AD977CRS - 16-Bit 100 kSPS Serial ADC | Analog Devices
N.º da peça: AD977CRS ✓ AtivoAD977CRS Visão geral
An ADC converts an analog input voltage into a numeric code that digital hardware can process, store, transmit, or analyze. The AD977CRS belongs to the successive-approximation, or SAR, ADC family within the broader data-converter and signal-processing hierarchy. SAR ADCs compare the unknown input against an internal reference through a series of conversion steps, making them practical for precision measurements where resolution, throughput, power consumption, and circuit complexity must be balanced.
The AD977CRS combines a 16-bit conversion resolution with a 100 kSPS throughput rate. It supports single 5 V operation, which can simplify analog and digital supply planning in compact systems. Maximum power dissipation is 100 mW, and the device includes a power-down mode. Factory calibration, comprehensive DC and AC testing, and specified SNR and THD performance support repeatable acquisition results.
Internally, the AD977 uses a factory-calibrated switched-capacitor architecture. Its serial interface reduces the number of data connections required compared with a parallel ADC, allowing a smaller package and more compact PCB layout. The AD977 family also offers an external-reference selection and multiple input-range options, but exact values for the AD977CRS configuration should be confirmed against the manufacturer datasheet before finalizing analog front-end design.
Typical uses include industrial process measurement, instrumentation, laboratory data acquisition, vibration monitoring, and embedded sensor conditioning. The 100 kSPS rate supports continuous acquisition of moderately fast analog waveforms, while the 16-bit code width provides 65,536 nominal digital levels. Serial output is especially useful where connector count and board area are more restrictive than maximum bus throughput.
Design the reference and input network carefully because ADC accuracy depends on source impedance, reference stability, capacitor selection, grounding, and control of digital return currents. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks. Confirm the selected input range, reference arrangement, sampling dynamics, and acquisition timing against the AD977 datasheet before production release.
This page organizes the AD977CRS specifications, sourcing information, application guidance, comparison fields, and design checks needed to evaluate the converter for a new measurement system.
Alternativas drop-in para AD977CRS — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com AD977CRS (mesmo formato e footprint) — diferindo em Package, Supply Voltage, Architecture, Converter Type, Number of Input Channels.
Nenhuma alternativa drop-in disponível para este produto.
Solicitar alternativasAD977CRS Classificações máximas e características elétricas
| Converter Type | 16-bit successive-approximation ADC |
| Resolução | 16 bit |
| Throughput Rate | 100 kSPS |
| Number of Inputs | 1 input |
| Architecture | Factory-calibrated switched-capacitor SAR |
| Output Interface | Serial |
| Tensão de alimentação | 5 V |
| Power Supply Type | Single supply |
| Maximum Power Dissipation | 100 mW |
| Power-Down Mode | Yes |
| Encapsulamento | 28-pin SSOP |
| Tipo de montagem | Surface mount |
Guia de Configuração de Pinos do AD977CRS 28-pin ssop
Configuração de pinos para AD977CRS (pacote 28-pin ssop). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.
Nenhum dado detalhado de pinagem disponível para AD977CRS.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
AD977CRS é adequado para 6 aplicaçãos: Industrial Process Measurement, Laboratory Data Acquisition, Vibration and Condition Monitoring, Embedded Sensor Interfaces, Audio and Communications Measurement, Power and Drive System Diagnostics.
Industrial Process Measurement
The AD977CRS suits process-monitoring systems that acquire sensor signals at up to 100 kSPS while retaining 16-bit numerical resolution. Its 16-bit code width provides 65,536 nominal levels, while the serial output limits the number of interconnects required between the converter and a controller. The single 5 V supply and 100 mW maximum power dissipation simplify embedded acquisition hardware. The analog front end should convert the sensor output into the selected AD977 input range, provide suitable source impedance, and use filtering matched to the process bandwidth. Firmware should verify that the sample rate does not exceed 100 kSPS.
Laboratory Data Acquisition
The AD977CRS can serve as the conversion stage in a laboratory instrument that combines analog conditioning with digital capture. Its 100 kSPS throughput supports continuously sampled waveforms whose useful bandwidth is compatible with that rate, while 16-bit resolution improves the distinction between closely spaced measurements. The serial interface helps reduce board width in bench-oriented equipment, and the single 5 V supply simplifies rail planning. For laboratory accuracy, use a low-noise reference, shielded analog routing, calibrated input attenuation, and software correction for the gain, offset, and linearity characteristics specified by the manufacturer.
