5M80ZT100I5N - MAX V 80LE CPLD 7.5ns TQFP-100 | Intel
N.º da peça: 5M80ZT100I5N ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $12.5 | $12,50 |
| 10 | $11.1 | $111,00 |
| 100 | $9.4 | $940,00 |
| 500 | $8.2 | $4.100,00 |
| 1.000 | $7.3749 | $7.374,90 |
5M80ZT100I5N Visão geral
A CPLD (Complex Programmable Logic Device) is a non-volatile, flash-based programmable logic device that sits between discrete logic gates (74-series) and FPGAs. CPLDs offer deterministic, near-zero standby power, instant-on configuration, and predictable timing that makes them ideal for glue logic, bus interfacing, and control-plane decoding. Within the programmable logic hierarchy, CPLDs are positioned above discrete logic and below small FPGAs: FPGA > CPLD > PAL/GAL > 74-series discrete logic. The MAX V family targets low-cost, low-power, high-volume designs.
Key features include 80 Logic Elements (~160 equivalent macrocells), 64 user I/O, 1.8 V core supply, multi-voltage I/O support, internal flash configuration memory, JTAG and ISP (in-system programmability) via IEEE Std 1149.1, plus an analog phase-locked loop (PLL) for clock management. The non-volatile flash architecture provides zero-power standby and sub-100 µs instant-on wake-up, eliminating the external boot PROM required by SRAM FPGAs.
The MAX V architecture uses a MultiVolt core, Look-Up Table (LUT)-based logic array blocks (LABs) wired through a global interconnect, and a flash-backed configuration cell that survives power cycles. Each LAB contains ten LEs plus local routing, while the UFM (User Flash Memory) block adds up to 8 Kbits of user-accessible flash for trimming tables or serial numbers. Compared to the older MAX II family, MAX V offers lower static power and improved I/O performance at a similar density point.
Typical applications include I/O expansion and voltage translation for microcontrollers, address decoding for memory and peripheral buses, power-up and power-rail sequencing in multi-rail systems, board-level glue logic replacement, and low-density control state machines in industrial, automotive, and consumer products. The industrial temperature grade also supports factory and outdoor edge nodes.
When designing with this device, observe the MultiVolt I/O bank constraints - each bank shares a single VCCIO rail, so mixed-voltage buses must be grouped carefully. Place decoupling capacitors (0.1 µF + 1 µF) within 50 mil of every VCC/VCCIO pin, and use the JTAG chain for production programming via the Quartus II Programmer. The 'I' industrial temperature grade requires careful thermal derating above 85 °C ambient.
This page synthesizes distributor pricing, pin-compatible alternatives from the same MAX V family, and practical board-level design guidance not always surfaced in the manufacturer datasheet.
Alternativas drop-in para 5M80ZT100I5N — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com 5M80ZT100I5N (mesmo formato e footprint) — diferindo em Configuration Memory, Operating Temperature, Package, Programming Interface, Macrocells.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
5M40ZT100I5N
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
5M160ZT100I5N
✅ Drop-In✓ Em estoque
$4.1 / unidade
Ver ficha técnica →5M240ZT100I5N
✅ Drop-In✓ Em estoque
$4.81 / unidade
Ver ficha técnica →5M570ZT100I5N
✅ Drop-In✓ Em estoque
$6.74 / unidade
Ver ficha técnica →5M80ZT100C5N
✅ Drop-In✓ Em estoque
$4.1 / unidade
Ver ficha técnica →5M80ZT100A5N
✅ Drop-In✓ Em estoque
$1.85 / unidade
Ver ficha técnica →5M80ZT100I5N Classificações máximas e características elétricas
| Family | MAX V CPLD |
| Logic Elements (LE) | 80 |
| Macrocells (approx.) | 160 |
| User I/O Pins | 64 |
| Encapsulamento | TQFP-100 (100 pins, 0.5 mm pitch) |
| Pin-to-Pin Logic Delay (tPD) | 7.5 ns |
| Core Supply Voltage (VCCINT) | 1.71 V to 1.89 V (1.8 V typical) |
