Texas Instruments

DS90CR285MTD - 28-Bit 66MHz LVDS Transmitter | Texas Instruments

N.º da peça: DS90CR285MTD ✓ Ativo
3.3 V Vdss 56-pin TSSOP Package 66 MHz Speed
MOQ: 1 |

DS90CR285MTD Visão geral

The Texas Instruments DS90CR285MTD is a 28-bit Channel Link LVDS transmitter operating from a 3.3 V supply and supporting a 66 MHz rising-edge data strobe. The device converts 28 LVCMOS/LVTTL input bits into four differential LVDS data streams and transmits a phase-locked differential clock over a fifth LVDS link. It is housed in a 56-pin TSSOP package rated for -40°C to +85°C operation.

An LVDS transmitter is a high-speed interface device that converts low-voltage complementary logic into balanced differential signals. LVDS belongs to the broader differential-interface and data-transceiver hierarchy, where low signal amplitude, common-mode rejection, and reduced electromagnetic interference support reliable point-to-point data transfer. DS90CR285 devices are commonly positioned between parallel digital logic and a high-speed LVDS link on displays, industrial controllers, and communications equipment.

The principal features include 28 parallel data inputs, four LVDS data outputs, one additional LVDS clock output, and a 66 MHz maximum parallel-clock frequency. The transmitted clock is phase-locked to the source data, allowing the receiving system to recover timing. The device also accepts a rising-edge data strobe and operates from a single 3.3 V supply. Its 56-pin TSSOP package provides a conventional surface-mount interface for systems using high-density parallel-to-differential signaling.

The transmitter architecture divides the 28-bit parallel payload into four differential data lanes and provides a separate clock lane. This arrangement limits the number of high-speed differential conductors required to carry the payload. Compared with single-ended parallel transmission, the balanced outputs improve noise immunity and can reduce connector and PCB signal-integrity problems when the receiver, termination network, trace geometry, and clock distribution are designed correctly.

Typical uses include digital display interfaces, flat-panel monitor backplane links, industrial imaging equipment, video-processing systems, test equipment, and embedded control systems that exchange parallel data over a short differential cable or board-level LVDS connection. The transmitter is also suitable where a source device has a 28-bit parallel bus but the destination requires a smaller number of low-voltage differential conductors.

PCB implementation should treat the LVDS outputs as controlled-impedance differential pairs. Route each pair continuously over a solid reference plane, keep the spacing within the pair consistent, and place the receiver-side termination close to the receiver. Avoid adding test pads or routing discontinuities that create impedance mismatches, and verify AC-coupled or DC-coupled connectivity against the receiver's input requirements.

This product record combines the device's key interface characteristics, package information, sourcing guidance, compatible ordering variants, and practical implementation considerations. It helps engineers identify the correct Texas Instruments LVDS transmitter, compare its electrically identical ordering options, and plan a robust 28-bit parallel-to-LVDS interface before committing a PCB layout.

Alternativas drop-in para DS90CR285MTD — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.

Variantes desta série

Modelos da mesma série compatíveis como drop-in com DS90CR285MTD (mesmo formato e footprint) — diferindo em Package, Product Type, Supply Voltage, Packaging.

Texas Instruments
Package: 48-TSSOP, 6.10 mm width
Product Type: 18-bit LVDS flat-panel display receiver
Supply Voltage: 3.3 V nominal
Comparar com DS90CR285MTD →
Texas Instruments
Package: 56-TSSOP (0.240, 6.10 mm width)
Product Type: 28-Bit Channel Link Transmitter
Packaging: Tube
Comparar com DS90CR285MTD →
Texas Instruments
Supply Voltage: 4.75 V ~ 5.25 V
Packaging: Tape & Reel (TR)

DS90CR285MTD/NOPB

✅ Drop-In
📦 56-pin TSSOP
Same 28-bit input, four LVDS data outputs, fifth LVDS clock link, 3.3 V supply, and 66 MHz clock; ordering suffix differs by 0% in core interface ratings

📋 Alternativa de referência (fora do catálogo)

