ADM232LJRZ - 2/2 RS-232 Transceiver, 5V, 120kbps | Analog Devices
N.º da peça: ADM232LJRZ ✓ AtivoADM232LJRZ Visão geral
An RS-232 transceiver is an interface IC that combines line drivers and line receivers with the electrical conversion required by EIA-232 links. It belongs to the RS-232 interface IC hierarchy, where a dual driver converts logic-level transmit signals into bipolar RS-232 levels and two receivers convert incoming bipolar signals back into CMOS-compatible logic. This device is intended for systems where ±12 V is unavailable, using its on-board dc-to-dc converters to generate the required positive and negative voltage swings.
Key characteristics include two transmitters, two receivers, a single 5 V supply, operation over a 4.5 V to 5.5 V input range, and a data rate of up to 120 kbps. The on-board converters produce approximately ±9 V output swing, while the charge-pump network uses small 1 µF capacitors. The interface is designed to meet EIA-232-E and V.28 requirements, making it appropriate for point-to-point serial links, instrumentation, data acquisition, and control systems.
The ADM232L family combines CMOS power-efficient logic with bipolar RS-232 signal levels. Its integrated dc-to-dc converter avoids a separate negative supply and allows the interface to operate from one 5 V rail. Because the transmitter outputs are not TTL-compatible, downstream circuitry must use the transceiver's RS-232 output levels directly rather than driving the outputs from ordinary 5 V logic without proper translation.
Typical applications include serial adapters, industrial control links, test and measurement equipment, embedded instrumentation, and communication ports that require two transmit and two receive channels. In a typical implementation, the device connects logic-level UART pins to an external DB9 or other RS-232 connector, while protection components handle electrostatic-discharge and cable-transient risks.
When laying out the PCB, place the charge-pump capacitors and interface-side protection components close to the device. Keep RS-232 driver traces away from sensitive analog inputs, and provide a solid ground reference between the transceiver and connected equipment. Confirm connector-level fault protection and cable length against the system communication requirements.
Alternativas drop-in para ADM232LJRZ — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com ADM232LJRZ (mesmo formato e footprint) — diferindo em Package, Data Rate, Function, Maximum Data Rate, Operating Temperature Range.
MAX3232CSE+
✅ Drop-InConsulte o preço
Ver ficha técnica →MAX3241CSE
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
MAX232CSE+T
✅ Drop-InConsulte o preço
Ver ficha técnica →MAX232ACSE+T
✅ Drop-InConsulte o preço
Ver ficha técnica →MAX3232EESE
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ADM232LJRZ Especificações
| Transceiver Configuration | 2 drivers / 2 receivers |
| Tipo de interface | Full-duplex RS-232 |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Nominal Supply Voltage | 5 V |
| Maximum Data Rate | 120 kbps |
| Transmitter Output Swing | ±9 V from a 5 V supply |
| Charge-Pump Capacitor Value | 1 µF |
| Protocol Compliance | EIA-232-E and V.28 |
| Encapsulamento | 16-pin SOIC, 7.50 mm width |
| Tipo de montagem | Surface mount |
| Shipping Packaging | Tube |
| On-Board DC-to-DC Converter | Yes |
| Logic Compatibility | CMOS |
Guia de Configuração de Pinos do ADM232LJRZ 16-pin soic, 7.50 mm width
Configuração de pinos para ADM232LJRZ (pacote 16-pin soic, 7.50 mm width). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para ADM232LJRZ.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
ADM232LJRZ é adequado para 6 aplicaçãos: Industrial Serial Control, Test and Measurement Equipment, Data Acquisition Modules, Embedded Serial Port Expansion, Network Equipment Service Ports, Instrumentation and Portable Analyzers.
Industrial Serial Control
The ADM232LJRZ fits industrial control equipment that requires two RS-232 transmit channels and two receive channels from one 5 V rail. Its 120 kbps maximum data rate is suitable for supervisory protocols, configuration links, and service interfaces. The integrated dc-to-dc converter supplies approximately ±9 V signal swing without a separate negative supply, reducing connector-side power complexity. Place the 1 µF charge-pump capacitors close to the device and route the RS-232 outputs directly toward protected connector circuitry. Industrial suitability should still be confirmed against the required ambient temperature, EMC level, isolation arrangement, and enclosure grounding strategy.
