Analog Devices

ADM232LJRZ - 2/2 RS-232 Transceiver, 5V, 120kbps | Analog Devices

MPN: ADM232LJRZ ✓ 啟用中
4.5 V to 5.5 V Vdss 16-pin SOIC, 7.50 mm width Package
MOQ: 1 |

ADM232LJRZ 概覽

The Analog Devices ADM232LJRZ is a 2/2 full-duplex RS-232 transceiver operating from a single 4.5 V to 5.5 V supply, with a maximum data rate of 120 kbps and ±9 V output swing from a 5 V supply. The device is packaged in a 16-pin SOIC for compact industrial, instrumentation, and embedded communication equipment.

An RS-232 transceiver is an interface IC that combines line drivers and line receivers with the electrical conversion required by EIA-232 links. It belongs to the RS-232 interface IC hierarchy, where a dual driver converts logic-level transmit signals into bipolar RS-232 levels and two receivers convert incoming bipolar signals back into CMOS-compatible logic. This device is intended for systems where ±12 V is unavailable, using its on-board dc-to-dc converters to generate the required positive and negative voltage swings.

Key characteristics include two transmitters, two receivers, a single 5 V supply, operation over a 4.5 V to 5.5 V input range, and a data rate of up to 120 kbps. The on-board converters produce approximately ±9 V output swing, while the charge-pump network uses small 1 µF capacitors. The interface is designed to meet EIA-232-E and V.28 requirements, making it appropriate for point-to-point serial links, instrumentation, data acquisition, and control systems.

The ADM232L family combines CMOS power-efficient logic with bipolar RS-232 signal levels. Its integrated dc-to-dc converter avoids a separate negative supply and allows the interface to operate from one 5 V rail. Because the transmitter outputs are not TTL-compatible, downstream circuitry must use the transceiver's RS-232 output levels directly rather than driving the outputs from ordinary 5 V logic without proper translation.

Typical applications include serial adapters, industrial control links, test and measurement equipment, embedded instrumentation, and communication ports that require two transmit and two receive channels. In a typical implementation, the device connects logic-level UART pins to an external DB9 or other RS-232 connector, while protection components handle electrostatic-discharge and cable-transient risks.

When laying out the PCB, place the charge-pump capacitors and interface-side protection components close to the device. Keep RS-232 driver traces away from sensitive analog inputs, and provide a solid ground reference between the transceiver and connected equipment. Confirm connector-level fault protection and cable length against the system communication requirements.

直接替換替代品,適用於 ADM232LJRZ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

此系列的變體

與下列產品可直接替換的同系列型號: ADM232LJRZ (相同外形與佔位) — 差異在於 Package, Data Rate, Function, Maximum Data Rate, Operating Temperature Range.

Analog Devices
Package: 16-SOIC (NSOIC, narrow body, 0.154" / 3.90 mm width)
Data Rate: 200 kbps
Function: RS-232 Transceiver (2 Driver / 2 Receiver)
比較對象 ADM232LJRZ →
Analog Devices
Package: 16-pin Narrow SOIC (SOIC-N-16)
Data Rate: 120 kb/s
Function: RS-232 Line Driver/Receiver (Transceiver)
比較對象 ADM232LJRZ →
Maxim Integrated
Package: 16-SOIC narrow
Maximum Data Rate: Up to 1Mbps
Operating Temperature Range: 0C to +70C
比較對象 ADM232LJRZ →

MAX3232CSE+

✅ 直接替換
Maxim Integrated
📦 16-SOIC
Dual RS-232 transceiver · 2 · 2 · 3.0V to 5.5V · Up to 1Mbps · True RS-232 · RS-232, CMOS · Low-power

聯絡詢價

查看資料表 →

MAX3241CSE

✅ 直接替換
📦 16-SOIC
Same 2/2 channel count and single 5 V RS-232 function; timing, control-pin behavior, and capacitor requirements must be cross-checked.

📋 參考替代品(不在目錄中)

MAX232CSE+T

✅ 直接替換
Analog Devices
📦 16-SOIC
RS-232 Line Driver/Receiver (Transceiver) · 2 · 2 · RS-232 (EIA/TIA-232E, V.28/V.24) · 4.5 V to 5.5 V (single +5V supply) · 120 kb/s · ±7.5 V minimum (typical ±9 V) into 3 kΩ load · ±30 V

聯絡詢價

查看資料表 →

MAX232ACSE+T

✅ 直接替換
Analog Devices
📦 16-SOIC
RS-232 Transceiver (2 Driver / 2 Receiver) · 200 kbps · 4.5 V to 5.5 V · 2 · 2 · Full · ±30 V (HBM ESD tolerance on RS-232 inputs) · 0 °C to +70 °C (C grade)

聯絡詢價

查看資料表 →

MAX3232EESE

✅ 直接替換
📦 16-SOIC
Same 2/2 RS-232 configuration, 5 V supply class, and 120 kbps-class interface; temperature-grade and timing differences require verification.

