AD7482BST - 12-Bit 3 MSPS SAR ADC | Analog Devices
N.º da peça: AD7482BST ✓ AtivoAD7482BST Visão geral
A successive-approximation ADC, or SAR ADC, converts an analog voltage by comparing it with a reference through a series of successive bit decisions. The AD7482 belongs to the ADC hierarchy, which includes data converters, analog-to-digital converters, and signal-chain semiconductors. Its parallel interface supports direct connection to digital control logic rather than relying on a serial protocol.
The principal feature is a conversion throughput of up to 3 MSPS with 12-bit resolution. Analog Devices describes the device as low power and high speed, with a low-noise, wide-bandwidth track-and-hold circuit that can handle input frequencies above 40 MHz. These characteristics support sampled measurement, instrumentation, communications, industrial control, and embedded signal-processing applications.
The internal architecture uses the AD7482 SAR conversion core and an on-chip sample-and-hold function. The wide input bandwidth allows the sampling network to acquire high-frequency signals, while the 12-bit output defines the numerical resolution available to downstream logic. Because the interface is parallel, the converter can require more board routing than a serial ADC, but it reduces the need to multiplex or deserialize data before capture.
Typical uses include industrial measurement systems, waveform capture, communications equipment, control loops, and data-acquisition front ends. The AD7482BST is especially appropriate when throughput and input bandwidth matter more than a serial bus or exceptionally small package size. A suitable design must also account for reference accuracy, source impedance, acquisition time, digital timing, and analog trace integrity.
For PCB implementation, place the analog input, reference, and decoupling connections close to the device, keep digital return currents away from sensitive analog nodes, and provide a quiet reference source. Confirm setup and conversion timing against the manufacturer datasheet before using the parallel outputs as system data-valid and state signals.
This product page combines the manufacturer’s AD7482 specifications, practical acquisition guidance, verified family alternatives, and sourcing information for engineers designing around the 48-lead LQFP footprint. It is intended to accelerate component selection while keeping critical design assumptions visible.
Alternativas drop-in para AD7482BST — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com AD7482BST (mesmo formato e footprint) — diferindo em Package.
AD7482ASTZ
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
AD7482BSTZ
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
AD7482BST Classificações máximas e características elétricas
| Resolução | 12 bit |
| Conversion Type | Successive approximation register (SAR) |
| Maximum Throughput Rate | 3 MSPS |
| Analog Input Bandwidth | Above 40 MHz |
| Tipo de interface | Parallel |
| Analog Input Channels | 1 channel |
| Track-and-Hold Circuit | On-chip, low-noise, wide-bandwidth |
| Encapsulamento | 48-lead LQFP |
| Package Body Size | 7 mm x 7 mm |
| Tipo de montagem | Surface mount |
Guia de Configuração de Pinos do AD7482BST 7 mm x 7 mm
Configuração de pinos para AD7482BST (pacote 7 mm x 7 mm). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.
Nenhum dado detalhado de pinagem disponível para AD7482BST.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
AD7482BST é adequado para 6 aplicaçãos: Industrial Process Measurement, Communications Signal Capture, Waveform Data Acquisition, Precision Control Loops, Test and Measurement Equipment, Embedded Sensor Acquisition.
Industrial Process Measurement
The AD7482BST fits industrial process-monitoring front ends that need faster sampling than a slow general-purpose ADC. Its 12-bit resolution and throughput of up to 3 MSPS permit dense waveform capture, while the analog input bandwidth above 40 MHz provides acquisition capability beyond the converter’s base sample rate. Use a low-drift reference, a suitable input amplifier, and close placement of bypass capacitors to preserve 12-bit measurement quality. The parallel interface can feed a controller or capture logic directly, although its 48-lead footprint requires careful planning. Where process signals change rapidly, verify acquisition time and settling against the source impedance rather than relying on bandwidth alone.
Recomendado
Communications Signal Capture
The AD7482BST is appropriate for communications equipment that samples intermediate-frequency or other analog waveforms before digital processing. Its 3 MSPS maximum throughput supports discrete-time conversion, and the track-and-hold circuit can handle input frequencies above 40 MHz. This bandwidth is particularly useful when several times the signal frequency must be sampled. The 12-bit parallel output exposes the converted word directly to FPGA or logic devices, while the wide LQFP package requires a deliberate fanout strategy. Designers should control clock and digital-edge crosstalk, maintain a quiet reference, and confirm that the input network settles within the specified acquisition interval.
Recomendado
Waveform Data Acquisition
For waveform data-acquisition systems, the AD7482BST combines 12-bit resolution with a maximum 3 MSPS throughput rate, allowing repeated samples of changing analog signals to be captured by parallel logic. Its on-chip track-and-hold circuit and input bandwidth above 40 MHz support broader signal content than the sample rate alone would imply. The design should include an input range that matches the ADC, anti-alias filtering appropriate to the selected rate, and a reference with low enough noise for the intended resolution. A capture controller must also handle the parallel data-valid and state timing shown in the manufacturer datasheet.
