5M80ZT100A5N - 64-Macrocell MAX V CPLD, 100-TQFP, 1.8V | Altera
N.º da peça: 5M80ZT100A5N ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $2.95 | $2,95 |
| 10 | $2.65 | $26,50 |
| 100 | $2.3 | $230,00 |
| 500 | $2.05 | $1.025,00 |
| 1.000 | $1.85 | $1.850,00 |
5M80ZT100A5N Visão geral
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that bridges the gap between simple PLDs and larger FPGAs. In the broader programmable logic taxonomy, CPLDs sit between PAL/GAL (small, simple) and FPGAs (large, register-rich, volatile SRAM-based). MAX V CPLDs use a flash-based configuration cell that retains bitstream without an external boot PROM, which simplifies board design and reduces BOM cost versus SRAM-based FPGAs. The 5M80ZT100A5N therefore occupies a 'low-density, instant-on, deterministic-timing' niche well above discrete 74HC logic but below the smallest Cyclone FPGA.
Key features include 64 logic macrocells (each containing a 36-input product term and one flip-flop), 80 user I/O pins on the TQFP-100 package, an integrated 1.8 V core with 1.8 V/2.5 V/3.3 V multi-voltage I/O support through bank-level VCCIO rails, and an embedded user flash memory block (UFM) of 8 Kbits that can be used for configuration storage or general-purpose non-volatile data. The device supports in-system programmability via JTAG (IEEE 1149.1) and operates across the industrial -40 C to +125 C junction temperature range. The 1.8 V core core voltage combined with the legacy 3.3 V/2.5 V I/O bank options makes the 5M80ZT100A5N a practical 'bridge' between modern low-voltage processors and older peripheral ICs.
The 5M80ZT100A5N's 7.5 ns tPD and deterministic 118.3 MHz fMAX suit it for bus-interface decoding, address latch/buffer logic, asynchronous state machines, and small FIFO glue. The MAX V architecture uses a uniform interconnect matrix with predictable routing delays, so timing closure does not require place-and-route iteration as with FPGAs - timing is largely data-sheet-driven.
Typical applications include industrial control boards (sensor aggregation, motor-driver interface decoding), automotive body-electronics modules (AEC-Q100 qualified variants exist in this family), consumer-electronics glue logic between ASSPs and I/O connectors, and any system requiring instant-on, non-volatile logic with sub-10 ns decode paths. A common pattern is replacing 4-8 discrete 74-series packages with a single 5M80ZT100A5N to free PCB area and reduce assembly cost.
When designing with this part, choose VCCIO per bank based on the connected peripherals (1.8 V, 2.5 V, or 3.3 V), connect JTAG TMS/TCK/TDO/TDI to a header for in-system programming, and provide a clean 1.8 V core supply (VCCINT) with at least one 0.1 uF decoupling capacitor per supply pin. The Quartus II / Quartus Prime toolchain generates the JEDEC programming file. Note that MAX V devices are mature - newer MAX 10 / MAX II families may be considered if higher logic density is needed, but they are not pin-compatible with this TQFP-100 footprint.
Alternativas drop-in para 5M80ZT100A5N — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com 5M80ZT100A5N (mesmo formato e footprint) — diferindo em Configuration Memory, Package, Programming Interface, User Flash Memory, I/O Voltage (VCCIO).
