Texas Instruments

CD4018BMT - 8.5MHz Divide-by-N Counter | Texas Instruments

N.º da peça: CD4018BMT ✓ Ativo
16-pin SOIC Package 8.5 MHz Speed
MOQ: 1 |

CD4018BMT Visão geral

Texas Instruments CD4018BMT is a CMOS presettable divide-by-N counter capable of dividing by values from 2 through 10, with an operating frequency listed as high as 8.5 MHz. The device is offered in a 16-pin SOIC surface-mount package and uses positive-edge clock transitions. Its counter architecture supports programmable divide ratios for frequency division, event counting, and sequential timing applications where a configurable modulus is required.

A divide-by-N counter is a digital logic IC that generates one output pulse for every N input-clock pulses. The CD4018BMT belongs to the CMOS counter and logic-IC hierarchy, combining a counter stage, programmable modulus control, and asynchronous preset and clock inputs. This makes it useful between a system oscillator and a slower sequential circuit, reducing a repetitive clock without requiring a programmable processor or complex divider chain.

The primary device characteristics include a 5-bit programmable counter section, positive-edge operation, operation in the CD4000B logic family, and an 8.5 MHz maximum listed frequency. The 16-pin SOIC package provides a compact surface-mount footprint for industrial control, test equipment, instrumentation, and embedded digital systems. Because it is a fixed-function counter, the CD4018BMT offers simpler firmware-independent timing than a microcontroller-based divider.

The CD4018BMT uses CMOS construction, which supports low static power relative to many older bipolar logic families. Its clock and control inputs are designed for normal CMOS signal levels, so system designers should verify input rise and fall times, supply voltage, and fanout against the operating conditions in the manufacturer datasheet. Decoupling close to the supply pins remains important when the counter drives clocked or switching circuitry at higher frequencies.

Typical uses include frequency division in timing modules, programmable pulse-generation circuits, digital test equipment, phase and frequency counters, and clock-staging logic. It is particularly useful when the required divide ratio is known and must remain independent of firmware. The positive-edge trigger provides predictable operation in cascaded counter arrangements, although reset and preset behavior must be coordinated to avoid unwanted intermediate states.

For reliable PCB implementation, place the device on a stable ground plane, route the clock away from switching-node traces, and use a dedicated local supply bypass capacitor close to the IC. Confirm that the clock source does not exceed the stated 8.5 MHz operating limit and that preset and reset inputs remain controlled during initialization. These precautions reduce false transitions and make the counter behavior repeatable.

This page combines the manufacturer identification, package and frequency characteristics, qualified family alternatives, application guidance, and practical design considerations into an engineering-focused view of the CD4018BMT. It helps designers determine whether this fixed-function CMOS counter satisfies their timing, packaging, and replacement requirements.

Alternativas drop-in para CD4018BMT — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.

Variantes desta série

Modelos da mesma série compatíveis como drop-in com CD4018BMT (mesmo formato e footprint) — diferindo em Counter Type, Package.

Texas Instruments
Counter Type: Divide-by-N counter
Package: 16-lead SOIC
Comparar com CD4018BMT →

CD4018BM

✅ Drop-In
Texas Instruments
📦 16-pin SOIC
CMOS presettable divide-by-N counter · 5-stage Johnson counter · 5 stages · 10 MHz at 10 V · 5 V, 10 V, and 15 V · 1 µA at 18 V · Fully static · Divide-by-N counter

Consulte o preço

Ver ficha técnica →

CD4018BM96

✅ Drop-In
📦 16-pin SOIC
Same CD4018B family, 16-pin package, 5-bit counter section, and 8.5 MHz listed frequency; ordering suffix differs

📋 Alternativa de referência (fora do catálogo)

CD4018BNSR

✅ Drop-In
📦 16-pin SOIC
Same CD4018B counter family and listed 8.5 MHz operation; ordering suffix differs by 0% in stated frequency

📋 Alternativa de referência (fora do catálogo)

CD4018BMT Classificações máximas e características elétricas

Counter Type Presettable divide-by-N counter
Logic Family CD4000B CMOS
Number of Counter Elements 1 element
Counter Width 5 bit
Maximum Operating Frequency 8.5 MHz
Trigger Type Positive edge
Divide Range 2 to 10
Output Levels CMOS
Encapsulamento 16-pin SOIC
Tipo de montagem Surface mount
Package Body Width 3.90 mm
Package Lead Pitch 1.27 mm
Presettable Yes

Guia de Configuração de Pinos do CD4018BMT 1.27 mm

Configuração de pinos para CD4018BMT (pacote 1.27 mm). Este CI digital inclui GPIO, interfaces de comunicação (UART, SPI, I2C) e pinos de alimentação. Consulte o datasheet do fabricante para funções alternativas dos pinos e opções de configuração. Essencial para projeto de sistemas embarcados e layout de PCB.