Recomendado
Test and Measurement Equipment
Instrumentation systems often need a compact, reliable path between a control processor and external RS-232 equipment. The ADM232LJRZ provides a 2/2 full-duplex interface, 4.5 V to 5.5 V supply operation, and throughput up to 120 kbps, which suits command and measurement-data links. Its integrated charge pump removes the need for a separate negative rail at the interface. When connecting to test equipment, use a defined ground reference and place transient protection near the external connector. Verify the protocol's baud rate, line length, connector gender, and command response timing before finalizing the system interface.
Recomendado
Data Acquisition Modules
The ADM232LJRZ can connect a data-acquisition controller to legacy RS-232 instruments and service ports. Two drivers and two receivers allow command traffic and returned measurements to coexist in a full-duplex arrangement, while the 120 kbps rate is appropriate for many sensor, laboratory, and process-control protocols. The single 5 V supply simplifies isolated or multi-rail system designs, and the integrated converter provides approximately ±9 V output levels. Keep sensitive analog measurement sections physically separate from the transceiver and converter area, and verify grounding carefully to prevent ground potential differences from disturbing low-level measurements.
Recomendado
Embedded Serial Port Expansion
An embedded controller with limited UART channels can use the ADM232LJRZ to add two bidirectional RS-232 ports. The device's 2/2 topology and 120 kbps maximum data rate suit command consoles, remote controls, and equipment-management links. Because the transmitter produces RS-232 levels rather than CMOS logic directly, connect the driver outputs to the external line and route receiver outputs back to the host UART or level-shifting logic. Confirm the controller's signal voltage and use the manufacturer pin table to verify every connection before fabrication.
Recomendado
Network Equipment Service Ports
The ADM232LJRZ can implement a local RS-232 service or management port in network and communications equipment where a single 5 V supply is preferred. Its small 16-pin SOIC footprint supports compact layouts, and the 120 kbps data rate covers common administrative and configuration protocols. The two-transmitter, two-receiver arrangement supports full-duplex console links or separate command and status channels. Use ESD protection at any user-accessible connector, maintain a low-impedance ground return, and keep switching converters and high-current traces away from the RS-232 receiver inputs to minimize noise coupling.
Recomendado
Instrumentation and Portable Analyzers
Portable analyzers and field-service instruments benefit from an RS-232 interface that operates from the same 5 V rail as the digital controller. The ADM232LJRZ provides two drivers, two receivers, and up to 120 kbps throughput while producing approximately ±9 V swing through its integrated converter. This supports communication with external sensors, printers, calibration tools, or legacy host computers. Keep the interface layout compact, use low-ESR capacitors at the charge-pump nodes, and apply connector-side protection. Verify battery operating range, common-mode ground behavior, and data reliability over the maximum intended cable length.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para ADM232LJRZ — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | MAX3232CSE | MAX3241CSE | MAX232CSE | MAX232ACSE | MAX3232EESE |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated |
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
Principais diferenciais
- Two full-duplex channels in a compact interface package (vs MAX232CSE)
- Single-supply bipolar signaling through an integrated converter (vs MAX3232CSE)
- Documented EIA-232-E and V.28 interface positioning (vs MAX3241CSE)
Notas de projeto
Place the 1 µF charge-pump capacitors directly between their designated IC pins and ground using short traces. Keep the loops compact because long capacitor connections increase switching-loop area and can reduce noise margin or alter converter behavior. Follow the Analog Devices datasheet capacitor guidance and use a dielectric suitable for the converter's voltage and ripple conditions.
Separate the RS-232 driver outputs from receiver inputs and sensitive analog traces. Connect external protection networks at the connector rather than at the transceiver, and route both signal and ground conductors together to reduce susceptibility to ground-current interference. A solid ground plane and short return path are especially important when two connected systems use different earth references.
Do not treat the ADM232LJRZ driver output as a CMOS or TTL output. The transmitter output is an RS-232-level signal intended for the external line, while receiver outputs return logic-compatible levels to the host. Verify every pin against the manufacturer pin-description table and confirm the connector pinout before powering the assembled board.
Informações de conformidade
The ADM232LJRZ product listing identifies a lead-free status field, but no explicit status is stated for RoHS, REACH, AEC-Q100, halogen-free, or conflict-minerals compliance.