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
5M80ZT100I5N
✅ Drop-In✓ Em estoque
$7.3749 / unidade
Ver ficha técnica →5M80ZT100C5N
✅ Drop-In✓ Em estoque
$4.1 / unidade
Ver ficha técnica →5M160ZT100A5N
✅ Drop-In✓ Em estoque
$4.9 / unidade
Ver ficha técnica →5M240ZT100A5N
✅ Drop-In✓ Em estoque
$6.1 / unidade
Ver ficha técnica →5M570ZT100A5N
✅ Drop-In✓ Em estoque
$9.75 / unidade
Ver ficha técnica →5M80ZT100A5N Classificações máximas e características elétricas
| Family | MAX V |
| Macro Cells | 64 |
| Logic Elements / LABs | 8 Logic Array Blocks (LABs) |
| Maximum User I/O | 80 (in TQFP-100 package) |
| Pin-to-Pin Propagation Delay (tPD) | 7.5 ns |
| Maximum Internal Frequency (fMAX) | 118.3 MHz |
| Core Supply Voltage (VCCINT) | 1.8 V |
| I/O Bank Supply Voltage (VCCIO) | 1.2 V / 1.5 V / 1.8 V / 2.5 V / 3.3 V (multi-voltage banks) |
| User Flash Memory (UFM) | 8 Kbits (typical for MAX V 64-macrocell device) |
| Configuration Memory | Non-volatile, on-chip flash |
| Programming Interface | JTAG (IEEE 1149.1 / IEEE 1532) |
| Temperatura de junção de operação | -40 C to +125 C (automotive/industrial grade) |
| Encapsulamento | 100-pin TQFP (T100) |
| Tipo de montagem | Surface Mount |
| Nível MSL | 3 (per JEDEC J-STD-020) |
| Status RoHS | Compliant |
| Automotive Qualification | AEC-Q100 (A5N suffix) |
| Global Clock Networks | 4 |
| Lead-Free / Halogen-Free | Yes / Yes (per Altera lead-free roadmap) |
Configuração de pinos do 5M80ZT100A5N
| Pino 1 | I/O — General-purpose user I/O (bank 3) |
| Pino 2 | I/O — General-purpose user I/O (bank 3) |
| Pino 3 | I/O — General-purpose user I/O (bank 3) |
| Pino 4 | I/O — General-purpose user I/O (bank 3) |
| Pino 5 | I/O — General-purpose user I/O (bank 3) |
| Pino 6 | I/O — General-purpose user I/O (bank 3) |
| Pino 7 | VCCIO3 — I/O bank 3 supply voltage |
| Pino 8 | I/O — General-purpose user I/O (bank 3) |
| Pino 9 | I/O — General-purpose user I/O (bank 3) |
| Pino 10 | GND — Ground |
| Pino 11 | I/O — General-purpose user I/O (bank 3) |
| Pino 12 | I/O — General-purpose user I/O (bank 3) |
| Pino 13 | I/O — General-purpose user I/O (bank 3) |
| Pino 14 | I/O — General-purpose user I/O (bank 3) |
| Pino 15 | I/O — General-purpose user I/O (bank 3) |
| Pino 16 | I/O — General-purpose user I/O (bank 3) |
| Pino 17 | I/O — General-purpose user I/O (bank 3) |
| Pino 18 | I/O — General-purpose user I/O (bank 3) |
| Pino 19 | VCCINT — Core supply voltage 1.8 V |
| Pino 20 | I/O — General-purpose user I/O (bank 3) |
| Pino 21 | I/O — General-purpose user I/O (bank 3) |
| Pino 22 | GND — Ground |
| Pino 23 | I/O — General-purpose user I/O (bank 3) |
| Pino 24 | I/O — General-purpose user I/O (bank 3) |
| Pino 25 | I/O — General-purpose user I/O (bank 3) |
| Pino 26 | I/O — General-purpose user I/O (bank 3) |
| Pino 27 | I/O — General-purpose user I/O (bank 3) |
| Pino 28 | I/O — General-purpose user I/O (bank 3) |
| Pino 29 | I/O — General-purpose user I/O (bank 3) |
| Pino 30 | I/O — General-purpose user I/O (bank 3) |
| Pino 31 | GND — Ground |
| Pino 32 | I/O — General-purpose user I/O (bank 3) |
| Pino 33 | I/O — General-purpose user I/O (bank 3) |
| Pino 34 | I/O — General-purpose user I/O (bank 3) |
| Pino 35 | VCCIO3 — I/O bank 3 supply voltage |
| Pino 36 | I/O — General-purpose user I/O (bank 3) |
| Pino 37 | I/O — General-purpose user I/O (bank 3) |
| Pino 38 | I/O — General-purpose user I/O (bank 3) |
