AK4186EN - 12-Bit Resistive Touch Controller | AKM
Артикул: AK4186EN ✓ АктивенAK4186EN Обзор
A touchscreen controller is an interface IC that converts the electrical response of a resistive panel into digital position and pressure data. It sits between the analog touch-panel electrodes and the digital host processor. In the system hierarchy, the AK4186EN belongs to the touchscreen-controller family, interface IC category, and broader semiconductor or embedded-control ecosystem.
Key features include support for both 4-wire and 5-wire resistive panels, a 12-bit successive-approximation-register A/D converter, and a sampling rate of 22.2 kHz. The 12-bit conversion resolution preserves fine movement distinctions in touch-driven menus, while the 22.2 kHz sampling rate supports responsive input sampling in consumer and embedded human-interface systems.
The serial I2C interface allows the controller to connect to a host processor over a compact two-wire bus, reducing the number of external connections compared with parallel controller solutions. Its 1.6 V minimum operating voltage supports direct operation in low-voltage embedded designs where the host uses a 1.8 V or 2.5 V supply. The 3 x 3 mm QFN package also supports compact panel-module layouts.
Typical uses include handheld terminals, panelized control interfaces, industrial operator panels, instrumentation, and compact portable products that employ 4-wire or 5-wire resistive touchscreens. Controller selection should match the panel wiring topology, touchscreen impedance, sampling requirements, host I2C implementation, and mechanical footprint.
For layout work, use the pin-description table and typical application circuit in the manufacturer datasheet to assign the analog touch inputs, supply rails, ground connections, and I2C signals. Validate the complete panel-to-controller signal path against the actual touch-panel impedance and the host firmware sampling configuration before production release.
This page combines the device function, electrical envelope, package identity, application guidance, and design cautions in one engineering-focused reference. It also identifies the drop-in-replacement gap identified by cross-reference research, so engineers can avoid assuming that electrically similar touchscreen controllers are pin-compatible.
Аналоги без доработки для AK4186EN — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Для этого товара нет аналогов без доработки.
Запросить аналогиAK4186EN Характеристики
| Device Type | Low-power resistive touchscreen controller |
| Supported Touch Panel Types | 4-wire and 5-wire resistive |
| A/D Converter Resolution | 12 bit |
| A/D Converter Architecture | SAR |
| Supply Voltage Range | 1.6 V to 3.6 V |
| Частота дискретизации | 22.2 kHz |
| Host Interface | I2C serial interface |
| Корпус | 16-QFN, 3 x 3 mm |
| Тип монтажа | Surface mount |
Руководство по цоколевке AK4186EN в корпусе 16-qfn, 3 x 3 mm
Цоколевка для AK4186EN (корпус 16-qfn, 3 x 3 mm). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для AK4186EN.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
AK4186EN подходит для 6 применениеs: Handheld Terminal Touch Panel, Industrial Operator Panel, Test and Measurement Instrument Panel, Security and Access Control Keypad, Battery-Powered Portable Instrument, Embedded HMI Control Module.
Handheld Terminal Touch Panel
The AK4186EN fits handheld terminals that use a resistive touchscreen and need a compact controller beside the host processor. Its 12-bit SAR A/D converter and 22.2 kHz sampling rate support frequent position updates, while the 16-QFN 3 x 3 mm package preserves board area. Connect the panel electrodes according to the manufacturer application circuit and communicate with the processor through I2C. The 1.6 V to 3.6 V supply range supports low-voltage portable designs.
Рекомендуется
Industrial Operator Panel
The AK4186EN is suitable for compact industrial operator panels built around 4-wire or 5-wire resistive glass. The 12-bit conversion resolution supports stable menu selection, and the 22.2 kHz sampling rate provides a practical input-update rate for touchscreen controls. Its I2C interface reduces host GPIO usage, while the 1.6 V to 3.6 V operating range simplifies integration with low-voltage embedded controllers. Validate panel impedance and environmental noise in the final enclosure.
Рекомендуется
Test and Measurement Instrument Panel
The AK4186EN can provide front-panel touch input for test and measurement equipment that uses a resistive display or keypad-style touch surface. A 12-bit A/D converter offers a useful resolution margin for distinguishing small touch positions, and I2C keeps the connection to the instrument controller compact. The 3 x 3 mm QFN package allows placement near the panel connector, helping keep sensitive analog touch traces short. Confirm grounding and panel-impedance requirements in the target chassis.
Рекомендуется
Security and Access Control Keypad
The AK4186EN can serve as the touch-input controller for a keypad-style access-control panel. The device supports both common resistive panel topologies, provides 12-bit measurement resolution, and transfers results through I2C. Its low supply range allows operation from a 1.8 V or 2.5 V system rail, while the compact QFN package fits behind a membrane-style panel. Firmware should include debounce and coordinate-calibration logic appropriate to the mechanical touch stack.
Рекомендуется
Battery-Powered Portable Instrument
The AK4186EN suits battery-powered portable instruments that require resistive touch input without the power cost of a higher-voltage interface. The 1.6 V minimum operating voltage supports low-energy processor rails, and the I2C connection limits the number of host signals. The 12-bit converter and 22.2 kHz sampling rate provide responsive, reasonably resolved coordinates. Power-mode settings and panel-drive duty cycle should be evaluated against the instrument's battery-life target.
Рекомендуется
Embedded HMI Control Module
The AK4186EN is appropriate for embedded human-machine interface modules that use a resistive panel and communicate with an application processor over I2C. Its 16-QFN 3 x 3 mm package supports placement on a dense controller board, while the 12-bit SAR conversion supports menu navigation and parameter entry. The 1.6 V to 3.6 V operating range accommodates common embedded logic rails. Use the datasheet pin table to assign panel-drive, sense, and bus functions correctly.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для AK4186EN — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Заметки по проектированию
Use the manufacturer pin-description table and package drawing to assign every AK4186EN net before routing the PCB. Keep the 4-wire or 5-wire panel electrode connections consistent with the selected topology, and verify the 16-QFN 3 x 3 mm land pattern against the mechanical outline. Do not infer pin functions from connector order because drive, sense, I2C, supply, and ground assignments are package-specific.
Place the controller close to the touch-panel connector and return the touch-signal ground through a direct path to the device ground plane. Panel electrode impedance, cable length, and adjacent switching circuits can affect measurement quality. Validate the complete panel-to-controller path with the intended resistive glass and front-film stack, since nominal touchscreen specifications do not describe every mechanical or electrical variation.
Do not assume that two resistive touchscreen controllers are interchangeable merely because both support 4-wire and 5-wire panels. Check the 12-bit conversion requirement, 22.2 kHz sampling behavior, I2C address and timing, supply range, pin functions, and footprint. Also confirm the intended 4-wire or 5-wire panel configuration in firmware and calibration data, because incorrect electrode assignment can produce reversed or unusable coordinates.
Информация о соответствии
The available product listings do not provide explicit compliance declarations for RoHS, REACH, lead-free status, halogen-free status, or conflict-minerals compliance. The touchscreen controller is not an automotive-qualified device in the listed documentation.