP | Intel (Altera)
N.º da peça: 5M160ZE64C5 ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $7.45 | $7,45 |
| 10 | $6.78 | $67,80 |
| 100 | $6.05 | $605,00 |
| 500 | $5.42 | $2.710,00 |
| 1.000 | $4.85 | $4.850,00 |
5M160ZE64C5 Visão geral
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that sits in the broader programmable logic hierarchy between simple PLDs (SPLDs) and FPGAs. CPLDs use a deterministic interconnect fabric and Flash-based configuration memory to provide instant-on behavior at power-up, making them ideal for glue logic, bus interfacing, power-up sequencing, and state-machine control. The MAX V family specifically targets low-cost, low-power applications by integrating a Flash memory block and eliminating external configuration devices.
Key features of the 5M160ZE64C5 include 7.5 ns pin-to-pin logic delay (tPD), 118.3 MHz maximum internal frequency, 1.8 V core voltage (Z designation), 3.3 V or 2.5 V multi-voltage I/O support, in-system programmability (ISP) via JTAG, and 128 Kbits of user Flash memory (UFM) usable as general-purpose non-volatile storage. The device uses a 4-input look-up table (LUT) architecture with a global routing pool and supports IEEE 1149.1 boundary-scan testing.
The 5M160ZE64C5 uses a non-volatile Flash configuration cell based on a 0.18 micrometer process, providing instant-on operation and unlimited reconfigurability without external boot memory. Its MultiVolt I/O banks allow mixed-voltage interfacing on the same die, simplifying PCB designs that need to bridge 3.3 V peripherals with 2.5 V or 1.8 V processors, while the built-in JTAG port enables in-circuit reconfiguration during prototyping and field upgrades.
Typical applications include industrial control and glue logic, I/O expansion and bus bridging, power-up sequencing and supervisory logic, LED display drivers, and consumer electronics interface controllers. The instant-on Flash-based architecture is particularly useful in safety-critical or deterministic-latency paths where FPGAs would require boot time.
When designing with this device, note the difference between commercial-grade (C5 suffix) and industrial-grade (I5 suffix) temperature ranges. Ensure JTAG chain integrity by buffering TMS/TCK signals when multiple devices share the chain, and respect the 1.8 V core supply ramp time recommended in the datasheet to avoid configuration corruption.
This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found on a single manufacturer datasheet view, including cross-brand Intel/Altera MAX V family cross-references and direct EQFP-64 pinout data for engineers evaluating the 5M160ZE64C5 against other 160-LE CPLDs.
Alternativas drop-in para 5M160ZE64C5 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com 5M160ZE64C5 (mesmo formato e footprint) — diferindo em Package, Operating Temperature, Programming Interface, Mounting Type, Device Family.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
5M160ZE64C5N
✅ Drop-In✓ Em estoque
$4.95 / unidade
Ver ficha técnica →5M160ZE64C4N
✅ Drop-In✓ Em estoque
$4.3 / unidade
Ver ficha técnica →5M160ZE64A5N
✅ Drop-In✓ Em estoque
$6.2 / unidade
Ver ficha técnica →5M160ZE64I5N
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$4.13 / unidade
Ver ficha técnica →5M160ZE64I5
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$4.1 / unidade
Ver ficha técnica →5M160ZE64C5 Classificações máximas e características elétricas
| Device Family | MAX V |
| Logic Elements (LEs) | 160 |
| Macrocells | 128 |
| User I/Os | 54 |
| Internal Frequency (max) | 184 MHz |
| Propagation Delay (tPD) | 7.9 ns |
| Pin-to-Pin Logic Delay | 7.5 ns |
| User Flash Memory (UFM) | 8 Kbits |
| Core Voltage | 1.8 V (Z) |
| I/O Standards Supported | LVCMOS 3.3 V / 2.5 V / 1.8 V, LVTTL |
| Encapsulamento | EQFP-64 (Plastic, 9x9 mm, 0.4 mm pitch) |
| Operating Temperature Grade | Commercial (0C to +85C) |