| Pino 39 | I/O — General-purpose user I/O (bank 3) |
| Pino 40 | TDI — JTAG Test Data In |
| Pino 41 | TMS — JTAG Test Mode Select |
| Pino 42 | TCK — JTAG Test Clock |
| Pino 43 | GND — Ground |
| Pino 44 | TDO — JTAG Test Data Out |
| Pino 45 | I/O — General-purpose user I/O (bank 4) |
| Pino 46 | I/O — General-purpose user I/O (bank 4) |
| Pino 47 | I/O — General-purpose user I/O (bank 4) |
| Pino 48 | I/O — General-purpose user I/O (bank 4) |
| Pino 49 | I/O — General-purpose user I/O (bank 4) |
| Pino 50 | I/O — General-purpose user I/O (bank 4) |
| Pino 51 | GND — Ground |
| Pino 52 | I/O — General-purpose user I/O (bank 4) |
| Pino 53 | I/O — General-purpose user I/O (bank 4) |
| Pino 54 | VCCIO4 — I/O bank 4 supply voltage |
| Pino 55 | I/O — General-purpose user I/O (bank 4) |
| Pino 56 | I/O — General-purpose user I/O (bank 4) |
| Pino 57 | I/O — General-purpose user I/O (bank 4) |
| Pino 58 | I/O — General-purpose user I/O (bank 4) |
| Pino 59 | I/O — General-purpose user I/O (bank 4) |
| Pino 60 | I/O — General-purpose user I/O (bank 4) |
| Pino 61 | GND — Ground |
| Pino 62 | I/O — General-purpose user I/O (bank 4) |
| Pino 63 | I/O — General-purpose user I/O (bank 4) |
| Pino 64 | I/O — General-purpose user I/O (bank 4) |
| Pino 65 | I/O — General-purpose user I/O (bank 4) |
| Pino 66 | VCCINT — Core supply voltage 1.8 V |
| Pino 67 | I/O — General-purpose user I/O (bank 4) |
| Pino 68 | I/O — General-purpose user I/O (bank 4) |
| Pino 69 | I/O — General-purpose user I/O (bank 4) |
| Pino 70 | I/O — General-purpose user I/O (bank 4) |
| Pino 71 | I/O — General-purpose user I/O (bank 4) |
| Pino 72 | GND — Ground |
| Pino 73 | I/O — General-purpose user I/O (bank 1) |
| Pino 74 | I/O — General-purpose user I/O (bank 1) |
| Pino 75 | VCCIO1 — I/O bank 1 supply voltage |
| Pino 76 | I/O — General-purpose user I/O (bank 1) |
| Pino 77 | I/O — General-purpose user I/O (bank 1) |
| Pino 78 | I/O — General-purpose user I/O (bank 1) |
| Pino 79 | I/O — General-purpose user I/O (bank 1) |
| Pino 80 | I/O — General-purpose user I/O (bank 1) |
| Pino 81 | I/O — General-purpose user I/O (bank 1) |
| Pino 82 | GND — Ground |
| Pino 83 | I/O — General-purpose user I/O (bank 1) |
| Pino 84 | I/O — General-purpose user I/O (bank 1) |
| Pino 85 | I/O — General-purpose user I/O (bank 1) |
| Pino 86 | I/O — General-purpose user I/O (bank 1) |
| Pino 87 | I/O — General-purpose user I/O (bank 1) |
| Pino 88 | I/O — General-purpose user I/O (bank 1) |
| Pino 89 | I/O — General-purpose user I/O (bank 1) |
| Pino 90 | I/O — General-purpose user I/O (bank 1) |
| Pino 91 | GND — Ground |
| Pino 92 | I/O — General-purpose user I/O (bank 1) |
| Pino 93 | I/O — General-purpose user I/O (bank 1) |
| Pino 94 | I/O — General-purpose user I/O (bank 2) |
| Pino 95 | I/O — General-purpose user I/O (bank 2) |
| Pino 96 | I/O — General-purpose user I/O (bank 2) |
| Pino 97 | VCCIO2 — I/O bank 2 supply voltage |
| Pino 98 | I/O — General-purpose user I/O (bank 2) |
| Pino 99 | I/O — General-purpose user I/O (bank 2) |
| Pino 100 | I/O — General-purpose user I/O (bank 2) |
Aplicações típicas
5M80ZT100A5N é adequado para 6 aplicaçãos: Industrial Control Board Glue Logic, Automotive Body Electronics Module, Consumer Electronics Interface Bridge, Motor Driver Interface Decoder, Communications Equipment Glue Logic, Test and Measurement Front-End Logic.
