ADM232LJRZ - 2/2 RS-232 Transceiver, 5V, 120kbps | Analog Devices
料号: ADM232LJRZ ✓ 量产中ADM232LJRZ 概述
An RS-232 transceiver is an interface IC that combines line drivers and line receivers with the electrical conversion required by EIA-232 links. It belongs to the RS-232 interface IC hierarchy, where a dual driver converts logic-level transmit signals into bipolar RS-232 levels and two receivers convert incoming bipolar signals back into CMOS-compatible logic. This device is intended for systems where ±12 V is unavailable, using its on-board dc-to-dc converters to generate the required positive and negative voltage swings.
Key characteristics include two transmitters, two receivers, a single 5 V supply, operation over a 4.5 V to 5.5 V input range, and a data rate of up to 120 kbps. The on-board converters produce approximately ±9 V output swing, while the charge-pump network uses small 1 µF capacitors. The interface is designed to meet EIA-232-E and V.28 requirements, making it appropriate for point-to-point serial links, instrumentation, data acquisition, and control systems.
The ADM232L family combines CMOS power-efficient logic with bipolar RS-232 signal levels. Its integrated dc-to-dc converter avoids a separate negative supply and allows the interface to operate from one 5 V rail. Because the transmitter outputs are not TTL-compatible, downstream circuitry must use the transceiver's RS-232 output levels directly rather than driving the outputs from ordinary 5 V logic without proper translation.
Typical applications include serial adapters, industrial control links, test and measurement equipment, embedded instrumentation, and communication ports that require two transmit and two receive channels. In a typical implementation, the device connects logic-level UART pins to an external DB9 or other RS-232 connector, while protection components handle electrostatic-discharge and cable-transient risks.
When laying out the PCB, place the charge-pump capacitors and interface-side protection components close to the device. Keep RS-232 driver traces away from sensitive analog inputs, and provide a solid ground reference between the transceiver and connected equipment. Confirm connector-level fault protection and cable length against the system communication requirements.
直接替换替代料: ADM232LJRZ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: ADM232LJRZ (相同外形与封装尺寸) ——差异在于 Package, Data Rate, Function, Maximum Data Rate, Operating Temperature Range.
MAX3232CSE+
✅ 直接替换联系询价
查看数据手册 →MAX3241CSE
✅ 直接替换📋 参考替代料(不在目录中)
MAX232CSE+T
✅ 直接替换联系询价
查看数据手册 →MAX232ACSE+T
✅ 直接替换联系询价
查看数据手册 →MAX3232EESE
✅ 直接替换📋 参考替代料(不在目录中)
ADM232LJRZ 规格参数
| Transceiver Configuration | 2 drivers / 2 receivers |
| 接口类型 | Full-duplex RS-232 |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Nominal Supply Voltage | 5 V |
| Maximum Data Rate | 120 kbps |
| Transmitter Output Swing | ±9 V from a 5 V supply |
| Charge-Pump Capacitor Value | 1 µF |
| Protocol Compliance | EIA-232-E and V.28 |
| 封装 | 16-pin SOIC, 7.50 mm width |
| 安装类型 | Surface mount |
| Shipping Packaging | Tube |
| On-Board DC-to-DC Converter | Yes |
| Logic Compatibility | CMOS |
ADM232LJRZ 16-pin soic, 7.50 mm width 引脚配置指南
ADM232LJRZ(16-pin soic, 7.50 mm width 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: ADM232LJRZ.
请参阅 数据手册 以查看完整引脚配置。
典型应用
ADM232LJRZ 适用于 6 应用s: Industrial Serial Control, Test and Measurement Equipment, Data Acquisition Modules, Embedded Serial Port Expansion, Network Equipment Service Ports, Instrumentation and Portable Analyzers.
Industrial Serial Control
The ADM232LJRZ fits industrial control equipment that requires two RS-232 transmit channels and two receive channels from one 5 V rail. Its 120 kbps maximum data rate is suitable for supervisory protocols, configuration links, and service interfaces. The integrated dc-to-dc converter supplies approximately ±9 V signal swing without a separate negative supply, reducing connector-side power complexity. Place the 1 µF charge-pump capacitors close to the device and route the RS-232 outputs directly toward protected connector circuitry. Industrial suitability should still be confirmed against the required ambient temperature, EMC level, isolation arrangement, and enclosure grounding strategy.
