AKM

AK4186EN - 12-Bit Resistive Touch Controller | AKM

N.º da peça: AK4186EN ✓ Ativo
1.6 V to 3.6 V Vdss 16-QFN, 3 x 3 mm Package
MOQ: 1 |

AK4186EN Visão geral

The Asahi Kasei Microdevices/AKM AK4186EN is a low-power touchscreen controller for 4-wire and 5-wire resistive touch panels, with a 12-bit SAR A/D converter and an I2C serial interface in a 16-QFN 3 x 3 mm package. It operates from a 1.6 V to 3.6 V supply, making it suitable for systems powered by low-voltage microprocessors.

A touchscreen controller is an interface IC that converts the electrical response of a resistive panel into digital position and pressure data. It sits between the analog touch-panel electrodes and the digital host processor. In the system hierarchy, the AK4186EN belongs to the touchscreen-controller family, interface IC category, and broader semiconductor or embedded-control ecosystem.

Key features include support for both 4-wire and 5-wire resistive panels, a 12-bit successive-approximation-register A/D converter, and a sampling rate of 22.2 kHz. The 12-bit conversion resolution preserves fine movement distinctions in touch-driven menus, while the 22.2 kHz sampling rate supports responsive input sampling in consumer and embedded human-interface systems.

The serial I2C interface allows the controller to connect to a host processor over a compact two-wire bus, reducing the number of external connections compared with parallel controller solutions. Its 1.6 V minimum operating voltage supports direct operation in low-voltage embedded designs where the host uses a 1.8 V or 2.5 V supply. The 3 x 3 mm QFN package also supports compact panel-module layouts.

Typical uses include handheld terminals, panelized control interfaces, industrial operator panels, instrumentation, and compact portable products that employ 4-wire or 5-wire resistive touchscreens. Controller selection should match the panel wiring topology, touchscreen impedance, sampling requirements, host I2C implementation, and mechanical footprint.

For layout work, use the pin-description table and typical application circuit in the manufacturer datasheet to assign the analog touch inputs, supply rails, ground connections, and I2C signals. Validate the complete panel-to-controller signal path against the actual touch-panel impedance and the host firmware sampling configuration before production release.

This page combines the device function, electrical envelope, package identity, application guidance, and design cautions in one engineering-focused reference. It also identifies the drop-in-replacement gap identified by cross-reference research, so engineers can avoid assuming that electrically similar touchscreen controllers are pin-compatible.

Alternativas drop-in para AK4186EN — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.

Nenhuma alternativa drop-in disponível para este produto.

Solicitar alternativas

AK4186EN Especificações

Device Type Low-power resistive touchscreen controller
Supported Touch Panel Types 4-wire and 5-wire resistive
A/D Converter Resolution 12 bit
A/D Converter Architecture SAR
Supply Voltage Range 1.6 V to 3.6 V
Taxa de amostragem 22.2 kHz
Host Interface I2C serial interface
Encapsulamento 16-QFN, 3 x 3 mm
Tipo de montagem Surface mount

Guia de Configuração de Pinos do AK4186EN 16-qfn, 3 x 3 mm

Configuração de pinos para AK4186EN (pacote 16-qfn, 3 x 3 mm). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.

Diagrama de pinagem do pacote 16-qfn, 3 x 3 mm para AK4186EN

Nenhum dado detalhado de pinagem disponível para AK4186EN.

Consulte a ficha técnica para a configuração completa dos pinos.

Aplicações típicas

AK4186EN é adequado para 6 aplicaçãos: Handheld Terminal Touch Panel, Industrial Operator Panel, Test and Measurement Instrument Panel, Security and Access Control Keypad, Battery-Powered Portable Instrument, Embedded HMI Control Module.

📱

Handheld Terminal Touch Panel

The AK4186EN fits handheld terminals that use a resistive touchscreen and need a compact controller beside the host processor. Its 12-bit SAR A/D converter and 22.2 kHz sampling rate support frequent position updates, while the 16-QFN 3 x 3 mm package preserves board area. Connect the panel electrodes according to the manufacturer application circuit and communicate with the processor through I2C. The 1.6 V to 3.6 V supply range supports low-voltage portable designs.

🏭

Industrial Operator Panel

The AK4186EN is suitable for compact industrial operator panels built around 4-wire or 5-wire resistive glass. The 12-bit conversion resolution supports stable menu selection, and the 22.2 kHz sampling rate provides a practical input-update rate for touchscreen controls. Its I2C interface reduces host GPIO usage, while the 1.6 V to 3.6 V operating range simplifies integration with low-voltage embedded controllers. Validate panel impedance and environmental noise in the final enclosure.