Diagrama de pinagem do pacote 1.27 mm para CD4018BMT

Nenhum dado detalhado de pinagem disponível para CD4018BMT.

Consulte a ficha técnica para a configuração completa dos pinos.

Aplicações típicas

CD4018BMT é adequado para 6 aplicaçãos: Programmable Frequency Divider, Digital Test and Measurement Timing, Pulse Generator and Sequencer, Industrial Control Event Counter, Instrumentation Clock Scaling, Frequency-to-Digital Interface.

🔧

Programmable Frequency Divider

The CD4018BMT fits programmable frequency-divider stages because it divides a positive-edge clock by a selectable value from 2 through 10 while operating up to 8.5 MHz. Place the counter between a periodic oscillator and a slower timing circuit, then select the divide ratio required by the downstream stage. This fixed-function approach eliminates counter firmware and produces a predictable pulse for each selected group of input cycles. The principal design checks are clock-edge quality, preset and reset sequencing, and keeping the source frequency within the 8.5 MHz listed limit.

🖥️

Digital Test and Measurement Timing

CD4018BMT is applicable in digital test and measurement equipment that needs a stable, reduced clock without programmable controller overhead. Its 8.5 MHz listed operating frequency allows it to process a faster reference and generate a lower-rate trigger stream for counters, timing gates, or sampling-control logic. Use the positive-edge input to establish a defined counting event and coordinate reset and preset inputs during initialization. Validate propagation delay against the timing budget of the measured or stimulated channel before releasing the design to production.

⚡

Pulse Generator and Sequencer

The CD4018BMT can generate a periodic pulse train when its input clock and programmable division ratio are configured as a simple pulse-generation stage. Positive-edge operation gives each clock event a clear counting role, while divide ratios from 2 through 10 provide practical frequency scaling. In a sequential design, use the reset and preset controls to establish a known starting condition and prevent an unintended first count. Include hysteresis or appropriate clock conditioning at the source if the oscillator waveform can cross the input threshold slowly.

🏭

Industrial Control Event Counter

CD4018BMT suits industrial control modules that must count recurring events and reduce them into a slower control pulse. Its positive-edge trigger permits counting one event per transition, and the 8.5 MHz listed operating frequency provides ample timing margin for many low-to-medium-rate event sources. Keep long external traces away from the clock input, provide a stable ground plane, and add local supply bypassing to reduce noise-induced false counts. For safety-related production use, verify the exact suffix's operating-temperature and qualification requirements before deployment.

📡

Instrumentation Clock Scaling

The CD4018BMT can scale a high-frequency internal clock into a lower-rate signal for instrumentation, timing, and control subcircuits. Its programmable division from 2 through 10 makes it useful when several subsystems require related but reduced clock rates without adding complex digital logic. Place the counter close to the receiving circuitry, preserve a continuous return path for the clock, and isolate the clock trace from switching nodes. Check the accumulated counter delay and output transition behavior against the instrument's timing margin.

🧩

Frequency-to-Digital Interface

CD4018BMT can serve as the fixed divider in an interface that converts a repetitive source frequency into a slower digital event. This arrangement is useful in alarm, timing, and repetitive-event modules where firmware does not need to count every source transition. The counter's 8.5 MHz listed operating frequency defines the upper signal-processing range, while its programmable modulus determines the event rate presented downstream. Define reset and preset states in hardware so the interface remains deterministic during power-up and fault recovery.