| Speed Grade | 5 (fastest) |
| Programming Interface | JTAG (IEEE 1149.1) ISP |
| Tipo de montagem | Surface Mount |
| Status RoHS | Compliant |
| Configuration Memory Type | Flash (non-volatile, instant-on) |
Configuração de pinos do 5M160ZE64C5
| Pino 1 | I/O — General-purpose user I/O (Bank 1) |
| Pino 2 | I/O — General-purpose user I/O (Bank 1) |
| Pino 3 | I/O — General-purpose user I/O (Bank 1) |
| Pino 4 | I/O — General-purpose user I/O (Bank 1) |
| Pino 5 | I/O — General-purpose user I/O (Bank 1) |
| Pino 6 | I/O — General-purpose user I/O (Bank 1) |
| Pino 7 | VCCIO1 — I/O Bank 1 supply voltage (3.3 V / 2.5 V / 1.8 V) |
| Pino 8 | I/O — General-purpose user I/O (Bank 1) |
| Pino 9 | I/O — General-purpose user I/O (Bank 1) |
| Pino 10 | GND — Ground |
| Pino 11 | I/O — General-purpose user I/O (Bank 2) |
| Pino 12 | I/O — General-purpose user I/O (Bank 2) |
| Pino 13 | I/O — General-purpose user I/O (Bank 2) |
| Pino 14 | I/O — General-purpose user I/O (Bank 2) |
| Pino 15 | I/O — General-purpose user I/O (Bank 2) |
| Pino 16 | I/O — General-purpose user I/O (Bank 2) |
| Pino 17 | VCCIO2 — I/O Bank 2 supply voltage (3.3 V / 2.5 V / 1.8 V) |
| Pino 18 | I/O — General-purpose user I/O (Bank 2) |
| Pino 19 | I/O — General-purpose user I/O (Bank 2) |
| Pino 20 | GND — Ground |
| Pino 21 | I/O — General-purpose user I/O (Bank 3) |
| Pino 22 | I/O — General-purpose user I/O (Bank 3) |
| Pino 23 | I/O — General-purpose user I/O (Bank 3) |
| Pino 24 | I/O — General-purpose user I/O (Bank 3) |
| Pino 25 | I/O — General-purpose user I/O (Bank 3) |
| Pino 26 | I/O — General-purpose user I/O (Bank 3) |
| Pino 27 | VCCIO3 — I/O Bank 3 supply voltage (3.3 V / 2.5 V / 1.8 V) |
| Pino 28 | I/O — General-purpose user I/O (Bank 3) |
| Pino 29 | I/O — General-purpose user I/O (Bank 3) |
| Pino 30 | GND — Ground |
| Pino 31 | I/O — General-purpose user I/O (Bank 4) |
| Pino 32 | I/O — General-purpose user I/O (Bank 4) |
| Pino 33 | I/O — General-purpose user I/O (Bank 4) |
| Pino 34 | I/O — General-purpose user I/O (Bank 4) |
| Pino 35 | I/O — General-purpose user I/O (Bank 4) |
| Pino 36 | I/O — General-purpose user I/O (Bank 4) |
| Pino 37 | VCCIO4 — I/O Bank 4 supply voltage (3.3 V / 2.5 V / 1.8 V) |
| Pino 38 | I/O — General-purpose user I/O (Bank 4) |
| Pino 39 | I/O — General-purpose user I/O (Bank 4) |
| Pino 40 | GND — Ground |
| Pino 41 | I/O — General-purpose user I/O (Bank 4) |
| Pino 42 | I/O — General-purpose user I/O (Bank 4) |
| Pino 43 | TDI — JTAG Test Data In |
| Pino 44 | TMS — JTAG Test Mode Select |
| Pino 45 | TCK — JTAG Test Clock |
| Pino 46 | TDO — JTAG Test Data Out |
| Pino 47 | VCCINT — Core supply voltage (1.8 V) |
| Pino 48 | GND — Ground |
| Pino 49 | I/O — General-purpose user I/O (Bank 1) |
| Pino 50 | I/O — General-purpose user I/O (Bank 1) |
| Pino 51 | I/O — General-purpose user I/O (Bank 1) |
| Pino 52 | I/O — General-purpose user I/O (Bank 1) |
| Pino 53 | I/O — General-purpose user I/O (Bank 1) |
| Pino 54 | I/O — General-purpose user I/O (Bank 1) |
| Pino 55 | I/O — General-purpose user I/O (Bank 1) |
| Pino 56 | I/O — General-purpose user I/O (Bank 1) |
| Pino 57 | I/O — General-purpose user I/O (Bank 1) |
| Pino 58 | I/O — General-purpose user I/O (Bank 1) |
| Pino 59 | VCCINT — Core supply voltage (1.8 V) |
| Pino 60 | GND — Ground |
| Pino 61 | I/O — General-purpose user I/O (Bank 1) |
| Pino 62 | I/O — General-purpose user I/O (Bank 1) |
| Pino 63 | I/O — General-purpose user I/O (Bank 1) |
| Pino 64 | I/O — General-purpose user I/O (Bank 1) |
Aplicações típicas
5M160ZE64C5 é adequado para 7 aplicaçãos: Industrial Glue Logic and Bus Bridging, Power-Up Sequencing and Supervisory Logic, I/O Expansion and GPIO Extenders, LED Display and Signage Drivers, Consumer Electronics Interface Controllers, Motor Control and PWM Generation, Legacy Logic Replacement and Board Modernization.