Industrial Control Board Glue Logic
The 5M80ZT100A5N replaces 4-8 discrete 74HC/74LVC logic packages on industrial PLC and sensor-aggregation boards, freeing PCB area while delivering 7.5 ns tPD for fast bus-decoder paths. Its 1.8 V core with multi-voltage I/O banks bridges a modern ARM Cortex-M0 host processor (1.8 V GPIO) to legacy 3.3 V and 5 V-tolerant peripherals without external level shifters. The -40 C to +125 C junction temperature range and AEC-Q100 'A5N' suffix suit factory-floor and outdoor cabinet deployments where temperature swings and vibration stress rule out consumer-grade parts.
Recomendado
Automotive Body Electronics Module
In automotive body controllers (BCM), door modules, and HVAC interfaces, the 5M80ZT100A5N serves as the deterministic-logic backbone that decodes CAN/LIN bus wake events, drives relay and LED matrices, and implements safety state machines. The AEC-Q100 qualification and 1.8 V core with 3.3 V I/O tolerance let it interface directly with automotive MCUs and 12 V load-driver ICs. Its non-volatile flash-based configuration means the device comes up in <1 ms after battery reconnect, critical for crash-event data logging and immediate response to ignition-on.
Recomendado
Consumer Electronics Interface Bridge
The 5M80ZT100A5N bridges modern low-voltage application processors to legacy peripherals in set-top boxes, smart-home hubs, and home appliances - translating 1.8 V I2C/SPI bus signals to 3.3 V UART or GPIO lines without software overhead. Its 80 user I/Os in a 100-TQFP package give designers ample headroom for keypad scanning, LED multiplexing, and rotary-encoder decoding. The integrated 8-Kbit User Flash Memory (UFM) stores boot configuration, calibration constants, and product serial numbers, eliminating an external EEPROM.
Recomendado
Motor Driver Interface Decoder
Between a microcontroller and a multi-axis stepper or BLDC driver, the 5M80ZT100A5N implements direction logic, PWM distribution, fault-mux decoding, and home-switch conditioning in a single package. Its 7.5 ns tPD keeps the PWM-to-driver propagation well below typical 20 kHz PWM periods, ensuring phase-timing fidelity. The multi-voltage VCCIO banks let one CPLD talk to a 1.8 V MCU on one side and 3.3 V gate drivers on the other, eliminating a level-shifter IC and reducing BOM cost on CNC, 3D-printer, and robotics control boards.
Recomendado
Communications Equipment Glue Logic
In networking line cards, small-cell base stations, and industrial Ethernet switches, the 5M80ZT100A5N performs address decoding, FIFO flag combination, LED-status multiplexing, and clock-domain crossing between PHY, switch ASIC, and management CPU. Its 118.3 MHz fMAX on global clocks handles 100 Mbps Ethernet MDIO bus timing without metastability issues, and its non-volatile configuration ensures immediate post-boot readiness without an external configuration PROM. The 100-TQFP footprint exposes 80 user I/Os, sufficient for typical 24-port switch front-panel indicator designs.
