DS90CR285MTD - 28-Bit 66MHz LVDS Transmitter | Texas Instruments
Артикул: DS90CR285MTD ✓ АктивенDS90CR285MTD Обзор
An LVDS transmitter is a high-speed interface device that converts low-voltage complementary logic into balanced differential signals. LVDS belongs to the broader differential-interface and data-transceiver hierarchy, where low signal amplitude, common-mode rejection, and reduced electromagnetic interference support reliable point-to-point data transfer. DS90CR285 devices are commonly positioned between parallel digital logic and a high-speed LVDS link on displays, industrial controllers, and communications equipment.
The principal features include 28 parallel data inputs, four LVDS data outputs, one additional LVDS clock output, and a 66 MHz maximum parallel-clock frequency. The transmitted clock is phase-locked to the source data, allowing the receiving system to recover timing. The device also accepts a rising-edge data strobe and operates from a single 3.3 V supply. Its 56-pin TSSOP package provides a conventional surface-mount interface for systems using high-density parallel-to-differential signaling.
The transmitter architecture divides the 28-bit parallel payload into four differential data lanes and provides a separate clock lane. This arrangement limits the number of high-speed differential conductors required to carry the payload. Compared with single-ended parallel transmission, the balanced outputs improve noise immunity and can reduce connector and PCB signal-integrity problems when the receiver, termination network, trace geometry, and clock distribution are designed correctly.
Typical uses include digital display interfaces, flat-panel monitor backplane links, industrial imaging equipment, video-processing systems, test equipment, and embedded control systems that exchange parallel data over a short differential cable or board-level LVDS connection. The transmitter is also suitable where a source device has a 28-bit parallel bus but the destination requires a smaller number of low-voltage differential conductors.
PCB implementation should treat the LVDS outputs as controlled-impedance differential pairs. Route each pair continuously over a solid reference plane, keep the spacing within the pair consistent, and place the receiver-side termination close to the receiver. Avoid adding test pads or routing discontinuities that create impedance mismatches, and verify AC-coupled or DC-coupled connectivity against the receiver's input requirements.
This product record combines the device's key interface characteristics, package information, sourcing guidance, compatible ordering variants, and practical implementation considerations. It helps engineers identify the correct Texas Instruments LVDS transmitter, compare its electrically identical ordering options, and plan a robust 28-bit parallel-to-LVDS interface before committing a PCB layout.
Аналоги без доработки для DS90CR285MTD — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с DS90CR285MTD (тот же форм-фактор и посадочное место) — отличается по Package, Product Type, Supply Voltage, Packaging.
DS90CR285MTD/NOPB
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
DS90CR285MTDX
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
DS90CR285MTD Характеристики
| Product Type | 28-bit Channel Link LVDS transmitter |
| Напряжение питания | 3.3 V |
| Maximum Transmit Clock Frequency | 66 MHz |
| Parallel Input Width | 28 bits |
| Input Logic | LVCMOS/LVTTL |
| LVDS Data Outputs | 4 differential streams |
| LVDS Clock Outputs | 1 differential stream |
| Total Differential Outputs | 5 LVDS links |
| Data Strobe Edge | Rising edge |
| Clock Architecture | Phase-locked transmit clock |
| Корпус | 56-pin TSSOP |
| Тип монтажа | Surface mount |
| Рабочая температура | -40°C to +85°C |
| Interface Standard | LVDS |
Руководство по цоколевке DS90CR285MTD в корпусе 56-pin tssop
Цоколевка для DS90CR285MTD (корпус 56-pin tssop). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для DS90CR285MTD.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
DS90CR285MTD подходит для 6 применениеs: Industrial Flat-Panel Display Interfaces, Digital Imaging and Video Processing, Industrial Test and Measurement Equipment, Point-to-Point Communications Equipment, High-Speed Control and Data Acquisition, Embedded Parallel-to-LVDS Bridging.
Industrial Flat-Panel Display Interfaces
The DS90CR285MTD fits industrial display links when a controller presents 28 parallel data bits and the display receiver accepts Channel Link LVDS signaling. Its 66 MHz rising-edge data-strobe rate supports serialized transfer over four LVDS data lanes, while a fifth lane carries the phase-locked clock. The 56-pin TSSOP package and -40°C to +85°C operating range suit temperature-controlled industrial equipment. Designers should match both data and clock lane pairs to the receiver, confirm the supported coupling method, and maintain controlled impedance through the PCB and connector.
