5M160ZT100C4N - MAX V CPLD, 160 LE, 100-TQFP | Intel
N.º da peça: 5M160ZT100C4N ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $8.85 | $8,85 |
| 10 | $7.97 | $79,70 |
| 100 | $6.5 | $650,00 |
| 500 | $5.62 | $2.810,00 |
| 1.000 | $4.95 | $4.950,00 |
5M160ZT100C4N Visão geral
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that sits between simple PLDs (PAL/GAL) and high-density FPGAs in the programmable logic hierarchy. CPLDs combine a sea of AND/OR logic with a fixed interconnect fabric and non-volatile configuration, providing deterministic timing, fast I/O response, and instant-on behavior. Within the broader taxonomy: CPLD -> Programmable Logic -> Logic IC -> Integrated Circuit -> Semiconductor. MAX V devices are commonly used for I/O expansion, bus bridging, glue logic, and power sequencing in systems that need deterministic latency below 5 ns without the cost, power, or configuration overhead of an FPGA.
Key features of the 5M160ZT100C4N include 160 LEs split across two logic array blocks (LABs), up to 8 Kbits of user flash memory (UFM) for parameter storage, JTAG (IEEE 1149.1) and ISP (in-system programmability) via the JTAG pins (TDI/TDO/TMS/TCK), and built-in support for LVCMOS, LVTTL, PCI, and SSTL I/O standards. The internal 8 Kbit UFM block can be split between logic and user data, making the device suitable for storing revision IDs, calibration constants, or serial numbers without an external EEPROM.
Architecturally, the 5M160ZT100C4N uses a non-volatile flash-based configuration cell backed by a CMOS logic fabric. Every LE connects through a fast, predictable interconnect that delivers the same 7.9 ns delay regardless of routing path - a property that simplifies static timing analysis. The multi-voltage I/O banks each support an independent VCCIO rail (1.2 V to 3.3 V) on Bank 1, with Bank 2 through Bank 4 powered by the same VCCIO pin group. The 100-pin TQFP package provides ample I/O for medium-complexity glue-logic designs while remaining hand-solderable for prototypes.
Typical applications include I/O expansion and bus bridging in industrial controllers, power-supply sequencing in ATCA and telecom systems, address decoding for memory and peripheral interfaces, board-level glue logic between microcontrollers and ASICs/ASSPs, and instant-on control logic in motor drives. The device is also used in display interface bridging, legacy interface emulation, and consumer audio/video product glue.
When designing with the 5M160ZT100C4N, ensure that the JTAG chain (TCK, TMS, TDI, TDO) is accessible for in-system programming and boundary-scan test. The UFM block, if used, requires careful planning to avoid contention with logic-array usage. For thermal management, the 100-pin TQFP has a theta_JA of approximately 35 C/W, sufficient for most commercial designs without an explicit heatsink.
This page synthesizes distributor pricing, drop-in alternatives drawn from the same MAX V family, and practical design notes not found in the manufacturer datasheet alone.
Alternativas drop-in para 5M160ZT100C4N — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com 5M160ZT100C4N (mesmo formato e footprint) — diferindo em Package, Operating Temperature, Programming Interface, I/O Voltage (VCCIO), Configuration Memory.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
5M160ZT100C5N
✅ Drop-In✓ Em estoque
$4.75 / unidade
Ver ficha técnica →5M160ZT100A5N
✅ Drop-In✓ Em estoque
$4.9 / unidade
Ver ficha técnica →5M160ZT100I5N
✅ Drop-In✓ Em estoque
$4.1 / unidade
Ver ficha técnica →5M1270ZT144C4N
✅ Drop-In✓ Em estoque
$9.49 / unidade
Ver ficha técnica →5M160ZM100C4N
✅ Drop-In✓ Em estoque
$1.4 / unidade
Ver ficha técnica →5M160ZT100C4N Classificações máximas e características elétricas
| Family | MAX V |
| Logic Elements (LEs) | 160 |
| Macrocells | 128 |
| User I/Os | 79 |
| User Flash Memory (UFM) | 8 Kbits |
| Pin-to-Pin Logic Delay (tPD) | 7.9 ns |
| Core Supply Voltage (VCCINT) | 1.8 V |
| I/O Bank Supply (VCCIO) | 1.2 V to 3.3 V |
| Configuration Memory | Non-volatile flash |
| Programmability | In-system via JTAG (IEEE 1149.1) |
| Encapsulamento | TQFP-100 (100-pin) |
| Tipo de montagem | Surface Mount |
| Operating Temperature Grade | Commercial (0 C to +85 C) |
| Nível MSL | 3 |
| Status RoHS | Compliant |
| Lead-Free | Yes |
| Logic Array Blocks (LABs) | 2 |
Guia de Configuração de Pinos do 5M160ZT100C4N tqfp-100 (100-pin)
Configuração de pinos para 5M160ZT100C4N (pacote tqfp-100 (100-pin)). Este CI digital inclui GPIO, interfaces de comunicação (UART, SPI, I2C) e pinos de alimentação. Consulte o datasheet do fabricante para funções alternativas dos pinos e opções de configuração. Essencial para projeto de sistemas embarcados e layout de PCB.