📋 參考替代品(不在目錄中)

ADM232LJRZ 規格

Transceiver Configuration 2 drivers / 2 receivers
介面類型 Full-duplex RS-232
Supply Voltage Range 4.5 V to 5.5 V
Nominal Supply Voltage 5 V
Maximum Data Rate 120 kbps
Transmitter Output Swing ±9 V from a 5 V supply
Charge-Pump Capacitor Value 1 µF
Protocol Compliance EIA-232-E and V.28
封裝 16-pin SOIC, 7.50 mm width
安裝類型 Surface mount
Shipping Packaging Tube
On-Board DC-to-DC Converter Yes
Logic Compatibility CMOS

ADM232LJRZ 16-pin soic, 7.50 mm width 腳位配置指南

ADM232LJRZ(16-pin soic, 7.50 mm width 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。

ADM232LJRZ 的 16-pin soic, 7.50 mm width 封裝腳位圖

無詳細腳位定義資料: ADM232LJRZ.

請參閱 資料表 以查看完整腳位配置。

典型應用

ADM232LJRZ 適用於 6 應用s: Industrial Serial Control, Test and Measurement Equipment, Data Acquisition Modules, Embedded Serial Port Expansion, Network Equipment Service Ports, Instrumentation and Portable Analyzers.

🏭

Industrial Serial Control

The ADM232LJRZ fits industrial control equipment that requires two RS-232 transmit channels and two receive channels from one 5 V rail. Its 120 kbps maximum data rate is suitable for supervisory protocols, configuration links, and service interfaces. The integrated dc-to-dc converter supplies approximately ±9 V signal swing without a separate negative supply, reducing connector-side power complexity. Place the 1 µF charge-pump capacitors close to the device and route the RS-232 outputs directly toward protected connector circuitry. Industrial suitability should still be confirmed against the required ambient temperature, EMC level, isolation arrangement, and enclosure grounding strategy.

🖥️

Test and Measurement Equipment

Instrumentation systems often need a compact, reliable path between a control processor and external RS-232 equipment. The ADM232LJRZ provides a 2/2 full-duplex interface, 4.5 V to 5.5 V supply operation, and throughput up to 120 kbps, which suits command and measurement-data links. Its integrated charge pump removes the need for a separate negative rail at the interface. When connecting to test equipment, use a defined ground reference and place transient protection near the external connector. Verify the protocol's baud rate, line length, connector gender, and command response timing before finalizing the system interface.

📟

Data Acquisition Modules

The ADM232LJRZ can connect a data-acquisition controller to legacy RS-232 instruments and service ports. Two drivers and two receivers allow command traffic and returned measurements to coexist in a full-duplex arrangement, while the 120 kbps rate is appropriate for many sensor, laboratory, and process-control protocols. The single 5 V supply simplifies isolated or multi-rail system designs, and the integrated converter provides approximately ±9 V output levels. Keep sensitive analog measurement sections physically separate from the transceiver and converter area, and verify grounding carefully to prevent ground potential differences from disturbing low-level measurements.

🧩

Embedded Serial Port Expansion

An embedded controller with limited UART channels can use the ADM232LJRZ to add two bidirectional RS-232 ports. The device's 2/2 topology and 120 kbps maximum data rate suit command consoles, remote controls, and equipment-management links. Because the transmitter produces RS-232 levels rather than CMOS logic directly, connect the driver outputs to the external line and route receiver outputs back to the host UART or level-shifting logic. Confirm the controller's signal voltage and use the manufacturer pin table to verify every connection before fabrication.

🌐

Network Equipment Service Ports

The ADM232LJRZ can implement a local RS-232 service or management port in network and communications equipment where a single 5 V supply is preferred. Its small 16-pin SOIC footprint supports compact layouts, and the 120 kbps data rate covers common administrative and configuration protocols. The two-transmitter, two-receiver arrangement supports full-duplex console links or separate command and status channels. Use ESD protection at any user-accessible connector, maintain a low-impedance ground return, and keep switching converters and high-current traces away from the RS-232 receiver inputs to minimize noise coupling.