Resumo dos produtos recomendados

CD4018BM Texas Instruments Usado em: Programmable Frequency Divider, Digital Test and Measurement Timing, Pulse Generator and Sequencer, Instrumentation Clock Scaling CD4018BM96 Same-family counter option Usado em: Programmable Frequency Divider, Pulse Generator and Sequencer, Industrial Control Event Counter, Instrumentation Clock Scaling, Frequency-to-Digital Interface CD4018BNSR CD4018B-family counter alternative Usado em: Digital Test and Measurement Timing, Industrial Control Event Counter, Frequency-to-Digital Interface
What is the CD4018BMT?
The CD4018BMT is a Texas Instruments CMOS presettable divide-by-N counter with a 5-bit counter section, positive-edge triggering, and an operating frequency listed as high as 8.5 MHz. It is packaged in a 16-pin SOIC. According to the manufacturer product page, the device is intended for programmable frequency division, counting, and sequential timing circuits using the CD4000B logic family.
What is the operating frequency of CD4018BMT?
The CD4018BMT supports operation up to 8.5 MHz, as listed in its component specifications. This figure applies to the specified supply and operating conditions, so a design should not treat the maximum as unconditional across every voltage and temperature. Use the manufacturer datasheet to confirm clock rise and fall times, load capacitance, and propagation-delay limits for the intended circuit.
Where can I download the CD4018BMT datasheet PDF?
The official CD4018BMT documentation is available through the Texas Instruments CD4018B datasheet page at https://www.ti.com/lit/gpn/CD4018B. The manufacturer page identifies the available package and ordering options for the CD4018B family. Use the pin-description table, recommended operating conditions, and timing diagrams from that document when assigning PCB signals and calculating counter behavior.
Where can I find the CD4018BMT pinout?
The CD4018BMT pinout is published in the pin-configuration diagram contained in the official Texas Instruments CD4018B datasheet. The CD4018BMT uses a 16-pin SOIC package, but every connection must be taken from the package-specific diagram rather than inferred from another suffix. Confirm clock, reset, preset, decode, and supply assignments before laying out the board.
What are the key specifications of CD4018BMT that engineers should know?
The CD4018BMT is a 16-pin SOIC CMOS counter with a 5-bit counter section, programmable division by 2 through 10, positive-edge clock operation, and a listed maximum frequency of 8.5 MHz. The manufacturer describes it as a presettable divide-by-N counter. Its fixed-function architecture is useful when a stable frequency division ratio is required without a microcontroller or programmable divider.
Can CD4018BMT be used for frequency division?
Yes, the CD4018BMT is specifically designed for programmable divide-by-N operation. It divides a positive-edge input clock by a selected value from 2 through 10, making it appropriate for reducing a high-frequency reference to a lower periodic signal. Keep the clock within the 8.5 MHz limit and use the manufacturer timing diagrams to determine whether the selected modulus introduces the required output delay.
What is the difference between CD4018BM and CD4018BMT?
CD4018BM and CD4018BMT are both 16-pin SOIC versions of the same CD4018B counter family and have the same stated divide-by-N function, 5-bit counter section, positive-edge operation, and 8.5 MHz frequency listing. The distinction is the ordering and packaging suffix associated with the individual Texas Instruments part numbers. Verify the orderable quantity, carrier format, and marking requirements for each suffix before substitution.
Is CD4018BMT suitable for digital timing and test equipment?
The CD4018BMT is suitable for digital timing and test equipment when the required division ratio is 2 through 10 and the clock remains within the listed 8.5 MHz limit. Its fixed-function CMOS implementation reduces the need for software and provides a direct output pulse for each selected group of input pulses. Add external conditioning if the source has slow edges or an unusually high capacitive load.
What can replace CD4018BMT?
CD4018BM is the closest same-family replacement identified for the CD4018BMT because both use the 16-pin SOIC package and implement the same CD4018B divide-by-N counter function. Production substitution should still confirm pin-level connectivity, supply requirements, timing limits, temperature range, and package drawings. No unreviewed cross-brand equivalent should be used solely because its counter description appears similar.
What is the best Texas Instruments equivalent for CD4018BMT?
Texas Instruments CD4018BM is the leading same-brand option for CD4018BMT because it belongs to the same CD4018B family and uses a 16-pin SOIC package. The counter characteristics remain consistent for the divide-by-N function, positive-edge clocking, 5-bit counter section, and 8.5 MHz listed frequency. Confirm the exact ordering suffix and lifecycle requirements for the production build.
When should I choose CD4018BMT over CD4018BM?
Choose CD4018BMT when its exact orderable suffix, carrier format, and manufacturer documentation match the intended production BOM. Choose CD4018BM when that suffix better matches the required packaging and supply arrangement while retaining the same core CD4018B counter function. For either device, verify the complete pinout, electrical limits, and operating-temperature requirements rather than relying only on the counter description.
Is CD4018BMT in stock and what is its lead time?
Current stock and lead time must be confirmed for the exact CD4018BMT orderable suffix before committing a build. Use the Request a Quote form on this page to obtain current availability, minimum order quantity, and production lead time. An in-stock indication for another package suffix does not establish the status of the 16-pin SOIC CD4018BMT.
Where can I buy CD4018BMT online?
Use the Request a Quote form on this page to request CD4018BMT pricing, stock, minimum order quantity, and lead time. Quote requests reduce the risk of ordering a different CD4018B package suffix because the requested MPN remains the controlling identifier. The manufacturer documentation for the selected suffix should also be used to confirm its production status.
How do I design the PCB around CD4018BMT?
Place the CD4018BMT in its 16-pin SOIC footprint and route the clock away from switching-node and high-current traces. Add a local supply bypass capacitor close to the power pins, maintain a continuous ground reference, and avoid long parallel clock traces that can increase coupling. Follow the manufacturer pin-configuration diagram exactly and confirm that reset and preset states cannot produce unintended clock edges.
What are the main CD4018BMT design considerations?
The principal CD4018BMT design constraints are the listed 8.5 MHz operating limit, positive-edge clocking, and controlled reset and preset inputs. Clock edges must meet the timing requirements for the selected supply voltage and load, while supply bypassing should be placed close to the IC. Because the device is a CMOS counter, unused inputs should be held at a defined logic level rather than left floating.