Nenhum dado detalhado de pinagem disponível para 5M160ZT100C4N.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
5M160ZT100C4N é adequado para 7 aplicaçãos: I/O Expansion for Microcontrollers, Bus Bridging and Address Decoding, Power Supply Sequencing, Board-Level Glue Logic Replacement, Motor Drive Control Logic, Display and Camera Interface Bridging, Legacy Interface Emulation (PCI, VME, ISA).
I/O Expansion for Microcontrollers
The 5M160ZT100C4N's 79 user I/Os and 160 logic elements make it a strong fit for I/O expansion around mid-range microcontrollers that lack sufficient GPIO or peripheral channels. The 7.9 ns pin-to-pin delay supports bit-banged protocol bridging at up to 125 MHz, while the 1.2-3.3 V VCCIO range directly interfaces 1.8 V and 3.3 V MCU banks without level shifters. The 8 Kbit UFM block stores board-level configuration such as board revision and serial number. JTAG-based ISP enables reconfiguration in the field, eliminating the need for an external boot flash.
Recomendado
Bus Bridging and Address Decoding
Glue logic for bridging between legacy and modern buses - for example, decoding 16-bit ISA addresses, multiplexing address/data buses on a 386EX, or aggregating interrupts from multiple peripherals - is a canonical CPLD task. The 5M160ZT100C4N's 128 macrocells can implement a full 24-bit address decoder plus 8-16 chip-select outputs in a single device. The non-volatile flash configuration delivers instant-on behaviour with no boot delay, critical for systems where the CPU cannot tolerate additional latency. The JTAG chain allows boundary-scan test of the entire decoding network during production.
Recomendado
Power Supply Sequencing
The 5M160ZT100C4N is widely deployed as a multi-rail power sequencer for ATCA, telecom, and server blades where 6-12 supply rails must be brought up in a specific order with controlled rise times. The 79 user I/Os are typically configured as ENABLE/PGOOD pairs driving external MOSFET controllers, while the 8 Kbit UFM stores the sequencing order and timing constants. The 7.9 ns tPD is fast enough to respond to a PGOOD fault within one switching cycle. The flash-based instant-on feature prevents a hung state at power-up if the configuration is valid.
Recomendado
Board-Level Glue Logic Replacement
Designers replacing 4-8 discrete 74LS/74HC/74FCT TTL packages with a single CPLD gain PCB area, BOM simplification, and easier ECO turnaround. The 5M160ZT100C4N provides 128 macrocells, equivalent to roughly 200-300 discrete TTL gates, in a single 100-pin TQFP. The flash-based configuration means no socketed PROMs and no error-prone resistor pull-ups. JTAG-based in-system programming enables board-level rework without removing the device, a major benefit in prototype and low-volume manufacturing.
Recomendado
Motor Drive Control Logic
In industrial motor drives and robotics controllers, the 5M160ZT100C4N handles the digital control plane: PWM dead-band generation, Hall-sensor decoding, encoder quadrature processing, and fault aggregation. The 7.9 ns tPD enables 100 kHz PWM with sub-microsecond dead-time control. The 1.2-3.3 V VCCIO range interfaces directly to modern MCU control signals, while the 5 V-tolerant inputs (with external clamping) accept legacy Hall-sensor logic. For deployments beyond 85 C, the 5M160ZT100I5N industrial variant is recommended.
Recomendado
Display and Camera Interface Bridging
The 5M160ZT100C4N bridges parallel RGB, LVDS flat-panel, and CMOS camera interfaces to host processors that lack the right combination of I/O voltage and pin count. The 79 user I/Os accommodate a 24-bit color bus plus control signals with margin, while the 1.2-3.3 V VCCIO range supports both 1.8 V host processors and 3.3 V display panels. The 7.9 ns tPD sustains pixel clocks up to 125 MHz, sufficient for XGA (1024x768) at 60 Hz refresh. The non-volatile configuration boots in <1 ms, eliminating panel flicker on power-up.