推荐
Test and Measurement Equipment
Instrumentation systems often need a compact, reliable path between a control processor and external RS-232 equipment. The ADM232LJRZ provides a 2/2 full-duplex interface, 4.5 V to 5.5 V supply operation, and throughput up to 120 kbps, which suits command and measurement-data links. Its integrated charge pump removes the need for a separate negative rail at the interface. When connecting to test equipment, use a defined ground reference and place transient protection near the external connector. Verify the protocol's baud rate, line length, connector gender, and command response timing before finalizing the system interface.
推荐
Data Acquisition Modules
The ADM232LJRZ can connect a data-acquisition controller to legacy RS-232 instruments and service ports. Two drivers and two receivers allow command traffic and returned measurements to coexist in a full-duplex arrangement, while the 120 kbps rate is appropriate for many sensor, laboratory, and process-control protocols. The single 5 V supply simplifies isolated or multi-rail system designs, and the integrated converter provides approximately ±9 V output levels. Keep sensitive analog measurement sections physically separate from the transceiver and converter area, and verify grounding carefully to prevent ground potential differences from disturbing low-level measurements.
推荐
Embedded Serial Port Expansion
An embedded controller with limited UART channels can use the ADM232LJRZ to add two bidirectional RS-232 ports. The device's 2/2 topology and 120 kbps maximum data rate suit command consoles, remote controls, and equipment-management links. Because the transmitter produces RS-232 levels rather than CMOS logic directly, connect the driver outputs to the external line and route receiver outputs back to the host UART or level-shifting logic. Confirm the controller's signal voltage and use the manufacturer pin table to verify every connection before fabrication.
推荐
Network Equipment Service Ports
The ADM232LJRZ can implement a local RS-232 service or management port in network and communications equipment where a single 5 V supply is preferred. Its small 16-pin SOIC footprint supports compact layouts, and the 120 kbps data rate covers common administrative and configuration protocols. The two-transmitter, two-receiver arrangement supports full-duplex console links or separate command and status channels. Use ESD protection at any user-accessible connector, maintain a low-impedance ground return, and keep switching converters and high-current traces away from the RS-232 receiver inputs to minimize noise coupling.
推荐
Instrumentation and Portable Analyzers
Portable analyzers and field-service instruments benefit from an RS-232 interface that operates from the same 5 V rail as the digital controller. The ADM232LJRZ provides two drivers, two receivers, and up to 120 kbps throughput while producing approximately ±9 V swing through its integrated converter. This supports communication with external sensors, printers, calibration tools, or legacy host computers. Keep the interface layout compact, use low-ESR capacitors at the charge-pump nodes, and apply connector-side protection. Verify battery operating range, common-mode ground behavior, and data reliability over the maximum intended cable length.
推荐
推荐产品汇总
工程参考数据: ADM232LJRZ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MAX3232CSE | MAX3241CSE | MAX232CSE | MAX232ACSE | MAX3232EESE |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated |
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
关键差异点
- Two full-duplex channels in a compact interface package (对比 MAX232CSE)
- Single-supply bipolar signaling through an integrated converter (对比 MAX3232CSE)
- Documented EIA-232-E and V.28 interface positioning (对比 MAX3241CSE)
设计说明
Place the 1 µF charge-pump capacitors directly between their designated IC pins and ground using short traces. Keep the loops compact because long capacitor connections increase switching-loop area and can reduce noise margin or alter converter behavior. Follow the Analog Devices datasheet capacitor guidance and use a dielectric suitable for the converter's voltage and ripple conditions.
Separate the RS-232 driver outputs from receiver inputs and sensitive analog traces. Connect external protection networks at the connector rather than at the transceiver, and route both signal and ground conductors together to reduce susceptibility to ground-current interference. A solid ground plane and short return path are especially important when two connected systems use different earth references.
Do not treat the ADM232LJRZ driver output as a CMOS or TTL output. The transmitter output is an RS-232-level signal intended for the external line, while receiver outputs return logic-compatible levels to the host. Verify every pin against the manufacturer pin-description table and confirm the connector pinout before powering the assembled board.
合规信息
The ADM232LJRZ product listing identifies a lead-free status field, but no explicit status is stated for RoHS, REACH, AEC-Q100, halogen-free, or conflict-minerals compliance.