🔧

Instrumentation and Portable Analyzers

Portable analyzers and field-service instruments benefit from an RS-232 interface that operates from the same 5 V rail as the digital controller. The ADM232LJRZ provides two drivers, two receivers, and up to 120 kbps throughput while producing approximately ±9 V swing through its integrated converter. This supports communication with external sensors, printers, calibration tools, or legacy host computers. Keep the interface layout compact, use low-ESR capacitors at the charge-pump nodes, and apply connector-side protection. Verify battery operating range, common-mode ground behavior, and data reliability over the maximum intended cable length.

What is the operating voltage of ADM232LJRZ?
The ADM232LJRZ operates from a single 4.5 V to 5.5 V supply, with 5 V as the nominal operating voltage. According to the Analog Devices manufacturer datasheet, the integrated dc-to-dc converter produces approximately ±9 V of RS-232 output swing from the 5 V rail, eliminating the need for a separate negative supply in the host system.
How many RS-232 drivers and receivers does ADM232LJRZ contain?
The ADM232LJRZ contains two transmitters and two receivers in a 2/2 configuration. According to the Analog Devices manufacturer datasheet, this supports two independent transmit paths and two independent receive paths for full-duplex RS-232 communication. Each driver converts CMOS logic into bipolar RS-232 levels, while each receiver performs the inverse conversion.
What is the maximum data rate of ADM232LJRZ?
The maximum RS-232 data rate of ADM232LJRZ is 120 kbps. The Analog Devices manufacturer datasheet identifies the interface as suitable for EIA-232-E and V.28 communications and specifies a 4.5 V to 5.5 V operating supply. Actual link throughput can be lower when cable length, capacitance, grounding, or protocol framing reduce the practical margin.
Where can I download the ADM232LJRZ datasheet PDF?
The official ADM232LJRZ product information and manufacturer datasheet are available from the Analog Devices ADM232L product page at https://www.analog.com/en/products/adm232l.html. The product page is the preferred source for the current datasheet, ordering information, package details, and lifecycle status because it is maintained by the manufacturer.
Where can I find the ADM232LJRZ pinout?
Use the pin-description table and package drawing in the Analog Devices ADM232L manufacturer datasheet when assigning PCB tracks. The ADM232LJRZ uses a 16-pin SOIC, and its external connections include the transmit outputs, receive inputs, supply, ground, charge-pump nodes, and associated bypass components described in that document.
Does ADM232LJRZ need both positive and negative power supplies?
No. The ADM232LJRZ requires only a single 4.5 V to 5.5 V supply because its on-board dc-to-dc converter generates the positive and negative voltages needed for RS-232 signaling. According to the Analog Devices manufacturer datasheet, a 5 V supply produces approximately ±9 V output swing, which simplifies the power architecture compared with conventional discrete RS-232 interfaces.
What can replace the ADM232LJRZ?
The MAX3232CSE is a practical 16-pin SOIC alternative with two RS-232 drivers, two receivers, a single 5 V supply, and a 120 kbps-class interface. Confirm the charge-pump capacitor values, shutdown behavior, receiver thresholds, and exact pin assignment in the manufacturer datasheet before treating it as a drop-in replacement.
Is MAX3232CSE the same as ADM232LJRZ?
The MAX3232CSE and ADM232LJRZ both provide a 2/2 RS-232 interface from a single 5 V supply in a 16-pin SOIC, so they are closely matched interface alternatives. They are not necessarily identical in shutdown logic, capacitor requirements, propagation delay, or protection behavior. Compare the manufacturer pin descriptions and application circuits before replacing one with the other.
ADM232LJRZ vs MAX232CSE — which is better for a 5V UART port?
The ADM232LJRZ is preferable when a confirmed 16-pin SOIC solution with 2/2 channels, a 4.5 V to 5.5 V supply range, 120 kbps operation, and documented ±9 V swing is required. The MAX232CSE is also a conventional 2/2, 5 V, 120 kbps-class alternative, but capacitor values and exact functional details must be checked before selecting it.
When should I choose ADM232LJRZ over MAX3241CSE?
Choose the ADM232LJRZ when the design has been qualified around the Analog Devices family and requires the documented 2/2 RS-232 configuration at up to 120 kbps. Consider the MAX3241CSE only after confirming that its electrical timing, control pins, capacitor network, and pin mapping satisfy the existing PCB and system requirements.
Is ADM232LJRZ suitable for industrial equipment?
The ADM232LJRZ is suitable for RS-232 communication in equipment where its 4.5 V to 5.5 V supply, 2/2 channel count, and 120 kbps data rate meet the system requirements. Industrial qualification still depends on the exact temperature grade, EMC design, isolation strategy, connector protection, and applicable equipment standards.
Where can I buy ADM232LJRZ online?
Use the Request a Quote form on this page to request the ADM232LJRZ, current commercial terms, and supply availability for the required quantity and package format. The exact stock position and lead time should be confirmed through that form so the response reflects the requested order configuration.
What is the price of ADM232LJRZ?
Current pricing for ADM232LJRZ should be requested through the Request a Quote form on this page. The form supports quantity-specific commercial review while avoiding a static price that may not reflect the selected packaging, order volume, or current component availability.
What is the lead time and stock status for ADM232LJRZ?
Current lead time, minimum order quantity, and stock status for ADM232LJRZ should be confirmed with the Request a Quote form on this page. Provide the required quantity, tube or reel preference, and production schedule so the manufacturer channel can return an accurate fulfillment proposal.
What are the key specifications of ADM232LJRZ that engineers should know?
The key ADM232LJRZ specifications are a 2/2 RS-232 configuration, 4.5 V to 5.5 V single-supply operation, 120 kbps maximum data rate, approximately ±9 V output swing, 1 µF charge-pump capacitors, and a 16-pin SOIC package. The Analog Devices manufacturer datasheet also identifies compliance with EIA-232-E and V.28 interface requirements.