DS90CR285MTDX

✅ Drop-In
📦 56-pin TSSOP
Same 28-bit, 66 MHz, 3.3 V LVDS transmitter ratings and 56-pin TSSOP footprint; delivery-code suffix differs by 0% in core interface ratings

📋 Alternativa de referência (fora do catálogo)

DS90CR285MTD Especificações

Product Type 28-bit Channel Link LVDS transmitter
Tensão de alimentação 3.3 V
Maximum Transmit Clock Frequency 66 MHz
Parallel Input Width 28 bits
Input Logic LVCMOS/LVTTL
LVDS Data Outputs 4 differential streams
LVDS Clock Outputs 1 differential stream
Total Differential Outputs 5 LVDS links
Data Strobe Edge Rising edge
Clock Architecture Phase-locked transmit clock
Encapsulamento 56-pin TSSOP
Tipo de montagem Surface mount
Temperatura de operação -40°C to +85°C
Interface Standard LVDS

Guia de Configuração de Pinos do DS90CR285MTD 56-pin tssop

Configuração de pinos para DS90CR285MTD (pacote 56-pin tssop). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.

Diagrama de pinagem do pacote 56-pin tssop para DS90CR285MTD

Nenhum dado detalhado de pinagem disponível para DS90CR285MTD.

Consulte a ficha técnica para a configuração completa dos pinos.

Aplicações típicas

DS90CR285MTD é adequado para 6 aplicaçãos: Industrial Flat-Panel Display Interfaces, Digital Imaging and Video Processing, Industrial Test and Measurement Equipment, Point-to-Point Communications Equipment, High-Speed Control and Data Acquisition, Embedded Parallel-to-LVDS Bridging.

📺

Industrial Flat-Panel Display Interfaces

The DS90CR285MTD fits industrial display links when a controller presents 28 parallel data bits and the display receiver accepts Channel Link LVDS signaling. Its 66 MHz rising-edge data-strobe rate supports serialized transfer over four LVDS data lanes, while a fifth lane carries the phase-locked clock. The 56-pin TSSOP package and -40°C to +85°C operating range suit temperature-controlled industrial equipment. Designers should match both data and clock lane pairs to the receiver, confirm the supported coupling method, and maintain controlled impedance through the PCB and connector.

📺

Digital Imaging and Video Processing

The Texas Instruments DS90CR285MTD is appropriate for digital imaging modules that generate a 28-bit parallel pixel or processed-video bus but require a compact differential interface to a remote receiver. It converts the parallel LVCMOS/LVTTL payload into four balanced LVDS data streams and supplies a separate phase-locked clock link. This reduces the number of high-speed conductors compared with carrying all data over a single-ended parallel bus. For video timing, preserve the rising-edge relationship among pixel data, control signals, and the transmitted clock, then validate receiver tolerance to the complete board and cable channel.

🔧

Industrial Test and Measurement Equipment

The DS90CR285MTD can connect a parallel acquisition or processing engine to an external test module through a balanced LVDS Channel Link. Its 28-bit input width suits high-throughput parallel data movement, and the 66 MHz rising-edge strobe supports deterministic transfer of each data cycle. Four data lanes plus a dedicated clock lane make the interface practical for instrument backplanes and compact controller cards. The implementation must maintain controlled differential impedance, provide the receiver-specified termination, and verify channel bandwidth and skew margins when long cables or connector transitions are involved.

🌐

Point-to-Point Communications Equipment

The Texas Instruments DS90CR285MTD is useful in communications equipment that must bridge a 28-bit parallel engine to a differential link. Instead of routing 28 single-ended data conductors over a long distance, the transmitter serializes the payload onto four LVDS pairs and adds a phase-locked clock pair. Balanced signaling improves noise immunity and reduces EMI sensitivity compared with a long single-ended bus. System engineers should choose receiver termination and coupling appropriate to the physical channel, route all five pairs consistently, and verify cable loss, connector geometry, and clock/data skew before production release.

🏭

High-Speed Control and Data Acquisition

The DS90CR285MTD can serve as the transmitting endpoint in a high-speed control or acquisition subsystem where a modular processor produces 28 parallel bits per transfer cycle. The 66 MHz rising-edge interface and dedicated LVDS clock provide a defined timing reference for the remote receiver, while five differential links reduce the physical channel width. This arrangement is useful between circuit cards, across a short cable, or within a controlled industrial enclosure. Design validation should include source timing margins, receiver setup and hold requirements, termination values, and channel performance under the expected load.