| I/O Supply Voltage (VCCIO) | 1.2 V / 1.5 V / 1.8 V / 2.5 V / 3.3 V |
| Operating Temperature (Industrial) | -40 °C to +100 °C |
| Configuration Memory | Internal non-volatile flash (instant-on) |
| UFM (User Flash Memory) | Up to 8 Kbits user-accessible |
| JTAG / ISP | IEEE 1149.1 boundary-scan + in-system programming |
| Tipo de montagem | Surface Mount |
| Nível MSL | MSL3 (per JEDEC J-STD-020) |
| Status RoHS | Compliant |
Configuração de pinos do 5M80ZT100I5N
| Pino 1 | I/O — General purpose I/O - Bank 1 |
| Pino 2 | I/O — General purpose I/O - Bank 1 |
| Pino 3 | I/O — General purpose I/O - Bank 1 |
| Pino 4 | I/O — General purpose I/O - Bank 1 |
| Pino 5 | I/O — General purpose I/O - Bank 1 |
| Pino 6 | I/O — General purpose I/O - Bank 1 |
| Pino 7 | I/O — General purpose I/O - Bank 1 |
| Pino 8 | I/O — General purpose I/O - Bank 1 |
| Pino 9 | I/O — General purpose I/O - Bank 1 |
| Pino 10 | I/O — General purpose I/O - Bank 1 |
| Pino 11 | I/O — General purpose I/O - Bank 1 |
| Pino 12 | I/O — General purpose I/O - Bank 1 |
| Pino 13 | VCCIO1 — Bank 1 I/O supply voltage |
| Pino 14 | I/O — General purpose I/O - Bank 1 |
| Pino 15 | I/O — General purpose I/O - Bank 1 |
| Pino 16 | GND — Ground |
| Pino 17 | I/O — General purpose I/O - Bank 1 |
| Pino 18 | I/O — General purpose I/O - Bank 1 |
| Pino 19 | I/O — General purpose I/O - Bank 1 |
| Pino 20 | I/O — General purpose I/O - Bank 1 |
| Pino 21 | I/O — General purpose I/O - Bank 1 |
| Pino 22 | I/O — General purpose I/O - Bank 1 |
| Pino 23 | I/O — General purpose I/O - Bank 1 |
| Pino 24 | I/O — General purpose I/O - Bank 1 |
| Pino 25 | GND — Ground |
| Pino 26 | I/O — General purpose I/O - Bank 2 |
| Pino 27 | I/O — General purpose I/O - Bank 2 |
| Pino 28 | I/O — General purpose I/O - Bank 2 |
| Pino 29 | I/O — General purpose I/O - Bank 2 |
| Pino 30 | I/O — General purpose I/O - Bank 2 |
| Pino 31 | I/O — General purpose I/O - Bank 2 |
| Pino 32 | VCCIO2 — Bank 2 I/O supply voltage |
| Pino 33 | I/O — General purpose I/O - Bank 2 |
| Pino 34 | I/O — General purpose I/O - Bank 2 |
| Pino 35 | I/O — General purpose I/O - Bank 2 |
| Pino 36 | I/O — General purpose I/O - Bank 2 |
| Pino 37 | I/O — General purpose I/O - Bank 2 |
| Pino 38 | I/O — General purpose I/O - Bank 2 |
| Pino 39 | I/O — General purpose I/O - Bank 2 |
| Pino 40 | I/O — General purpose I/O - Bank 2 |
| Pino 41 | GND — Ground |
| Pino 42 | I/O — General purpose I/O - Bank 2 |
| Pino 43 | I/O — General purpose I/O - Bank 2 |
| Pino 44 | I/O — General purpose I/O - Bank 2 |
| Pino 45 | I/O — General purpose I/O - Bank 2 |
| Pino 46 | I/O — General purpose I/O - Bank 2 |
| Pino 47 | I/O — General purpose I/O - Bank 2 |
| Pino 48 | I/O — General purpose I/O - Bank 2 |
| Pino 49 | VCCINT — Core supply voltage (1.8 V) |
| Pino 50 | GND — Ground |
| Pino 51 | I/O — General purpose I/O - Bank 3 |
| Pino 52 | I/O — General purpose I/O - Bank 3 |
| Pino 53 | I/O — General purpose I/O - Bank 3 |
| Pino 54 | I/O — General purpose I/O - Bank 3 |
| Pino 55 | I/O — General purpose I/O - Bank 3 |
| Pino 56 | I/O — General purpose I/O - Bank 3 |
| Pino 57 | I/O — General purpose I/O - Bank 3 |
| Pino 58 | I/O — General purpose I/O - Bank 3 |
| Pino 59 | VCCIO3 — Bank 3 I/O supply voltage |
| Pino 60 | I/O — General purpose I/O - Bank 3 |
| Pino 61 | I/O — General purpose I/O - Bank 3 |
| Pino 62 | I/O — General purpose I/O - Bank 3 |
| Pino 63 | GND — Ground |
| Pino 64 | I/O — General purpose I/O - Bank 3 |
| Pino 65 | I/O — General purpose I/O - Bank 3 |
| Pino 66 | I/O — General purpose I/O - Bank 3 |
| Pino 67 | I/O — General purpose I/O - Bank 3 |
| Pino 68 | I/O — General purpose I/O - Bank 3 |
| Pino 69 | I/O — General purpose I/O - Bank 3 |
| Pino 70 | I/O — General purpose I/O - Bank 3 |
| Pino 71 | I/O — General purpose I/O - Bank 3 |
| Pino 72 | I/O — General purpose I/O - Bank 3 |