工程參考資料,適用於 ADM232LJRZ — 比較、設計指引及合規資訊。

選型指南

Choose the ADM232LJRZ for a compact 2/2 RS-232 interface when the design uses a single 4.5 V to 5.5 V supply and requires data rates up to 120 kbps. Its integrated dc-to-dc converter produces approximately ±9 V swing, so no external negative supply is needed. Consider MAX3232CSE when a 16-pin SOIC alternative with closely related low-power transceiver characteristics is useful, but verify shutdown behavior and charge-pump capacitor requirements. MAX232CSE and MAX232ACSE are conventional 2/2, 5 V interface alternatives for designs using a MAX-compatible ecosystem, although timing and capacitor details must be checked. Use MAX3241CSE only after validating its control functions, timing, and exact pin mapping. For any substitution, compare the complete manufacturer pin tables, external-capacitor networks, electrical thresholds, propagation delays, and package drawing before releasing the PCB.

與替代品比較

參數 本產品 MAX3232CSE MAX3241CSE MAX232CSE MAX232ACSE MAX3232EESE
Brand Analog Devices Maxim Integrated Maxim Integrated Maxim Integrated Maxim Integrated Maxim Integrated
Package 16-SOIC 16-SOIC 16-SOIC 16-SOIC 16-SOIC 16-SOIC

主要差異化特點

  • Two full-duplex channels in a compact interface package (對比MAX232CSE)
  • Single-supply bipolar signaling through an integrated converter (對比MAX3232CSE)
  • Documented EIA-232-E and V.28 interface positioning (對比MAX3241CSE)

設計說明

Place the 1 µF charge-pump capacitors directly between their designated IC pins and ground using short traces. Keep the loops compact because long capacitor connections increase switching-loop area and can reduce noise margin or alter converter behavior. Follow the Analog Devices datasheet capacitor guidance and use a dielectric suitable for the converter's voltage and ripple conditions.

Separate the RS-232 driver outputs from receiver inputs and sensitive analog traces. Connect external protection networks at the connector rather than at the transceiver, and route both signal and ground conductors together to reduce susceptibility to ground-current interference. A solid ground plane and short return path are especially important when two connected systems use different earth references.

Do not treat the ADM232LJRZ driver output as a CMOS or TTL output. The transmitter output is an RS-232-level signal intended for the external line, while receiver outputs return logic-compatible levels to the host. Verify every pin against the manufacturer pin-description table and confirm the connector pinout before powering the assembled board.

合規資訊

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

The ADM232LJRZ product listing identifies a lead-free status field, but no explicit status is stated for RoHS, REACH, AEC-Q100, halogen-free, or conflict-minerals compliance.

資料驗證日期: 2026-11-14 — 資料由 XAIPART 元件工程團隊驗證及整理

相關搜尋

ADM232LJRZ datasheet ADM232LJRZ pinout ADM232LJRZ datasheet pdf ADM232LJRZ equivalent ADM232LJRZ replacement ADM232LJRZ vs MAX3232CSE ADM232LJRZ footprint ADM232LJRZ application circuit ADM232LJRZ price ADM232LJRZ stock Analog Devices ADM232LJRZ 16-SOIC ADM232L pinout

相關元件與詞彙

Analog Devices ADM232LJRZ ADM232L MAX3232CSE MAX3241CSE MAX232CSE MAX232ACSE MAX3232EESE RS-232 EIA-232-E V.28 RS-232 transceiver line driver line receiver full-duplex interface CMOS DC-to-DC converter charge-pump capacitor SOIC-16 surface mount industrial communication data acquisition test and measurement 120 kbps ±9 V output swing
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情