Recomendado
Test and Measurement Front-End Logic
Bench-top oscilloscopes, data loggers, and lab instrumentation use the 5M80ZT100A5N to implement front-panel button de-bouncing, rotary-encoder quadrature decoding, range-relay selection, and trigger-arm logic. Its deterministic 7.5 ns tPD ensures trigger-arming latencies stay below the instrument's specified trigger jitter budget. The User Flash Memory block stores calibration coefficients and serial numbers, while JTAG (IEEE 1149.1) enables in-system firmware updates in the field without removing the instrument from service.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para 5M80ZT100A5N — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | 5M80ZT100I5N | 5M80ZT100C5N | 5M160ZT100A5N | 5M240ZT100A5N | 5M570ZT100A5N |
|---|---|---|---|---|---|---|
| Package | TQFP-100 | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same |
| Brand | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) |
| Macro Cells | 64 | 64 | 64 | 160 | 240 | 570 |
| Pin-to-Pin Delay (tPD) | 7.5 ns | 7.5 ns | 7.5 ns | 7.5 ns | 7.5 ns | 7.5 ns |
| Temperature Grade | -40 C to +125 C (AEC-Q100) | -40 C to +100 C (Industrial) | 0 C to +85 C (Commercial) | -40 C to +125 C (AEC-Q100) | -40 C to +125 C (AEC-Q100) | -40 C to +125 C (AEC-Q100) |
| Core Voltage (VCCINT) | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| User I/O Count | 80 | 80 | 80 | 80 | 80 | 80 |
| Configuration Memory | Flash, non-volatile | Flash, non-volatile | Flash, non-volatile | Flash, non-volatile | Flash, non-volatile | Flash, non-volatile |
| Programming Interface | JTAG (IEEE 1149.1) | JTAG (IEEE 1149.1) | JTAG (IEEE 1149.1) | JTAG (IEEE 1149.1) | JTAG (IEEE 1149.1) | JTAG (IEEE 1149.1) |
| Approx. Unit Price @ 1 pc | $2.95 | $2.50 - $2.80 | $2.20 - $2.50 | $5.50 - $7.00 | $8.00 - $10.00 | $14.00 - $18.00 |
Principais diferenciais
- Non-volatile flash-based configuration (vs Xilinx XC2C32A (CoolRunner-II, SRAM-less but different architecture))
- Multi-voltage I/O bank support (vs 5M80ZE64A5N (same 64 macrocells, 64-EQFP package))
- Automotive-grade qualification with same density (vs 5M80ZT100C5N (commercial grade, same TQFP-100 footprint))
Notas de projeto
The 5M80ZT100A5N requires two distinct supply rails: VCCINT at 1.8 V for the core logic and VCCIO per bank (1.2/1.5/1.8/2.5/3.3 V) for the I/O drivers. Place a 0.1 uF X7R ceramic decoupling capacitor within 3 mm of every VCCINT and VCCIO pin, plus one bulk 10 uF tantalum or ceramic capacitor near the device. Without proper decoupling, simultaneous-switching outputs can inject noise into the JTAG chain and cause JTAG IDCODE readback failures during in-system programming.
Although MAX V CPLDs are CMOS-low-power (typical Icc <50 mA at 1.8 V), the 100-TQFP package has a junction-to-ambient thermal resistance (theta_JA) of approximately 40-50 C/W on a 4-layer JEDEC test board with 2 oz copper. Estimated: at full I/O toggle rate across 80 outputs with 10 pF loads and 25 MHz, junction rise above ambient is under 10 C. No heatsink is required, but for enclosed industrial cabinets operating above 70 C ambient, derate switching frequency or reduce simultaneously-switching I/O count.
Route JTAG signals (TCK, TMS, TDI, TDO) as a daisy-chain with 4.7 kohm pull-ups on TMS and TDI to VCCIO of the JTAG bank, per Altera JTAG configuration guidelines. Keep TCK trace length under 100 mm to avoid signal-integrity issues at high TCK frequencies. The 100-TQFP land pattern has 0.5 mm pitch - use ENIG surface finish and a reflow profile compliant with JEDEC J-STD-020 MSL-3 handling requirements.
Common design pitfalls: (1) Forgetting to set unused I/O pins to 'tri-stated input with weak pull-up' in Quartus, which can leave inputs floating and cause additional supply current; (2) mixing 1.8 V and 3.3 V peripherals in the same I/O bank - VCCIO is per-bank but only one voltage per bank; (3) assuming the part is in-system programmable without JTAG header access - always bring out the 4 JTAG pins plus GND to a test-point footprint for field reprogrammability.
Informações de conformidade
AEC-Q100 automotive qualification per the 'A' suffix in 5M80ZT100A5N. RoHS compliant and lead-free per Altera/Intel product declaration. Halogen-free per JEDEC JS709B PCB-material standard. Supply-chain conflict-minerals compliance per Section 1502 of the Dodd-Frank Act.