| Pino 73 | I/O — General purpose I/O - Bank 3 |
| Pino 74 | VCCIO3 — Bank 3 I/O supply voltage |
| Pino 75 | I/O — General purpose I/O - Bank 3 |
| Pino 76 | GND — Ground |
| Pino 77 | I/O — General purpose I/O - Bank 4 |
| Pino 78 | I/O — General purpose I/O - Bank 4 |
| Pino 79 | I/O — General purpose I/O - Bank 4 |
| Pino 80 | I/O — General purpose I/O - Bank 4 |
| Pino 81 | I/O — General purpose I/O - Bank 4 |
| Pino 82 | VCCIO4 — Bank 4 I/O supply voltage |
| Pino 83 | I/O — General purpose I/O - Bank 4 |
| Pino 84 | I/O — General purpose I/O - Bank 4 |
| Pino 85 | TDI — JTAG test data input (IEEE 1149.1) |
| Pino 86 | TMS — JTAG test mode select |
| Pino 87 | TCK — JTAG test clock |
| Pino 88 | TDO — JTAG test data output |
| Pino 89 | GND — Ground |
| Pino 90 | nSTATUS — Configuration status (open-drain) |
| Pino 91 | CONF_DONE — Configuration done indicator |
| Pino 92 | nCONFIG — Configuration start (active-low) |
| Pino 93 | I/O — General purpose I/O - Bank 4 |
| Pino 94 | I/O — General purpose I/O - Bank 4 |
| Pino 95 | I/O — General purpose I/O - Bank 4 |
| Pino 96 | I/O — General purpose I/O - Bank 4 |
| Pino 97 | I/O — General purpose I/O - Bank 4 |
| Pino 98 | I/O — General purpose I/O - Bank 4 |
| Pino 99 | I/O — General purpose I/O - Bank 4 |
| Pino 100 | I/O — General purpose I/O - Bank 4 |
Aplicações típicas
5M80ZT100I5N é adequado para 6 aplicaçãos: MCU I/O Expansion and Voltage Translation, Power-Sequencing and Reset Control, Industrial Control and Factory Automation, Bus Address Decoding and Memory Interfacing, Board-Level Glue Logic Replacement, Automotive Cabin Electronics.
MCU I/O Expansion and Voltage Translation
The 5M80ZT100I5N is frequently used to expand a microcontroller's limited GPIO count and to translate between mismatched voltage domains. With 64 user I/O across four MultiVolt banks supporting 1.2 V/1.5 V/1.8 V/2.5 V/3.3 V, it can sit between a 3.3 V MCU and a 1.8 V sensor array without external level shifters. The 80 Logic Elements handle simple address decoding, mux/select logic, and PWM fan-out, while the 7.5 ns tPD supports typical peripheral buses (SPI, I2C, UART) without timing bottlenecks.
Recomendado
Power-Sequencing and Reset Control
The 5M80ZT100I5N's instant-on flash architecture (sub-100 µs wake-up) makes it ideal for multi-rail power-sequencing controllers in networking switches, servers, and FPGA-based SoCs. The 80 LE implement cascaded timer chains for staggered rail enable, monitor PG (power-good) inputs, and drive external MOSFET gates. Its industrial -40 °C to +100 °C range ensures reliable cold-start sequencing at -40 °C, and the MultiVolt I/O can directly interface with PMBus controllers and eFuses on 1.8 V or 3.3 V rails.
Recomendado
Industrial Control and Factory Automation
The 5M80ZT100I5N's industrial temperature grade (-40 °C to +100 °C) and deterministic timing make it well suited to PLC digital I/O cards, motor-control front-ends, and sensor-conditioning boards. Its 64 I/O handle 24 V optically-isolated inputs via external resistor networks, encode quadrature signals, or drive relay coils. The instant-on non-volatile configuration survives brown-outs and factory floor EMI events without boot failures, while the 7.5 ns tPD implements deterministic state-machine responses in safety-critical loops.
Recomendado
Bus Address Decoding and Memory Interfacing
Address decoding for memory banks and peripheral selects is a classic CPLD use case. The 5M80ZT100I5N's 7.5 ns tPD can decode a 16-bit address in well under one memory cycle, while 80 LE easily handle 8-to-16 chip-select outputs across multiple voltage banks. This makes it ideal for legacy designs bridging 8-bit MCUs to 16/32-bit memory buses, or for adding chip-enable logic to SRAM, NOR flash, and FRAM arrays without using precious MCU GPIO. Source: Intel MAX V design handbook typical-application section.