Industrial Glue Logic and Bus Bridging
The 5M160ZE64C5 excels at industrial glue logic with 160 LEs and 54 user I/Os in a compact 64-pin EQFP package. Its instant-on Flash configuration eliminates FPGA boot delays, making it ideal for address decoding, interrupt prioritization, and bus protocol translation between asynchronous logic domains. The 7.5 ns tPD and 184 MHz fMAX handle typical 50-100 MHz industrial bus speeds (SPI, I2C, UART) with margin. MultiVolt I/O banks allow direct 3.3 V-to-2.5 V bridging without level shifters. JTAG ISP enables field upgrades of glue logic without desoldering. Engineers use it to consolidate discrete 74-series logic into one programmable device, reducing PCB area up to 60 percent while adding reconfigurability.
Recomendado
Power-Up Sequencing and Supervisory Logic
The 5M160ZE64C5's deterministic instant-on behavior makes it ideal for power-up sequencing in multi-rail systems. With 160 LEs it can implement state-machine-based rail enabling, fault detection, and reset distribution for 4-8 power domains. The 7.9 ns propagation delay ensures precise timing margins between rail assertions. Its non-volatile Flash configuration means sequencing logic is active within microseconds of VCCINT ramp, before any FPGA or processor boots. Industrial temperature parts (5M160ZE64I5N) extend sequencing reliability into harsh environments. The UFM block stores factory calibration and sequencing parameters that persist across power cycles.
Recomendado
I/O Expansion and GPIO Extenders
The 5M160ZE64C5 with 54 user I/Os is well-suited as an I/O expander for processors that lack sufficient GPIOs. Engineers commonly configure it as an I2C-to-GPIO bridge, providing up to 54 additional general-purpose pins controlled by a 2-wire interface. The MultiVolt I/O banks allow the CPLD side to operate at 3.3 V or 2.5 V while the processor remains at 1.8 V. Each I/O supports programmable pull-ups, slew-rate control, and bus-hold, eliminating external resistors. The instant-on Flash memory means the I/O expansion is ready before main processor boot, allowing early board-level diagnostics and LED indicators.
Recomendado
LED Display and Signage Drivers
The 5M160ZE64C5's 54 I/Os and 184 MHz performance suit LED matrix driving, signage refresh, and visual indicator applications. With 160 LEs it can implement PWM dimming for 8-16 channels, scanning logic for multiplexed LED arrays, and serial-to-parallel conversion for LED driver chains. The 7.5 ns tPD supports high-refresh-rate video walls and persistence-of-vision (POV) displays. Commercial temperature grade is sufficient for indoor signage; industrial grade parts handle outdoor enclosures. The UFM stores display patterns and animation sequences that survive power cycles, useful for self-running display signs.
Recomendado
Consumer Electronics Interface Controllers
The 5M160ZE64C5 serves as a low-cost interface controller in consumer electronics, handling button matrix scanning, IR remote decoding, rotary encoder processing, and simple user-interface state machines. The 160-LE capacity supports 4x4 to 8x8 button matrices with debouncing logic. Its 1.8 V core and MultiVolt I/Os interface directly to low-power microcontrollers. Commercial temperature and low unit cost (around $5 at qty 1000) make it economical for high-volume consumer products. JTAG ISP allows post-assembly firmware updates via standard programming tools.
Recomendado
Motor Control and PWM Generation
The 5M160ZE64C5 generates multi-channel PWM waveforms for small motor drives, fans, and solenoid control. With 160 LEs it can implement 6-12 independent PWM channels with programmable dead-time, fault inputs, and complementary outputs. The 184 MHz fMAX supports PWM frequencies up to several hundred kHz with fine duty-cycle resolution. Instant-on Flash memory means motor control is operational within microseconds of power-up, before any MCU firmware loads. JTAG boundary-scan and ISP support simplify manufacturing test and field upgrades. MultiVolt I/O banks allow direct interfacing with 3.3 V gate drivers or 5 V through level shifters.