🧩

Embedded Parallel-to-LVDS Bridging

The DS90CR285MTD bridges a legacy parallel processing interface to a modern differential link when an embedded controller must communicate through a compact, noise-resistant connection. The device accepts 28 LVCMOS/LVTTL bits, performs the parallel-to-LVDS conversion at up to 66 MHz, and transmits the phase-locked clock separately from the data. Its 3.3 V operation aligns with many mixed-signal embedded designs, while the TSSOP package supports automated assembly. Confirm logic thresholds, reset or clocking requirements, and receiver protocol compatibility before treating the Channel Link as a generic video interface.

What is the DS90CR285MTD?
The DS90CR285MTD is a 28-bit Channel Link LVDS transmitter from Texas Instruments. According to the manufacturer product page, it operates from 3.3 V, accepts 28 parallel LVCMOS/LVTTL data bits, converts them into four differential LVDS data streams, and transmits a phase-locked clock over a fifth LVDS link. The device uses rising-edge data strobing, supports up to 66 MHz, and is packaged in a 56-pin TSSOP.
How many LVDS outputs does DS90CR285MTD provide?
The DS90CR285MTD provides five differential LVDS links in total. Four links carry the 28 parallel data bits, while the fifth link carries the phase-locked transmit clock. This arrangement follows the Channel Link architecture described by Texas Instruments and reduces the number of high-speed conductors required between the parallel logic source and the LVDS receiver.
What is the maximum clock frequency of DS90CR285MTD?
The DS90CR285MTD supports a maximum transmit clock frequency of 66 MHz. Texas Instruments describes the DS90CR285 as a rising-edge data-strobe LVDS transmitter. The clock is transmitted in parallel with the four data streams over a fifth differential link, allowing the receiving device to recover a timing reference associated with each transferred data cycle.
Where can I download the DS90CR285MTD datasheet?
The official DS90CR285 datasheet and product information are available through the Texas Instruments DS90CR285 product page at https://www.ti.com/product/DS90CR285. Use the manufacturer datasheet for the authoritative pin descriptions, recommended termination values, electrical characteristics, application circuit, and package drawings. The distributor listing for DS90CR285MTD also provides a direct link to technical documentation.
Where can I find the DS90CR285MTD pinout?
Use the pin-description table and package drawing in the Texas Instruments DS90CR285 datasheet for the authoritative 56-pin TSSOP pinout. The DS90CR285MTD is a surface-mount device with 28 parallel data inputs, differential LVDS data outputs, a differential clock output, supply pins, ground pins, and control or clock-related connections. Use the pin-description table when assigning PCB tracks and the package drawing to confirm physical orientation.
Is DS90CR285MTD compatible with 3.3 V LVCMOS logic?
Yes, the DS90CR285MTD is designed for a 3.3 V supply and accepts 28 parallel LVCMOS/LVTTL input bits. Texas Instruments identifies the device as a +3.3 V rising-edge data-strobe transmitter. Confirm the complete input voltage, output-voltage, and timing limits in the manufacturer datasheet for the specific source device, clock arrangement, and operating conditions used in the design.
What is the difference between DS90CR285MTD and DS90CR285MTD/NOPB?
Both parts identify the same Texas Instruments 28-bit, 66 MHz, 3.3 V LVDS transmitter in a 56-pin TSSOP package. The distinguishing ordering information concerns the device suffix and assembly or material designation rather than the core transmitter function. For a new PCB, confirm the exact ordering code, package marking, and production requirements before treating the two entries as equivalent.
