AD8008ARM - 380 MHz Dual Current-Feedback Amplifier | Analog Devices
N.º da peça: AD8008ARM ✓ AtivoAD8008ARM Visão geral
A current-feedback amplifier is a voltage-feedback amplifier family that uses a low-impedance inverting input to control the amplifier. Current feedback amplifiers are widely used in high-speed instrumentation, active filters, video and test equipment because they can maintain high bandwidth and low distortion over a broad gain range. In the electronics hierarchy, the AD8008ARM is an analog amplifier IC, an operational amplifier, and a current-feedback amplifier.
The AD8008 includes two amplifier channels in one package, reducing board area while simplifying dual-channel signal paths. Its 380 MHz gain-bandwidth product supports signal paths that require substantially more bandwidth than general-purpose operational amplifiers. The low 4 uA supply current also distinguishes it from many high-speed amplifiers that consume considerably more power.
Analog Devices describes the AD8007 and AD8008 as high-performance current-feedback amplifiers using its proprietary second-generation eXtra-Fast Complementary Bipolar, or XFCB, process. The AD8008ARM therefore combines bipolar transistor signal paths with a dual-channel architecture. The 59 dB instrumentation-amplifier specification is useful when determining the attainable accuracy of closed-loop gain and system bandwidth, while the 380 MHz characteristic identifies the amplifier as a high-speed device rather than a precision DC amplifier.
Typical uses include active filters, pulse-shaping networks, video signal conditioning, communications equipment, instrumentation, and test-and-measurement systems. The dual-channel configuration is particularly useful when two signals must be amplified consistently, such as in differential interfaces, matched filter stages, or paired instrumentation channels. Its low supply current can also support portable test equipment where power consumption is important.
PCB design should preserve the high-speed behavior of the device. Keep feedback components and signal traces short, use a continuous ground reference, and provide local supply bypassing close to the power pins. Because a current-feedback amplifier does not use the same gain-bandwidth relationship as a conventional voltage-feedback amplifier, determine the required feedback resistor directly from the manufacturer’s gain and bandwidth guidance.
This product page combines manufacturer specifications with practical selection guidance, package information, and drop-in comparison data for engineers evaluating the AD8008ARM in high-speed analog signal chains.
Alternativas drop-in para AD8008ARM — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
AD8022ARM-REEL
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
AD8008ARM Classificações máximas e características elétricas
| Amplifier Type | Dual current-feedback amplifier |
| Number of Channels | 2 channels |
| Gain-Bandwidth Product | 380 MHz |
| Instrumentation Amplifier Gain | 59 dB |
| Corrente de alimentação | 4 uA |
| Minimum Supply Voltage | 5 V |
| Maximum Supply Voltage | 12 V |
| Supply Voltage Span | 5 V to 12 V |
| Faixa de temperatura de operação | -40 C to +85 C |
| Encapsulamento | 8-MSOP, 3.00 mm width |
| Número de pinos | 8 pins |
| Tipo de montagem | Surface mount |
| Process Technology | Second-generation XFCB complementary bipolar |
Guia de Configuração de Pinos do AD8008ARM 8-msop, 3.00 mm width
Configuração de pinos para AD8008ARM (pacote 8-msop, 3.00 mm width). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.
Nenhum dado detalhado de pinagem disponível para AD8008ARM.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
AD8008ARM é adequado para 6 aplicaçãos: Active Filter Networks, Video Signal Conditioning, Instrumentation Signal Conditioning, Pulse and Waveform Shaping, Portable Test Equipment, Communications Interface.
Active Filter Networks
The AD8008ARM fits active filter stages requiring substantially more bandwidth than a general-purpose dual operational amplifier. Its 380 MHz gain-bandwidth product and current-feedback architecture are suited to low-pass, high-pass, and band-pass networks that process fast signals while maintaining low distortion. Two amplifier channels can implement a matched second-order section or two coordinated filter stages without using separate packages. The 4 uA supply current also benefits compact filter modules and battery-powered analyzers. When calculating component values, follow the current-feedback gain and bandwidth guidance in the manufacturer datasheet rather than applying the voltage-feedback gain-bandwidth relationship. Short feedback traces and closely placed bypassing capacitors are important for preserving predictable high-frequency behavior.
Recomendado
Video Signal Conditioning
AD8008ARM is appropriate for video buffering, impedance conversion, and signal-shaping paths where the 380 MHz gain-bandwidth product provides more bandwidth than conventional dual op amps. The current-feedback topology is particularly useful in video circuits because it supports high-speed closed-loop operation with controlled feedback components. Its dual-channel construction can process luminance and chrominance, or complementary data paths, while conserving board area. The specified 5 V to 12 V supply range permits operation from a single 5 V rail or from split supplies, provided the input and output signal levels remain within the common-mode limits. Use a solid ground plane and short output routing to minimize added distortion and maintain video quality.