Recomendado
Legacy Interface Emulation (PCI, VME, ISA)
Many long-lifecycle industrial systems still ship with PCI, VMEbus, or ISA buses that the latest microcontrollers and ASICs no longer support natively. The 5M160ZT100C4N emulates the missing bus handshakes, parity generation, and interrupt acknowledge sequences in 160 logic elements with deterministic 7.9 ns timing. The 100-pin TQFP footprint retains pin compatibility with older 5 V-tolerant glue logic while supporting 3.3 V VCCIO, and the in-system programmability enables field upgrades when legacy interface specifications change.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para 5M160ZT100C4N — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | 5M160ZT100C5N | 5M160ZT100A5N | 5M160ZT100I5N | 5M1270ZT144C4N | 5M160ZM100C4N |
|---|---|---|---|---|---|---|
| Brand | Intel | Intel | Intel | Intel | Intel | Intel |
| Package | TQFP-100 (100-pin) | TQFP-100 (100-pin) - same | TQFP-100 (100-pin) - same | TQFP-100 (100-pin) - same | TQFP-144 (144-pin) - larger | MBGA-100 (100-ball) - same pin count, different package |
| Logic Elements | 160 | 160 - same | 160 - same | 160 - same | 1270 (+694%) | 160 - same |
| Macrocells | 128 | 128 - same | 128 - same | 128 - same | 980 (+665%) | 128 - same |
| User I/Os | 79 | 79 - same | 79 - same | 79 - same | 100+ (more) | 79 - same |
| Pin-to-Pin Delay (tPD) | 7.9 ns (grade 7) | 8.5 ns (grade 5) - 8% slower | 5.5 ns (grade 5) - 30% faster | 5.5 ns (grade 5) - 30% faster | 6.2 ns (grade 7) - 22% faster | 7.9 ns (grade 7) - same |
| Operating Temperature | 0 C to +85 C (commercial) | 0 C to +85 C (commercial) - same | -40 C to +100 C (industrial) | -40 C to +100 C (industrial) | 0 C to +85 C (commercial) - same | 0 C to +85 C (commercial) - same |
| VCCIO Range | 1.2 V to 3.3 V | 1.2 V to 3.3 V - same | 1.2 V to 3.3 V - same | 1.2 V to 3.3 V - same | 1.2 V to 3.3 V - same | 1.2 V to 3.3 V - same |
| User Flash Memory (UFM) | 8 Kbits | 8 Kbits - same | 8 Kbits - same | 8 Kbits - same | 8 Kbits - same | 8 Kbits - same |
Principais diferenciais
- Instant-on operation with no boot flash required (vs 5M1270ZT144C4N)
- Compact 100-pin TQFP with 79 user I/Os (vs 5M160ZM100C4N (MBGA-100))
- Cost-optimized C4N speed grade (vs 5M160ZT100A5N (grade 5))
Notas de projeto
The 5M160ZT100C4N requires a single 1.8 V VCCINT supply for the core logic and an independent VCCIO rail per bank, programmable from 1.2 V to 3.3 V. Place a 100 nF decoupling capacitor within 3 mm of every VCCINT pin and a 4.7 uF bulk capacitor at the regulator output. Each VCCIO bank must have its own 100 nF decoupling; do not share capacitors across banks. According to the MAX V Family datasheet, power-up sequencing requires VCCINT to rise before VCCIO, or simultaneously, with a maximum delta of 200 mV. In-system programming via JTAG (TCK, TMS, TDI, TDO) is the recommended configuration interface.
Estimated: the 100-pin TQFP package has theta_JA of approximately 35 C/W on a JEDEC EIA/JESD51 4-layer test board with 2 oz copper. At maximum continuous operation (commercial grade 85 C ambient) with full I/O toggle, internal dissipation is well below 500 mW, giving a junction temperature rise of <18 C - comfortable headroom. For designs mounted in a sealed enclosure without forced airflow, add thermal vias under the exposed pad region (the T100 has no exposed pad, but adding a copper flood on top and bottom layers improves heat spreading). Industrial variants (I-grade, 100 C) require the same thermal analysis but with a 100 C ambient baseline.
Route all JTAG signals (TCK, TMS, TDI, TDO) as a bus with matched lengths within 25 mm and a 10 kohm pull-up on TCK and TMS. Place the JTAG connector at the edge of the PCB for easy programming access during production test. The 79 user I/Os can be assigned to any bank; for high-speed interfaces, keep switching signals within one bank to avoid VCCIO crossings. According to MAX V PCB design guidelines, keep clock and high-speed signal traces over a continuous ground plane and use 45-degree bends only. Route differential pairs with 100 ohm differential impedance if using LVDS.
Three pitfalls are most commonly observed: (1) tying the JTAG TMS and TCK pins to GND instead of pulling them up via 10 kohm - this prevents ISP. (2) Driving I/Os before VCCIO has ramped - outputs can crowbar and damage the device; ensure power sequencing matches datasheet Figure 7-1. (3) Exceeding the UFM endurance specification of 1000 program/erase cycles when storing frequently updated calibration data - consider an external EEPROM if the design requires field updates more than 1000 times. Source: MAX V Family datasheet, AN-491 design guide.
Informações de conformidade
RoHS compliant and lead-free per Intel product declaration. AEC-Q100 qualification not applicable for commercial-grade CPLD; industrial-grade variant (5M160ZT100I5N) is also not AEC-Q100 qualified - for automotive applications, consult Intel MAX V automotive-grade part numbers.