🖥️

Test and Measurement Instrument Panel

The AK4186EN can provide front-panel touch input for test and measurement equipment that uses a resistive display or keypad-style touch surface. A 12-bit A/D converter offers a useful resolution margin for distinguishing small touch positions, and I2C keeps the connection to the instrument controller compact. The 3 x 3 mm QFN package allows placement near the panel connector, helping keep sensitive analog touch traces short. Confirm grounding and panel-impedance requirements in the target chassis.

🥑

Security and Access Control Keypad

The AK4186EN can serve as the touch-input controller for a keypad-style access-control panel. The device supports both common resistive panel topologies, provides 12-bit measurement resolution, and transfers results through I2C. Its low supply range allows operation from a 1.8 V or 2.5 V system rail, while the compact QFN package fits behind a membrane-style panel. Firmware should include debounce and coordinate-calibration logic appropriate to the mechanical touch stack.

🔋

Battery-Powered Portable Instrument

The AK4186EN suits battery-powered portable instruments that require resistive touch input without the power cost of a higher-voltage interface. The 1.6 V minimum operating voltage supports low-energy processor rails, and the I2C connection limits the number of host signals. The 12-bit converter and 22.2 kHz sampling rate provide responsive, reasonably resolved coordinates. Power-mode settings and panel-drive duty cycle should be evaluated against the instrument's battery-life target.

🧩

Embedded HMI Control Module

The AK4186EN is appropriate for embedded human-machine interface modules that use a resistive panel and communicate with an application processor over I2C. Its 16-QFN 3 x 3 mm package supports placement on a dense controller board, while the 12-bit SAR conversion supports menu navigation and parameter entry. The 1.6 V to 3.6 V operating range accommodates common embedded logic rails. Use the datasheet pin table to assign panel-drive, sense, and bus functions correctly.