Recomendado
Precision Control Loops
The AD7482BST can serve as the sensing element in a sampled control system requiring regular analog measurements and rapid control updates. A 3 MSPS conversion rate permits one or more feedback measurements during each control interval, while the 12-bit word supplies sufficient resolution for many position, level, and feedback tasks. The parallel interface allows direct connection to digital control logic, but loop design must account for conversion latency and the acquisition network’s settling behavior. Stable references and low-noise grounding are essential because supply and reference variation propagate directly into the control measurement.
Recomendado
Test and Measurement Equipment
The AD7482BST is suitable for compact test and measurement instruments that need high-speed sampled readings without a complex serial conversion interface. The 12-bit resolution provides a practical balance between measurement detail and conversion speed, while throughput up to 3 MSPS supports time-domain inspection. The wide-bandwidth track-and-hold circuit can capture higher-frequency content when the test point permits it. Instrument designers should calibrate gain and offset, use a low-noise reference, and separate analog input routing from the 12-bit parallel bus. Input conditioning must also provide the correct range and source impedance for reliable conversion results.
Recomendado
Embedded Sensor Acquisition
The AD7482BST can be used in embedded acquisition systems for rapidly changing sensor outputs when the application requires more than a low-rate multiplexed converter. Its 3 MSPS capability captures successive sensor values for filtering, thresholding, or event analysis, and the 12-bit parallel output allows efficient transfer into embedded digital logic. The input bandwidth above 40 MHz is not normally required for slow sensors, but it provides flexibility when the same board also handles higher-frequency conditioning stages. Keep sensor excitation and converter routing separated, use local bypass capacitors, and verify settling at the programmed sampling rate to maintain consistent results.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para AD7482BST — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | AD7482ASTZ | AD7482BSTZ |
|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Package | 48-lead LQFP | 48-lead LQFP | 48-lead LQFP |
| Resolution | 12 bit | 12 bit | 12 bit |
| Conversion Type | Successive approximation register (SAR) | Successive approximation register (SAR) | Successive approximation register (SAR) |
| Maximum Throughput Rate | 3 MSPS | 3 MSPS | 3 MSPS |
| Analog Input Bandwidth | Above 40 MHz | Above 40 MHz | Above 40 MHz |
| Interface | Parallel | Parallel | Parallel |
| Analog Input Channels | 1 channel | 1 channel | 1 channel |
| Track-and-Hold Circuit | On-chip, low-noise, wide-bandwidth | On-chip, low-noise, wide-bandwidth | On-chip, low-noise, wide-bandwidth |
Principais diferenciais
- High-speed wide-bandwidth sampling in a 12-bit SAR converter (vs AD7482ASTZ)
- Direct parallel data capture (vs AD7482BSTZ)
- On-chip wide-bandwidth track-and-hold circuit (vs AD7482ASTZ)
Notas de projeto
Route the analog input and reference connections as short, quiet traces and place their bypass capacitors close to the corresponding device pins. The AD7482 uses a parallel output bus, so clock and data-return currents can couple into the sampling node if the analog and digital paths share board area. Keep the converter and its input network away from switching inductors and high-current return paths, and use the pin-description table in the manufacturer datasheet to distinguish analog, reference, supply, and digital connections.
Do not assume that the 3 MSPS conversion rate guarantees valid results for every source impedance. The sample-and-hold capacitor must recharge and settle during each acquisition interval, and the input amplifier or sensor must have sufficiently low output impedance at the relevant frequency. Use the Analog Devices acquisition-time and input-capacitance guidance to select the driving network, and validate settling with the intended full-scale input rather than a small test signal.
Treat the 12-bit parallel outputs as a simultaneous high-speed bus even though the maximum conversion rate is 3 MSPS. Match output timing to the receiving logic, keep the bus traces short, and use a deliberate return path beneath or beside the data routing. Avoid unnecessary vias, place digital termination according to the system architecture, and separate clock routing from sensitive reference and analog-input nodes. Grounding and return-current decisions can materially affect the noise and timing margin of the capture system.
Provide local, low-inductance bypass connections at the device supply pins and use a reference source with noise and impedance appropriate for a 12-bit converter. Reference error can appear directly as gain and offset error, while reference noise contributes to the converter’s noise floor. Confirm capacitor voltage ratings, stability requirements, and the recommended reference network in the manufacturer application circuit rather than substituting a generic capacitor or reference arrangement without checking load behavior.
Informações de conformidade
Compliance declarations must be confirmed from the manufacturer’s current product documentation or declaration for the exact ordering code.