CD4018BMT - 8.5MHz Divide-by-N Counter | Texas Instruments
Référence : CD4018BMT ✓ ActifCD4018BMT Présentation
A divide-by-N counter is a digital logic IC that generates one output pulse for every N input-clock pulses. The CD4018BMT belongs to the CMOS counter and logic-IC hierarchy, combining a counter stage, programmable modulus control, and asynchronous preset and clock inputs. This makes it useful between a system oscillator and a slower sequential circuit, reducing a repetitive clock without requiring a programmable processor or complex divider chain.
The primary device characteristics include a 5-bit programmable counter section, positive-edge operation, operation in the CD4000B logic family, and an 8.5 MHz maximum listed frequency. The 16-pin SOIC package provides a compact surface-mount footprint for industrial control, test equipment, instrumentation, and embedded digital systems. Because it is a fixed-function counter, the CD4018BMT offers simpler firmware-independent timing than a microcontroller-based divider.
The CD4018BMT uses CMOS construction, which supports low static power relative to many older bipolar logic families. Its clock and control inputs are designed for normal CMOS signal levels, so system designers should verify input rise and fall times, supply voltage, and fanout against the operating conditions in the manufacturer datasheet. Decoupling close to the supply pins remains important when the counter drives clocked or switching circuitry at higher frequencies.
Typical uses include frequency division in timing modules, programmable pulse-generation circuits, digital test equipment, phase and frequency counters, and clock-staging logic. It is particularly useful when the required divide ratio is known and must remain independent of firmware. The positive-edge trigger provides predictable operation in cascaded counter arrangements, although reset and preset behavior must be coordinated to avoid unwanted intermediate states.
For reliable PCB implementation, place the device on a stable ground plane, route the clock away from switching-node traces, and use a dedicated local supply bypass capacitor close to the IC. Confirm that the clock source does not exceed the stated 8.5 MHz operating limit and that preset and reset inputs remain controlled during initialization. These precautions reduce false transitions and make the counter behavior repeatable.
This page combines the manufacturer identification, package and frequency characteristics, qualified family alternatives, application guidance, and practical design considerations into an engineering-focused view of the CD4018BMT. It helps designers determine whether this fixed-function CMOS counter satisfies their timing, packaging, and replacement requirements.
Alternatives de remplacement direct pour CD4018BMT — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec CD4018BMT (même facteur de forme et même empreinte) — différant par Counter Type, Package.
CD4018BM
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →CD4018BM96
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
CD4018BNSR
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
CD4018BMT Valeurs maximales et caractéristiques électriques
| Counter Type | Presettable divide-by-N counter |
| Logic Family | CD4000B CMOS |
| Number of Counter Elements | 1 element |
| Counter Width | 5 bit |
| Maximum Operating Frequency | 8.5 MHz |
| Trigger Type | Positive edge |
| Divide Range | 2 to 10 |
| Output Levels | CMOS |
| Boîtier | 16-pin SOIC |
| Type de montage | Surface mount |
| Package Body Width | 3.90 mm |
| Package Lead Pitch | 1.27 mm |
| Presettable | Yes |
Guide de configuration des broches du CD4018BMT 1.27 mm
Configuration des broches du CD4018BMT (boîtier 1.27 mm). Ce circuit intégré numérique comprend des GPIO, des interfaces de communication (UART, SPI, I2C) et des broches d'alimentation. Consultez la fiche technique du fabricant pour les fonctions alternatives des broches et les options de configuration. Indispensable pour la conception de systèmes embarqués et la conception de circuits imprimés.
Aucune donnée de brochage détaillée disponible pour CD4018BMT.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
CD4018BMT convient pour 6 applications: Programmable Frequency Divider, Digital Test and Measurement Timing, Pulse Generator and Sequencer, Industrial Control Event Counter, Instrumentation Clock Scaling, Frequency-to-Digital Interface.
Programmable Frequency Divider
The CD4018BMT fits programmable frequency-divider stages because it divides a positive-edge clock by a selectable value from 2 through 10 while operating up to 8.5 MHz. Place the counter between a periodic oscillator and a slower timing circuit, then select the divide ratio required by the downstream stage. This fixed-function approach eliminates counter firmware and produces a predictable pulse for each selected group of input cycles. The principal design checks are clock-edge quality, preset and reset sequencing, and keeping the source frequency within the 8.5 MHz listed limit.