Can DS90CR285MTD/NOPB replace DS90CR285MTD?
The DS90CR285MTD/NOPB is a close drop-in candidate for DS90CR285MTD because both are listed as Texas Instruments 28-bit Channel Link LVDS transmitters in a 56-pin TSSOP package. Before replacement, verify the exact ordering suffix, package dimensions, pinout, electrical characteristics, and assembly requirements in the manufacturer documentation. The NOPB designation identifies a different ordering variant, not a different interface architecture.
What can replace the DS90CR285MTD?
The closest documented drop-in replacement is DS90CR285MTD/NOPB because it retains the same 28-bit parallel input, four LVDS data outputs, fifth LVDS clock link, 3.3 V supply, 66 MHz clock rate, and 56-pin TSSOP package. No verified cross-brand pin-compatible substitute was established for this product. Treat any receiver-only part, such as a complementary DS90CR286-family device, as a different circuit function rather than a transmitter replacement.
Is DS90CR285MTD the same as DS90CR286AMTD/NOPB?
No. The DS90CR285MTD is a transmitter, while the DS90CR286 family represents the complementary Channel Link receiver function. Although both families are associated with 56-pin TSSOP interface devices, a transmitter and receiver cannot be substituted without changing the link architecture and signal flow. Choose DS90CR285MTD when parallel logic must be serialized onto LVDS differential outputs.
When should I choose DS90CR285MTD over another LVDS transmitter?
Choose DS90CR285MTD when the source device provides 28 parallel LVCMOS/LVTTL bits at up to a 66 MHz rising-edge clock and the destination expects four LVDS data lanes plus a separate phase-locked clock lane. Its 3.3 V supply and 56-pin TSSOP package suit conventional surface-mount boards. Select another interface only after matching lane count, clocking method, supply voltage, electrical timing, and connector termination.
Is DS90CR285MTD suitable for an industrial display interface?
The DS90CR285MTD is suitable for an industrial display interface when the display controller uses a compatible 28-bit parallel Channel Link input and supports a 66 MHz rising-edge strobe. Its -40°C to +85°C operating range covers many industrial environments. The system designer must still validate cable length, connector, AC or DC coupling, receiver termination, and signal-integrity margins for the completed link.
What are the key specifications of DS90CR285MTD engineers should know?
The key DS90CR285MTD specifications are a 3.3 V supply, 66 MHz maximum transmit clock, 28 LVCMOS/LVTTL input bits, four differential LVDS data outputs, one differential clock output, rising-edge strobing, and a 56-pin TSSOP package. According to the Texas Instruments product page, the transmitted clock is phase-locked to the parallel data. These parameters determine source-interface, clocking, PCB-routing, and receiver compatibility.
How should DS90CR285MTD LVDS pairs be routed on a PCB?
Route every DS90CR285MTD LVDS output as a continuous differential pair over a continuous reference plane. Keep intra-pair spacing and trace geometry consistent, avoid stubs and unnecessary layer transitions, and match the receiver's termination arrangement. Because the transmitter provides four data links and one clock link, preserve the clock lane as a controlled-impedance pair and confirm that PCB pair length and loss satisfy the receiver requirements.
How do I buy DS90CR285MTD and check price and lead time?
Use the Request a Quote form on this page to request current DS90CR285MTD pricing, stock status, lead time, and quantity availability. The DS90CR285MTD is listed as a 56-TSSOP Texas Instruments interface IC, but current commercial terms can vary with order quantity and supply status. Submit the target quantity, assembly requirements, and delivery location with the quote request.