Vibration and Condition Monitoring
The AD977CRS is appropriate for vibration, acoustic, and condition-monitoring systems that need synchronized acquisition from multiple conditioned sensor channels. The 100 kSPS limit supports a broad range of low- and mid-frequency monitoring tasks when paired with suitable anti-alias filtering. Its 16-bit resolution captures small amplitude variations, and its factory-calibrated switched-capacitor architecture supports repeatable conversion performance. Use an anti-alias filter whose cutoff and phase behavior meet the analysis bandwidth, then keep sensor returns, reference routing, and digital clock lines separated to reduce correlated noise in the captured data.
Embedded Sensor Interfaces
The AD977CRS can digitize analog outputs from pressure, temperature, flow, or position sensors in compact embedded equipment. A 100 kSPS rate is more than adequate for many slowly varying process variables and permits the same converter to capture transient events generated by the conditioned sensor signal. The 16-bit resolution supports fine-grained measurement, while serial output reduces wiring compared with a parallel ADC. Configure the input stage for the intended unipolar or bipolar range, observe acquisition-time requirements, and confirm whether an internal or external reference best matches the accuracy and power budget of the system.
Audio and Communications Measurement
The AD977CRS can be applied to communications and audio test equipment when the measured bandwidth is compatible with a 100 kSPS conversion rate. Its 16-bit resolution is appropriate for capturing signal levels with finer granularity than an 8-bit converter, while the serial interface supports integration with digital processing hardware. The converter's stated SNR and THD characteristics must be checked against the required measurement bandwidth and input level. Use an appropriate anti-alias filter, a stable reference, controlled input attenuation, and careful grounding so that converter performance is not obscured by the analog front end.
Power and Drive System Diagnostics
The AD977CRS is suitable for diagnostic systems that monitor control signals, actuator feedback, or power-converter status. A 100 kSPS rate captures control-loop events with useful temporal resolution, and 16-bit output retains detail in measurements where operating quantities change over a limited range. The single 5 V supply and 100 mW maximum dissipation simplify integration near powered equipment. Keep high-current switching paths physically separated from the ADC input and reference nodes, use common-mode control appropriate to the selected input range, and place filtering close to the converter to prevent switching transients from reaching the sampled signal.
Dados de referência de engenharia para AD977CRS — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto |
|---|---|
| Brand | Analog Devices |
| Package | 28-pin SSOP |
| Resolution | 16 bit |
| Throughput Rate | 100 kSPS |
| Number of Inputs | 1 input |
| Output Interface | Serial |
| Supply Voltage | 5 V |
| Maximum Power Dissipation | 100 mW |
| Architecture | Factory-calibrated switched-capacitor SAR |
Principais diferenciais
- 100 kSPS throughput in a 16-bit converter (vs AD977ABRS)
- Single 5 V supply operation (vs AD977ABRS)
- Factory-calibrated switched-capacitor SAR architecture (vs AD977ABRS)
Notas de projeto
Place the required bypass and filtering capacitors close to the AD977CRS supply, reference, and analog-input pins. Keep the analog input path short, use a continuous ground reference beneath the analog section, and route serial clock and data outputs away from sensitive input traces. The exact component values and topology must follow the AD977 manufacturer datasheet for the selected input range and reference configuration.
Treat the serial interface as a timing-sensitive digital subsystem. Use controlled-impedance routing where appropriate, provide a clean clock reference, and observe the converter's acquisition and conversion timing before selecting the digital controller's read rate. Avoid adding unnecessary long stubs between the AD977CRS and the receiving logic because they can degrade signal integrity at the interface's upper operating frequency.
Do not confuse the 100 kSPS AD977CRS with the 200 kSPS AD977A configuration. Confirm the exact ordering code, input range, reference arrangement, temperature rating, and 28-pin SSOP pin mapping during design review. Use the manufacturer pin-description table rather than inferring connections from another member of the AD977 family, particularly when the design depends on the AD977A or AD977ABRS.
Informações de conformidade
Compliance attributes were not stated in the available product information and require confirmation from Analog Devices or the manufacturer datasheet.