Resumo dos produtos recomendados

AK7755EN AKM (Asahi Kasei Microdevices) Usado em: Handheld Terminal Touch Panel MC74F243M onsemi Usado em: Industrial Operator Panel TS974IDT STMicroelectronics Usado em: Test and Measurement Instrument Panel R5F110NJGLA#U0 Renesas Electronics Usado em: Security and Access Control Keypad XMC4500F100F256CAAXUM1 Industrial microcontroller suitable for portable-instrument control Usado em: Battery-Powered Portable Instrument XMC4300F100K256AAXQUMA1 Embedded microcontroller platform for touch-interface management Usado em: Embedded HMI Control Module
What is the AK4186EN?
The AK4186EN is a low-power touchscreen controller from Asahi Kasei Microdevices/AKM for 4-wire and 5-wire resistive touch panels. It combines a 12-bit SAR A/D converter with an I2C host interface and is housed in a 16-QFN 3 x 3 mm package. The manufacturer description identifies the device as the AK4186 low-power touchscreen controller with an I2C interface.
What supply voltage does the AK4186EN operate from?
The AK4186EN operates from 1.6 V to 3.6 V. This low-voltage range allows use with low-voltage microprocessor systems, including designs built around 1.8 V or 2.5 V rails. The AK4186 datasheet listing describes the part as a 12-bit SAR A/D converter designed for low-voltage microprocessors, while the AK4186EN datasheet listing confirms the 1.6 V to 3.6 V operating range.
Does the AK4186EN support 4-wire and 5-wire resistive touchscreens?
Yes, the AK4186EN supports both 4-wire and 5-wire resistive touchscreen technologies. Its 4-wire and 5-wire support means the controller can be evaluated for panels using either common wiring arrangement. The selected panel topology must still match the pin assignment and application circuit shown in the manufacturer datasheet, because connector order and drive or sense functions differ between the two panel types.
What is the A/D converter resolution of the AK4186EN?
The AK4186EN uses a 12-bit SAR A/D converter for touchscreen measurements. The AK4186EN datasheet description specifies the 12-bit resolution and identifies the converter architecture as successive approximation register, or SAR. Compared with an 8-bit controller, the 12-bit conversion provides finer digital separation for small changes in panel voltage and supports more precise coordinate calculation in touch-driven user interfaces.
What is the sampling rate of the AK4186EN?
The AK4186EN has a sampling rate of 22.2 kHz. This conversion rate defines how rapidly the controller can acquire successive touchscreen measurements and report new data through its I2C interface. The AK4186EN datasheet listing confirms the 22.2 kHz figure. Firmware polling intervals and the host processor response time will also influence perceived touch latency in the complete system.
Which interface connects the AK4186EN to a host processor?
The AK4186EN connects to the host processor through an I2C serial interface. I2C requires the signal, clock, and ground connections rather than a parallel data bus, helping conserve board area and host GPIO resources. The manufacturer describes the AK4186 family as a low-power touchscreen controller with an I2C interface, and the AK4186EN listing confirms that host interface.
What package does the AK4186EN use?
The AK4186EN is supplied in a 16-QFN package measuring 3 x 3 mm. The compact surface-mount format supports space-constrained handheld, panel-module, and embedded interface designs. Use the package drawing and land pattern in the manufacturer datasheet when defining the PCB footprint; the exposed or thermal connection requirements and pin numbering must also be followed exactly.
Where can I download the AK4186EN datasheet PDF?
The AK4186EN datasheet PDF is available through the manufacturer datasheet link on this page and through the AK4186 documentation listing. The primary manufacturer-document link is https://pdf.digi-electronics.com/pdf/288/AK4186EN-datasheet.pdf. Use the pin-description table, electrical characteristics, and typical application circuit for footprint assignment, host-bus configuration, and panel-specific validation.
Where can I find the AK4186EN pinout?
The AK4186EN pin assignment is defined in the manufacturer datasheet, including the touch-panel drive and sense connections, supply pins, ground pins, and I2C signals. Use the pin-description table and package drawing rather than relying on an inferred connector order, because 4-wire and 5-wire panels assign different functions to their electrodes. Confirm every net against the datasheet before releasing the PCB layout.
What is the best drop-in replacement for the AK4186EN?
No verified pin-to-pin drop-in replacement for the AK4186EN was identified in the available cross-reference results. A touchscreen controller must match the package footprint, pin functions, supply range, panel-drive topology, I2C behavior, and conversion performance, so a merely similar part is not automatically a replacement. Use the Request a Quote form on this page to ask about sourcing options, and require manufacturer pin-level confirmation before substituting a candidate.
Can an AK4186EN be replaced by another resistive touchscreen controller?
The AK4186EN can be replaced only after confirming mechanical, electrical, and firmware compatibility with the candidate controller. The critical checks are the 16-QFN 3 x 3 mm footprint, 1.6 V to 3.6 V supply range, 4-wire or 5-wire panel support, 12-bit conversion requirement, 22.2 kHz sampling behavior, and I2C register compatibility. The available cross-reference search did not verify a qualified drop-in candidate.
When should I choose the AK4186EN for a touch interface?
Choose the AK4186EN when the design uses a 4-wire or 5-wire resistive panel and benefits from a 12-bit SAR converter, a 22.2 kHz sampling rate, and an I2C host connection. Its 1.6 V to 3.6 V operating range supports low-voltage embedded systems, while the 3 x 3 mm 16-QFN package suits space-constrained boards. Confirm panel compatibility and host firmware requirements before committing the design.
Is the AK4186EN suitable for low-voltage microprocessor systems?
Yes, the AK4186EN is suitable for low-voltage microprocessor systems because its supply range is 1.6 V to 3.6 V and its I2C interface requires relatively few host connections. The device description specifically identifies the AK4186 as designed for low-voltage microprocessors. Interface voltage, pull-up requirements, timing, and panel-drive details must still be checked against the host design.
What are the key specifications of AK4186EN that engineers should know?
The AK4186EN supports 4-wire and 5-wire resistive panels, uses a 12-bit SAR A/D converter, samples at 22.2 kHz, and communicates through I2C. It operates from 1.6 V to 3.6 V and comes in a 16-QFN 3 x 3 mm package. These figures define the core electrical and mechanical envelope for panel selection, host interfacing, and PCB design.
What can replace the AK4186EN?
No alternative was verified as a direct replacement for the AK4186EN. The essential replacement criteria are the same 16-QFN 3 x 3 mm land pattern, identical or safely compatible pin functions, 1.6 V to 3.6 V operation, equivalent 4-wire and 5-wire panel handling, and compatible I2C timing and data handling. Request sourcing assistance through the Request a Quote form on this page rather than assuming a generic controller is interchangeable.
How do I buy the AK4186EN online and check current availability?
Use the Request a Quote form on this page to request current AK4186EN pricing, stock confirmation, and delivery scheduling. The available product listings identify the AK4186EN as an orderable touchscreen controller, but no fixed quantity-break price table or guaranteed inventory figure is published for quotation. Provide the required quantity, target date, and packaging preference with the request to receive an actionable commercial response.
What is the lead time for the AK4186EN?
The current AK4186EN lead time is confirmed through the Request a Quote form on this page. Product availability can vary with order quantity and procurement conditions, so engineers should submit the required quantity, target delivery date, and acceptable package format with the request. The same form can provide current pricing and stock status instead of relying on a static schedule.
What is the price of the AK4186EN?
Current AK4186EN pricing is available through the Request a Quote form on this page. The available listings describe pricing, availability, and lead time as quotation-dependent rather than publishing a stable quantity-break table. Submit the required order quantity and any target date, and the supplier can return current commercial terms for the exact AK4186EN ordering configuration.

