AK4186EN - 12-Bit Resistive Touch Controller | AKM
MPN: AK4186EN ✓ 啟用中AK4186EN 概覽
A touchscreen controller is an interface IC that converts the electrical response of a resistive panel into digital position and pressure data. It sits between the analog touch-panel electrodes and the digital host processor. In the system hierarchy, the AK4186EN belongs to the touchscreen-controller family, interface IC category, and broader semiconductor or embedded-control ecosystem.
Key features include support for both 4-wire and 5-wire resistive panels, a 12-bit successive-approximation-register A/D converter, and a sampling rate of 22.2 kHz. The 12-bit conversion resolution preserves fine movement distinctions in touch-driven menus, while the 22.2 kHz sampling rate supports responsive input sampling in consumer and embedded human-interface systems.
The serial I2C interface allows the controller to connect to a host processor over a compact two-wire bus, reducing the number of external connections compared with parallel controller solutions. Its 1.6 V minimum operating voltage supports direct operation in low-voltage embedded designs where the host uses a 1.8 V or 2.5 V supply. The 3 x 3 mm QFN package also supports compact panel-module layouts.
Typical uses include handheld terminals, panelized control interfaces, industrial operator panels, instrumentation, and compact portable products that employ 4-wire or 5-wire resistive touchscreens. Controller selection should match the panel wiring topology, touchscreen impedance, sampling requirements, host I2C implementation, and mechanical footprint.
For layout work, use the pin-description table and typical application circuit in the manufacturer datasheet to assign the analog touch inputs, supply rails, ground connections, and I2C signals. Validate the complete panel-to-controller signal path against the actual touch-panel impedance and the host firmware sampling configuration before production release.
This page combines the device function, electrical envelope, package identity, application guidance, and design cautions in one engineering-focused reference. It also identifies the drop-in-replacement gap identified by cross-reference research, so engineers can avoid assuming that electrically similar touchscreen controllers are pin-compatible.
直接替換替代品,適用於 AK4186EN — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此產品無可直接替換的替代品。
申請替代品AK4186EN 規格
| Device Type | Low-power resistive touchscreen controller |
| Supported Touch Panel Types | 4-wire and 5-wire resistive |
| A/D Converter Resolution | 12 bit |
| A/D Converter Architecture | SAR |
| Supply Voltage Range | 1.6 V to 3.6 V |
| 取樣率 | 22.2 kHz |
| Host Interface | I2C serial interface |
| 封裝 | 16-QFN, 3 x 3 mm |
| 安裝類型 | Surface mount |
AK4186EN 16-qfn, 3 x 3 mm 腳位配置指南
AK4186EN(16-qfn, 3 x 3 mm 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: AK4186EN.
請參閱 資料表 以查看完整腳位配置。
典型應用
AK4186EN 適用於 6 應用s: Handheld Terminal Touch Panel, Industrial Operator Panel, Test and Measurement Instrument Panel, Security and Access Control Keypad, Battery-Powered Portable Instrument, Embedded HMI Control Module.
Handheld Terminal Touch Panel
The AK4186EN fits handheld terminals that use a resistive touchscreen and need a compact controller beside the host processor. Its 12-bit SAR A/D converter and 22.2 kHz sampling rate support frequent position updates, while the 16-QFN 3 x 3 mm package preserves board area. Connect the panel electrodes according to the manufacturer application circuit and communicate with the processor through I2C. The 1.6 V to 3.6 V supply range supports low-voltage portable designs.
推薦
Industrial Operator Panel
The AK4186EN is suitable for compact industrial operator panels built around 4-wire or 5-wire resistive glass. The 12-bit conversion resolution supports stable menu selection, and the 22.2 kHz sampling rate provides a practical input-update rate for touchscreen controls. Its I2C interface reduces host GPIO usage, while the 1.6 V to 3.6 V operating range simplifies integration with low-voltage embedded controllers. Validate panel impedance and environmental noise in the final enclosure.
推薦
Test and Measurement Instrument Panel
The AK4186EN can provide front-panel touch input for test and measurement equipment that uses a resistive display or keypad-style touch surface. A 12-bit A/D converter offers a useful resolution margin for distinguishing small touch positions, and I2C keeps the connection to the instrument controller compact. The 3 x 3 mm QFN package allows placement near the panel connector, helping keep sensitive analog touch traces short. Confirm grounding and panel-impedance requirements in the target chassis.
推薦
Security and Access Control Keypad
The AK4186EN can serve as the touch-input controller for a keypad-style access-control panel. The device supports both common resistive panel topologies, provides 12-bit measurement resolution, and transfers results through I2C. Its low supply range allows operation from a 1.8 V or 2.5 V system rail, while the compact QFN package fits behind a membrane-style panel. Firmware should include debounce and coordinate-calibration logic appropriate to the mechanical touch stack.
推薦
Battery-Powered Portable Instrument
The AK4186EN suits battery-powered portable instruments that require resistive touch input without the power cost of a higher-voltage interface. The 1.6 V minimum operating voltage supports low-energy processor rails, and the I2C connection limits the number of host signals. The 12-bit converter and 22.2 kHz sampling rate provide responsive, reasonably resolved coordinates. Power-mode settings and panel-drive duty cycle should be evaluated against the instrument's battery-life target.
推薦
Embedded HMI Control Module
The AK4186EN is appropriate for embedded human-machine interface modules that use a resistive panel and communicate with an application processor over I2C. Its 16-QFN 3 x 3 mm package supports placement on a dense controller board, while the 12-bit SAR conversion supports menu navigation and parameter entry. The 1.6 V to 3.6 V operating range accommodates common embedded logic rails. Use the datasheet pin table to assign panel-drive, sense, and bus functions correctly.
推薦
推薦產品摘要
工程參考資料,適用於 AK4186EN — 比較、設計指引及合規資訊。
選型指南
設計說明
Use the manufacturer pin-description table and package drawing to assign every AK4186EN net before routing the PCB. Keep the 4-wire or 5-wire panel electrode connections consistent with the selected topology, and verify the 16-QFN 3 x 3 mm land pattern against the mechanical outline. Do not infer pin functions from connector order because drive, sense, I2C, supply, and ground assignments are package-specific.
Place the controller close to the touch-panel connector and return the touch-signal ground through a direct path to the device ground plane. Panel electrode impedance, cable length, and adjacent switching circuits can affect measurement quality. Validate the complete panel-to-controller path with the intended resistive glass and front-film stack, since nominal touchscreen specifications do not describe every mechanical or electrical variation.
Do not assume that two resistive touchscreen controllers are interchangeable merely because both support 4-wire and 5-wire panels. Check the 12-bit conversion requirement, 22.2 kHz sampling behavior, I2C address and timing, supply range, pin functions, and footprint. Also confirm the intended 4-wire or 5-wire panel configuration in firmware and calibration data, because incorrect electrode assignment can produce reversed or unusable coordinates.
合規資訊
The available product listings do not provide explicit compliance declarations for RoHS, REACH, lead-free status, halogen-free status, or conflict-minerals compliance. The touchscreen controller is not an automotive-qualified device in the listed documentation.