Dados de referência de engenharia para DS90CR285MTD — comparação, orientação de projeto e informações de conformidade.

Guia de seleção

Choose DS90CR285MTD for a 3.3 V system whose source device supplies 28 parallel LVCMOS/LVTTL bits and requires four LVDS data channels plus a phase-locked clock channel at up to 66 MHz. Choose DS90CR285MTD/NOPB when its documented ordering suffix matches production, assembly, and procurement requirements while retaining the same 56-pin TSSOP interface and core ratings. Choose DS90CR285MTDX when that delivery-code variant is the approved configuration for the production line. Both listed alternatives preserve the 28-bit input, four LVDS data outputs, fifth clock output, 3.3 V supply, and 66 MHz clock rate. No cross-brand substitute or receiver-family device is recommended because a verified pin-compatible transmitter with matching electrical behavior was not established. Confirm timing, coupling, termination, and connector requirements with the receiver before final PCB release.

Comparação com alternativas

Parâmetro Este produto DS90CR285MTD/NOPB DS90CR285MTDX
Brand Texas Instruments Texas Instruments Texas Instruments
Package 56-pin TSSOP 56-pin TSSOP - same 56-pin TSSOP - same
Product Function 28-bit Channel Link LVDS transmitter 28-bit Channel Link LVDS transmitter 28-bit Channel Link LVDS transmitter
Supply Voltage 3.3 V 3.3 V 3.3 V
Maximum Transmit Clock Frequency 66 MHz 66 MHz 66 MHz
Parallel Input Width 28 bits 28 bits 28 bits
Input Logic LVCMOS/LVTTL LVCMOS/LVTTL LVCMOS/LVTTL
LVDS Data Outputs 4 differential streams 4 differential streams 4 differential streams
LVDS Clock Outputs 1 differential stream 1 differential stream 1 differential stream
Operating Temperature -40°C to +85°C -40°C to +85°C -40°C to +85°C

Principais diferenciais

  • Converts 28 parallel bits into four LVDS data lanes while providing a separate clock lane (vs DS90CR285MTD/NOPB)
  • Maintains the same 66 MHz rising-edge Channel Link timing as the MTDX ordering variant (vs DS90CR285MTDX)
  • Provides the same 3.3 V operation and 56-pin TSSOP footprint across identified ordering variants (vs DS90CR285MTD/NOPB)

Notas de projeto

Route the four LVDS data pairs and the dedicated clock pair as controlled-impedance differential nets over a continuous reference plane. Keep each pair's spacing and trace geometry consistent, avoid stubs and unnecessary layer changes, and preserve the clock pair as carefully as the data pairs. Match the physical PCB construction and connector geometry to the receiver's impedance requirements to reduce reflections and preserve clock-to-data timing margins.

Confirm the receiver's termination and coupling arrangement before finalizing the transmitter board. The DS90CR285MTD provides four differential data links and one phase-locked clock link, so incorrect termination on any pair can affect signal integrity or clock recovery. Use the manufacturer application information to select receiver-side termination and test the complete channel with realistic cable, connector, and receiver loading.

Do not treat DS90CR286-family receivers as direct replacements for DS90CR285 transmitters; they perform complementary link functions even though similar family members use a 56-pin TSSOP package. When substituting DS90CR285 ordering variants, verify the exact suffix, package drawing, pin names, assembly requirements, and lifecycle status. A shared footprint alone does not establish that two interface devices are electrically interchangeable.

Informações de conformidade

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Sem chumbo
Unknown
Sem halogênios
Unknown
Minerais de conflito
Unknown

The device is an industrial-temperature interface IC rather than an automotive-qualified product. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer product page or current material declaration.

Dados verificados em: 2026-11-10 — dados verificados e curados pela equipe de engenharia de componentes da XAIPART

Buscas relacionadas

ds90cr285mtd nopb DS90CR285MTD datasheet DS90CR285MTD pinout DS90CR285MTD datasheet pdf DS90CR285MTD replacement DS90CR285MTD equivalent DS90CR285MTD 66MHz LVDS DS90CR285MTD 56-TSSOP pinout DS90CR285MTD vs DS90CR286AMTD DS90CR285MTD display interface Texas Instruments DS90CR285MTD DS90CR285MTD price

Componentes & termos relacionados

Texas Instruments DS90CR285MTD DS90CR285MTD/NOPB DS90CR285MTDX DS90CR286AMTD/NOPB DS90CR285 DS90CR286 LVDS Low Voltage Differential Signaling Channel Link LVDS transmitter differential interface data transceiver semiconductor LVCMOS LVTTL parallel-to-serial interface phase-locked clock 28-bit parallel bus 66 MHz clock 3.3 V logic TSSOP-56 surface mount industrial electronics
RFQ de cotação rápida
Preencha todos os detalhes — nossa equipe de vendas responderá em até 24 horas
Part number Fabricante Encapsulamento QTY Preço-alvo Total
✓
Cotação enviada!

Responderemos seu e-mail em até 24 horas

1
RFQ enviada
2
Cotação recebida
3
Pedido realizado
4
Pagamento
5
Enviado
6
Entregue
Ver detalhes da RFQ