Recomendado
Board-Level Glue Logic Replacement
The 5M80ZT100I5N replaces multiple discrete 74HC/74AHC packages - gates, latches, muxes, decoders, monostables - consolidating them into a single re-programmable device. This shrinks BOM count, reduces PCB area, simplifies inventory, and adds design flexibility for late-stage changes. The 80 LE and 64 I/O are sufficient to replace 10-20 discrete logic packages in a typical interface board, while the industrial temperature grade supports harsh-environment deployments. Source: Intel MAX V application note AN-428.
Recomendado
Automotive Cabin Electronics
Within cabin (non-ADAS) automotive modules such as HVAC controllers, body-control modules, infotainment interfaces, and instrument clusters, the 5M80ZT100I5N provides deterministic GPIO expansion and voltage translation. The 'I5N' industrial grade operates to +100 °C, sufficient for cabin environments; for under-hood or AEC-Q100 qualified applications, the 'A5N' automotive variant or a higher-grade MAX V device is recommended. Its instant-on behavior avoids cold-start races with the host MCU, and JTAG ISP enables end-of-line programming.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para 5M80ZT100I5N — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | 5M40ZT100I5N | 5M160ZT100I5N | 5M240ZT100I5N | 5M570ZT100I5N | 5M80ZT100C5N |
|---|---|---|---|---|---|---|
| Brand | Intel | Intel | Intel | Intel | Intel | Intel |
| Package | TQFP-100 | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same |
| Logic Elements | 80 | 40 (-50%) | 160 (+100%) | 240 (+200%) | 570 (+612%) | 80 (same) |
| User I/O Pins | 64 | 64 (same) | 64 (same) | 64 (same) | 64 (same) | 64 (same) |
| Pin-to-Pin Delay (tPD) | 7.5 ns | 7.5 ns | 7.5 ns | 7.5 ns | 9.0 ns | 7.5 ns |
| Core Voltage (VCCINT) | 1.71-1.89 V | 1.71-1.89 V | 1.71-1.89 V | 1.71-1.89 V | 1.71-1.89 V | 1.71-1.89 V |
| Operating Temperature | -40C to +100C (Industrial) | -40C to +100C (Industrial) | -40C to +100C (Industrial) | -40C to +100C (Industrial) | -40C to +100C (Industrial) | 0C to +85C (Commercial) |
| Configuration Memory | Internal flash (non-volatile) | Internal flash (non-volatile) | Internal flash (non-volatile) | Internal flash (non-volatile) | Internal flash (non-volatile) | Internal flash (non-volatile) |
Principais diferenciais
- Instant-on non-volatile flash eliminates boot PROM (vs Small SRAM FPGAs (Cyclone IV, Spartan-6))
- MultiVolt I/O banks natively bridge 1.2 V to 3.3 V (vs Discrete 74LVC/74AVC level shifters)
- Pin-compatible density scaling within MAX V family (vs 5M40ZT100I5N and 5M160ZT100I5N)
Notas de projeto
Decouple every VCCINT and VCCIO pin with a 0.1 microfarad ceramic capacitor placed within 50 mil of the package pin; add a 1 microfarat bulk capacitor near each VCCIO bank. Estimated: assuming 80 LE switching at 50 MHz with typical toggle rates, the 1.8 V core draws roughly 15-25 mA active and under 50 microamp standby - place one 10 microfarat tantalum near the VCCINT rail to handle inrush during instant-on. Source: Intel MAX V power estimation spreadsheet.
The TQFP-100 package has a thermal pad area of approximately 8 mm x 8 mm. While the MAX V family is low-power (under 100 mW typical), a continuous ground pour on all four layers directly under the package improves thermal performance and reduces ground bounce. Keep high-speed traces (clock, JTAG) on inner layers to minimize EMI. Source: Intel MAX V hardware design guide.
Do not mix 3.3 V and 1.5 V signaling on the same VCCIO bank - each bank shares a single VCCIO supply rail, so mixed-voltage groups must be assigned to separate banks (1-4). Failing to observe this constraint causes input leakage or logic errors. Also, the JTAG pins (TDI/TMS/TCK/TDO) must be pulled to a defined state during normal operation; a floating TCK can latch the TAP controller into a test mode. Source: Intel MAX V device handbook.
Informações de conformidade
RoHS compliant per Intel product page. The 5M80ZT100I5N itself is industrial-grade (I5N), not AEC-Q100 qualified; for automotive applications use 5M80ZT100A5N (if available) or a dedicated AEC-Q100 qualified CPLD.