Recomendado
Instrumentation Signal Conditioning
The AD8008ARM can condition high-bandwidth sensor and instrumentation signals when a dual, low-power current-feedback amplifier is preferred over a general-purpose op amp. Its 59 dB instrumentation-amplifier performance and 380 MHz gain-bandwidth product support closed-loop stages operating well above audio frequencies. The two channels can handle a differential signal or matched inputs while keeping package count low. For sensor interfaces, verify input bias current, common-mode range, and output swing against the actual source impedance and excitation level before finalizing the design. The 4 uA supply current is useful for compact field instruments, while the 8-MSOP package supports placement near the sensor connector to reduce susceptibility to noise and interference.
Recomendado
Pulse and Waveform Shaping
AD8008ARM suits pulse amplification, slew control, and waveform-shaping circuits that benefit from its 380 MHz gain-bandwidth product. Current-feedback amplifiers are widely chosen for high-speed pulse circuits because their bandwidth can remain useful over multiple closed-loop gains, subject to the manufacturer’s feedback-resistor guidance. The dual-channel arrangement allows a signal to be amplified and conditioned along two paths with identical device characteristics. The low 4 uA supply current can reduce system power in portable pulse-analysis equipment. Keep the feedback loop compact, avoid long stubs, and place supply capacitors near the device. Because edge-rate and distortion performance depend on output loading and feedback values, prototype the final timing and loading conditions.
Recomendado
Portable Test Equipment
The AD8008ARM is a practical choice for portable oscilloscope, waveform-generator, and signal-analysis equipment that needs high bandwidth without a large power budget. Its 380 MHz gain-bandwidth product supports acquisition and drive paths above many general-purpose amplifier limits, while the 4 uA supply current limits quiescent consumption. Two channels can share the same package in a dual-trace instrument or implement a differential input stage. The 8-MSOP footprint reduces board area, although careful layout remains necessary to prevent added distortion. Keep sensitive inputs away from power converters and digital return currents, and use the manufacturer’s application guidance to select feedback resistors that maintain the required bandwidth and pulse response.
Recomendado
Communications Interface
AD8008ARM can serve in high-speed communications interface and line-driver stages requiring low distortion and wide bandwidth. Its 380 MHz gain-bandwidth product provides useful margin for digital transitions, while the current-feedback architecture allows gain selection through the external feedback network. The two channels can handle transmit and receive paths or a pair of differential legs in a compact implementation. The 5 V to 12 V operating span is compatible with common low-voltage interface rails, subject to the device’s input and output swing restrictions. Maintain a continuous return path, keep feedback components close to the amplifier pins, and separate noisy switching-current paths from the signal reference to limit channel-to-channel crosstalk.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para AD8008ARM — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | AD8022ARM-REEL |
|---|---|---|
| Brand | Analog Devices | Analog Devices |
| Package | 8-MSOP | 8-MSOP - same package |
| Amplifier Configuration | Dual current-feedback amplifier | Dual current-feedback amplifier |
| Minimum Supply Voltage | 5 V | 4.5 V |
| Maximum Supply Voltage | 12 V | 26 V |
| Operating Temperature Range | -40 C to +85 C | -40 C to +85 C |
| Mounting Type | Surface mount | Surface mount |
Principais diferenciais
- Combines two high-speed channels with low quiescent current (vs AD8022ARM-REEL)
- Defined low-voltage operating range (vs AD8022ARM-REEL)
- Specified instrumentation-amplifier performance (vs AD8022ARM-REEL)
- Compact dual-channel implementation (vs AD8022ARM-REEL)
Notas de projeto
Place the feedback network directly beside the amplifier pins and keep its loop physically small. Long feedback traces can add parasitic inductance and capacitance, which can alter high-speed stability and pulse response. Route the signal and return paths over a continuous ground plane, avoid routing beneath the MSOP where practical, and place the input stage away from switching nodes and inductors.
Place the supply bypass capacitor close to the device power pin and connect it through a short ground path. Use the decoupling arrangement and capacitor values recommended in the Analog Devices application guidance for the intended bandwidth. Decoupling requirements become more important as the 380 MHz gain-bandwidth product is approached, because supply impedance can otherwise influence high-frequency distortion and oscillation margin.
Do not calculate closed-loop bandwidth using the voltage-feedback gain-bandwidth relationship. The AD8008 is a current-feedback amplifier, so the selected feedback resistor influences gain, bandwidth, and stability. Use the manufacturer’s gain-versus-bandwidth guidance, confirm output-current capability for the intended load, and verify input and output common-mode limits before committing the circuit to layout.
The 4 uA supply current makes average quiescent dissipation low, but actual channel dissipation rises with output current, supply voltage, and output swing. Check the amplifier’s output-current limit against capacitive and resistive loads and provide copper around the MSOP when operating near maximum swing. Account for temperature rise at the device rather than relying only on ambient temperature, especially in enclosed portable equipment.
Informações de conformidade
No RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration for the exact AD8008ARM ordering code was identified. AEC-Q100 is not applicable to this linear amplifier.