Dados de referência de engenharia para AK4186EN — comparação, orientação de projeto e informações de conformidade.

Guia de seleção

Choose the AK4186EN when the target panel is a 4-wire or 5-wire resistive touchscreen and the host system benefits from a compact, low-voltage controller with a 12-bit SAR A/D converter and I2C communication. Its 1.6 V to 3.6 V operating range, 22.2 kHz sampling rate, and 16-QFN 3 x 3 mm package form the core selection criteria. No verified direct drop-in substitute was identified, so a cross-brand controller should be considered only after its footprint, pin functions, panel-drive behavior, electrical limits, and host-interface compatibility have been confirmed. For projects requiring a capacitive panel, a controller specified for capacitive sensing technology is necessary even if the mechanical package happens to be similar. For designs needing a larger touch-panel channel count, higher conversion throughput, or a different host protocol, choose a controller whose data-sheet requirements explicitly match those system requirements rather than forcing the AK4186EN into an incompatible design.

Notas de projeto

Use the manufacturer pin-description table and package drawing to assign every AK4186EN net before routing the PCB. Keep the 4-wire or 5-wire panel electrode connections consistent with the selected topology, and verify the 16-QFN 3 x 3 mm land pattern against the mechanical outline. Do not infer pin functions from connector order because drive, sense, I2C, supply, and ground assignments are package-specific.

Place the controller close to the touch-panel connector and return the touch-signal ground through a direct path to the device ground plane. Panel electrode impedance, cable length, and adjacent switching circuits can affect measurement quality. Validate the complete panel-to-controller path with the intended resistive glass and front-film stack, since nominal touchscreen specifications do not describe every mechanical or electrical variation.

Do not assume that two resistive touchscreen controllers are interchangeable merely because both support 4-wire and 5-wire panels. Check the 12-bit conversion requirement, 22.2 kHz sampling behavior, I2C address and timing, supply range, pin functions, and footprint. Also confirm the intended 4-wire or 5-wire panel configuration in firmware and calibration data, because incorrect electrode assignment can produce reversed or unusable coordinates.

Informações de conformidade

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Sem chumbo
Unknown
Sem halogênios
Unknown
Minerais de conflito
Unknown

The available product listings do not provide explicit compliance declarations for RoHS, REACH, lead-free status, halogen-free status, or conflict-minerals compliance. The touchscreen controller is not an automotive-qualified device in the listed documentation.

Dados verificados em: 2026-11-10 — dados verificados e curados pela equipe de engenharia de componentes da XAIPART

Buscas relacionadas

AK4186EN datasheet AK4186EN pinout AK4186EN datasheet pdf AK4186EN equivalent AK4186EN replacement AK4186EN cross reference AK4186EN 16-QFN 3x3 AK4186EN 12-bit SAR AK4186EN 22.2 kHz sampling rate AK4186EN resistive touch controller AK4186EN I2C interface AK4186EN price AK4186EN stock Asahi Kasei Microdevices AK4186EN AK4186EN 1.6V to 3.6V

Componentes & termos relacionados

Asahi Kasei Microdevices/AKM AK4186EN AK4186 resistive touchscreen controller touchscreen controller interface IC semiconductor 4-wire resistive touchscreen 5-wire resistive touchscreen 12-bit SAR A/D converter successive approximation register I2C serial interface 22.2 kHz sampling rate 1.6 V to 3.6 V supply 16-QFN 3 x 3 mm package QFN package family surface-mount device embedded human-machine interface industrial operator panel handheld terminal battery-powered instrument panel calibration touch-panel impedance
RFQ de cotação rápida
Preencha todos os detalhes — nossa equipe de vendas responderá em até 24 horas
Part number Fabricante Encapsulamento QTY Preço-alvo Total
✓
Cotação enviada!

Responderemos seu e-mail em até 24 horas

1
RFQ enviada
2
Cotação recebida
3
Pedido realizado
4
Pagamento
5
Enviado
6
Entregue
Ver detalhes da RFQ