Recommandé
Digital Test and Measurement Timing
CD4018BMT is applicable in digital test and measurement equipment that needs a stable, reduced clock without programmable controller overhead. Its 8.5 MHz listed operating frequency allows it to process a faster reference and generate a lower-rate trigger stream for counters, timing gates, or sampling-control logic. Use the positive-edge input to establish a defined counting event and coordinate reset and preset inputs during initialization. Validate propagation delay against the timing budget of the measured or stimulated channel before releasing the design to production.
Recommandé
Pulse Generator and Sequencer
The CD4018BMT can generate a periodic pulse train when its input clock and programmable division ratio are configured as a simple pulse-generation stage. Positive-edge operation gives each clock event a clear counting role, while divide ratios from 2 through 10 provide practical frequency scaling. In a sequential design, use the reset and preset controls to establish a known starting condition and prevent an unintended first count. Include hysteresis or appropriate clock conditioning at the source if the oscillator waveform can cross the input threshold slowly.
Recommandé
Industrial Control Event Counter
CD4018BMT suits industrial control modules that must count recurring events and reduce them into a slower control pulse. Its positive-edge trigger permits counting one event per transition, and the 8.5 MHz listed operating frequency provides ample timing margin for many low-to-medium-rate event sources. Keep long external traces away from the clock input, provide a stable ground plane, and add local supply bypassing to reduce noise-induced false counts. For safety-related production use, verify the exact suffix's operating-temperature and qualification requirements before deployment.
Recommandé
Instrumentation Clock Scaling
The CD4018BMT can scale a high-frequency internal clock into a lower-rate signal for instrumentation, timing, and control subcircuits. Its programmable division from 2 through 10 makes it useful when several subsystems require related but reduced clock rates without adding complex digital logic. Place the counter close to the receiving circuitry, preserve a continuous return path for the clock, and isolate the clock trace from switching nodes. Check the accumulated counter delay and output transition behavior against the instrument's timing margin.
Recommandé
Frequency-to-Digital Interface
CD4018BMT can serve as the fixed divider in an interface that converts a repetitive source frequency into a slower digital event. This arrangement is useful in alarm, timing, and repetitive-event modules where firmware does not need to count every source transition. The counter's 8.5 MHz listed operating frequency defines the upper signal-processing range, while its programmable modulus determines the event rate presented downstream. Define reset and preset states in hardware so the interface remains deterministic during power-up and fault recovery.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour CD4018BMT — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | CD4018BM | CD4018BM96 | CD4018BNSR |
|---|---|---|---|---|
| Package | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Counter Type | Presettable divide-by-N counter | Presettable divide-by-N counter | Presettable divide-by-N counter | Presettable divide-by-N counter |
| Counter Width | 5 bit | 5 bit | 5 bit | 5 bit |
| Maximum Operating Frequency | 8.5 MHz | 8.5 MHz | 8.5 MHz | 8.5 MHz |
| Trigger Type | Positive edge | Positive edge | Positive edge | Positive edge |
| Logic Family | CD4000B CMOS | CD4000B CMOS | CD4000B CMOS | CD4000B CMOS |
| Presettable | Yes | Yes | Yes | Yes |
Principaux différenciateurs
- Exact-ordering match with the same counter characteristics (vs CD4018BM)
- Same-family replacement without changing the core counter function (vs CD4018BM96)
- Presettable fixed-function architecture (vs CD4018BNSR)
Notes de conception
Route the positive-edge clock as a short, continuous trace with a nearby ground reference and keep it separated from switching-node and high-current paths. A slow clock edge can make the counter more susceptible to multiple transitions near the switching threshold, so use a clean oscillator or buffer when the source has high capacitance or a slow rise or fall time. Confirm the timing behavior against the manufacturer diagrams for the intended supply voltage and load.
Place the local supply bypass capacitor close to the CD4018BMT power and ground connections, and maintain an uninterrupted ground plane beneath the IC and its clock network. Avoid routing the clock between potential sources of crosstalk. PCB traces should follow the package drawing for the 16-pin SOIC footprint, including body width and 1.27 mm lead pitch, rather than relying on a visually similar outline.
Do not leave preset, reset, clock, or decode-related control inputs floating in a CMOS counter circuit. Define their startup states with suitable pull components or controller logic so power-up cannot create an unintended count. Also avoid assuming that every CD4018B ordering suffix has the same carrier format or production status. Confirm the exact MPN, package dimensions, temperature grade, and marking requirements before releasing a production order.
Informations de conformité
The manufacturer family is identified as a CD4000B CMOS logic device, but no specific environmental or material-compliance declaration is stated for the CD4018BMT ordering suffix.