Dados de referência de engenharia para CD4018BMT — comparação, orientação de projeto e informações de conformidade.

Guia de seleção

Choose CD4018BMT when its exact Texas Instruments ordering suffix, 16-pin SOIC package, and supply arrangement match the production design. It is appropriate for fixed frequency division, event counting, pulse generation, and timing applications requiring division from 2 through 10 with positive-edge clock operation and a listed maximum frequency of 8.5 MHz. CD4018BM is the practical same-family option when its packaging and supply configuration better fit the assembly process. CD4018BM96 and CD4018BNSR offer the same stated core counter characteristics but require verification of their individual ordering suffixes and production conditions. For any substitution, confirm pin-level connectivity, supply limits, clock timing, operating temperature, package drawings, and availability. A fixed-function counter is preferable when the division ratio is stable and firmware-free operation is valuable; a programmable counter is preferable when the modulus must change dynamically.

Comparação com alternativas

Parâmetro Este produto CD4018BM CD4018BM96 CD4018BNSR
Package 16-pin SOIC 16-pin SOIC 16-pin SOIC 16-pin SOIC
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Counter Type Presettable divide-by-N counter Presettable divide-by-N counter Presettable divide-by-N counter Presettable divide-by-N counter
Counter Width 5 bit 5 bit 5 bit 5 bit
Maximum Operating Frequency 8.5 MHz 8.5 MHz 8.5 MHz 8.5 MHz
Trigger Type Positive edge Positive edge Positive edge Positive edge
Logic Family CD4000B CMOS CD4000B CMOS CD4000B CMOS CD4000B CMOS
Presettable Yes Yes Yes Yes

Principais diferenciais

  • Exact-ordering match with the same counter characteristics (vs CD4018BM)
  • Same-family replacement without changing the core counter function (vs CD4018BM96)
  • Presettable fixed-function architecture (vs CD4018BNSR)

Notas de projeto

Route the positive-edge clock as a short, continuous trace with a nearby ground reference and keep it separated from switching-node and high-current paths. A slow clock edge can make the counter more susceptible to multiple transitions near the switching threshold, so use a clean oscillator or buffer when the source has high capacitance or a slow rise or fall time. Confirm the timing behavior against the manufacturer diagrams for the intended supply voltage and load.

Place the local supply bypass capacitor close to the CD4018BMT power and ground connections, and maintain an uninterrupted ground plane beneath the IC and its clock network. Avoid routing the clock between potential sources of crosstalk. PCB traces should follow the package drawing for the 16-pin SOIC footprint, including body width and 1.27 mm lead pitch, rather than relying on a visually similar outline.

Do not leave preset, reset, clock, or decode-related control inputs floating in a CMOS counter circuit. Define their startup states with suitable pull components or controller logic so power-up cannot create an unintended count. Also avoid assuming that every CD4018B ordering suffix has the same carrier format or production status. Confirm the exact MPN, package dimensions, temperature grade, and marking requirements before releasing a production order.

Informações de conformidade

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Sem chumbo
Unknown
Sem halogênios
Unknown
Minerais de conflito
Unknown

The manufacturer family is identified as a CD4000B CMOS logic device, but no specific environmental or material-compliance declaration is stated for the CD4018BMT ordering suffix.

Dados verificados em: 2026-11-15 — dados verificados e curados pela equipe de engenharia de componentes da XAIPART

Buscas relacionadas

CD4018BMT datasheet CD4018BMT datasheet pdf CD4018BMT pinout CD4018BMT equivalent CD4018BMT replacement CD4018BMT drop-in replacement CD4018BMT vs CD4018BM CD4018BMT 8.5MHz counter CD4018BMT 16-SOIC CD4018BMT divide by N Texas Instruments CD4018BMT CD4018BMT price CD4018BMT stock CD4018BMT application circuit CD4018BMT footprint

Componentes & termos relacionados

Texas Instruments CD4018BMT CD4018BM CD4018BM96 CD4018BNSR CD4018B CD4000B CMOS presettable divide-by-N counter counter IC logic IC digital counter frequency divider positive-edge clock 8.5 MHz 5-bit counter 16-pin SOIC SOIC package family surface-mount device SMD pulse generation digital timing event counting programmable modulus
RFQ de cotação rápida
Preencha todos os detalhes — nossa equipe de vendas responderá em até 24 horas
Part number Fabricante Encapsulamento QTY Preço-alvo Total
✓
Cotação enviada!

Responderemos seu e-mail em até 24 horas

1
RFQ enviada
2
Cotação recebida
3
Pedido realizado
4
Pagamento
5
Enviado
6
Entregue
Ver detalhes da RFQ