Recomendado
Legacy Logic Replacement and Board Modernization
The 5M160ZE64C5 is widely used to replace legacy discrete TTL/CMOS 74-series logic on aging boards. A single 160-LE CPLD can replace 5-20 discrete logic packages, reducing PCB area, BOM count, and power consumption. Designers port their existing schematic logic to HDL (Verilog or VHDL) and synthesize into the MAX V device. The instant-on Flash memory makes the replacement transparent to existing software. JTAG boundary-scan provides testability that discrete logic lacks. This is a common modernization path for industrial controllers, test equipment, and instrumentation originally built in the 1990s-2000s.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para 5M160ZE64C5 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | 5M160ZE64C5N | 5M160ZE64C4N | 5M160ZE64A5N | 5M160ZE64I5N | 5M160ZE64I5 |
|---|---|---|---|---|---|---|
| Package | EQFP-64 | EQFP-64 - same | EQFP-64 - same | EQFP-64 - same | EQFP-64 - same | EQFP-64 - same |
| Brand | Intel (Altera) | Intel (Altera) | Intel (Altera) | Intel (Altera) | Intel (Altera) | Intel (Altera) |
| Logic Elements (LEs) | 160 | 160 | 160 | 160 | 160 | 160 |
| User I/Os | 54 | 54 | 54 | 54 | 54 | 54 |
| Speed Grade | 5 (fastest) | 5 | 4 | A (slowest) | 5 | 5 |
| Temperature Grade | Commercial (0C to +85C) | Commercial | Commercial | Industrial / Commercial | Industrial (-40C to +100C) | Industrial (-40C to +100C) |
| Pb-Free Finish (N suffix) | No (SnPb) | Yes | Yes | Yes | Yes | No (SnPb) |
| Internal Frequency (max) | 184 MHz | 184 MHz | Lower (grade 4) | Lower (grade A) | 184 MHz | 184 MHz |
Principais diferenciais
- Fastest speed grade in MAX V 160-LE family (vs 5M160ZE64C4N (speed grade 4))
- Commercial temperature grade at lowest cost (vs 5M160ZE64I5N (industrial grade))
- SnPb lead finish for non-Pb-free reflow compatibility (vs 5M160ZE64C5N (Pb-free N variant))
Notas de projeto
The 5M160ZE64C5 requires a clean 1.8 V VCCINT supply with monotonic ramp from 0 V to 1.8 V in less than 100 ms per datasheet. Brown-out or slow ramp can corrupt Flash configuration. Place a 100 nF decoupling capacitor within 5 mm of each VCCINT pin and a 10 uF bulk capacitor near the PCB supply entry. VCCIO banks (VCCIO1 through VCCIO4) must each have their own 100 nF decoupling capacitor. Do not power VCCINT before VCCIO is stable - sequence supplies in any order but ensure both reach regulation within datasheet limits. Estimated: Icore ~20-50 mA typical, I/O current up to ~25 mA per bank depending on switching activity.
The 64-pin EQFP package has 0.4 mm pitch leads, requiring fine-pitch PCB layout. Use 0.2 mm trace width with 0.2 mm spacing to route signals between pads. Add a continuous ground plane on the layer directly beneath the device for thermal dissipation and signal integrity. Thermal resistance theta_JA is approximately 35 C/W for the EQFP-64 package; ensure adequate copper pour (at least 1 sq inch connected to GND) to keep junction temperature below 125 C under worst-case industrial operation. Place JTAG pins (TMS/TCK/TDI/TDO) on accessible test points or a header for in-system programming during prototyping.
Common pitfalls with the 5M160ZE64C5 include: (1) forgetting that the device is 5 V-tolerant only on JTAG pins, not on general I/O - do not apply 5 V to user I/Os; (2) confusing the 5M160Z (1.8 V core) with the older 5M160 (5 V core) MAX V devices - they are NOT pin-compatible at 1.8 V vs 5 V VCCINT; (3) leaving unused I/O pins floating - configure them as outputs driving low or as inputs with internal weak pull-up enabled to prevent noise coupling; (4) exceeding the 16 mA DC sink/source current per I/O pin; (5) not providing the recommended JTAG pull-up on TMS and TDI - floating JTAG inputs can cause configuration failures. Refer to MAX V device datasheet for absolute maximum ratings and recommended operating conditions.
Informações de conformidade
5M160ZE64C5 (non-N suffix) uses SnPb lead finish - select 5M160ZE64C5N for Pb-free compliance. MAX V family is not AEC-Q100 qualified - choose MAX 10 or Cyclone IV for automotive.