Рекомендуется
Digital Imaging and Video Processing
The Texas Instruments DS90CR285MTD is appropriate for digital imaging modules that generate a 28-bit parallel pixel or processed-video bus but require a compact differential interface to a remote receiver. It converts the parallel LVCMOS/LVTTL payload into four balanced LVDS data streams and supplies a separate phase-locked clock link. This reduces the number of high-speed conductors compared with carrying all data over a single-ended parallel bus. For video timing, preserve the rising-edge relationship among pixel data, control signals, and the transmitted clock, then validate receiver tolerance to the complete board and cable channel.
Рекомендуется
Industrial Test and Measurement Equipment
The DS90CR285MTD can connect a parallel acquisition or processing engine to an external test module through a balanced LVDS Channel Link. Its 28-bit input width suits high-throughput parallel data movement, and the 66 MHz rising-edge strobe supports deterministic transfer of each data cycle. Four data lanes plus a dedicated clock lane make the interface practical for instrument backplanes and compact controller cards. The implementation must maintain controlled differential impedance, provide the receiver-specified termination, and verify channel bandwidth and skew margins when long cables or connector transitions are involved.
Рекомендуется
Point-to-Point Communications Equipment
The Texas Instruments DS90CR285MTD is useful in communications equipment that must bridge a 28-bit parallel engine to a differential link. Instead of routing 28 single-ended data conductors over a long distance, the transmitter serializes the payload onto four LVDS pairs and adds a phase-locked clock pair. Balanced signaling improves noise immunity and reduces EMI sensitivity compared with a long single-ended bus. System engineers should choose receiver termination and coupling appropriate to the physical channel, route all five pairs consistently, and verify cable loss, connector geometry, and clock/data skew before production release.
Рекомендуется
High-Speed Control and Data Acquisition
The DS90CR285MTD can serve as the transmitting endpoint in a high-speed control or acquisition subsystem where a modular processor produces 28 parallel bits per transfer cycle. The 66 MHz rising-edge interface and dedicated LVDS clock provide a defined timing reference for the remote receiver, while five differential links reduce the physical channel width. This arrangement is useful between circuit cards, across a short cable, or within a controlled industrial enclosure. Design validation should include source timing margins, receiver setup and hold requirements, termination values, and channel performance under the expected load.
Рекомендуется
Embedded Parallel-to-LVDS Bridging
The DS90CR285MTD bridges a legacy parallel processing interface to a modern differential link when an embedded controller must communicate through a compact, noise-resistant connection. The device accepts 28 LVCMOS/LVTTL bits, performs the parallel-to-LVDS conversion at up to 66 MHz, and transmits the phase-locked clock separately from the data. Its 3.3 V operation aligns with many mixed-signal embedded designs, while the TSSOP package supports automated assembly. Confirm logic thresholds, reset or clocking requirements, and receiver protocol compatibility before treating the Channel Link as a generic video interface.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для DS90CR285MTD — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | DS90CR285MTD/NOPB | DS90CR285MTDX |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 56-pin TSSOP | 56-pin TSSOP - same | 56-pin TSSOP - same |
| Product Function | 28-bit Channel Link LVDS transmitter | 28-bit Channel Link LVDS transmitter | 28-bit Channel Link LVDS transmitter |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V |
| Maximum Transmit Clock Frequency | 66 MHz | 66 MHz | 66 MHz |
| Parallel Input Width | 28 bits | 28 bits | 28 bits |
| Input Logic | LVCMOS/LVTTL | LVCMOS/LVTTL | LVCMOS/LVTTL |
| LVDS Data Outputs | 4 differential streams | 4 differential streams | 4 differential streams |
| LVDS Clock Outputs | 1 differential stream | 1 differential stream | 1 differential stream |
| Operating Temperature | -40°C to +85°C | -40°C to +85°C | -40°C to +85°C |
Ключевые отличия
- Converts 28 parallel bits into four LVDS data lanes while providing a separate clock lane (против DS90CR285MTD/NOPB)
- Maintains the same 66 MHz rising-edge Channel Link timing as the MTDX ordering variant (против DS90CR285MTDX)
- Provides the same 3.3 V operation and 56-pin TSSOP footprint across identified ordering variants (против DS90CR285MTD/NOPB)
Заметки по проектированию
Route the four LVDS data pairs and the dedicated clock pair as controlled-impedance differential nets over a continuous reference plane. Keep each pair's spacing and trace geometry consistent, avoid stubs and unnecessary layer changes, and preserve the clock pair as carefully as the data pairs. Match the physical PCB construction and connector geometry to the receiver's impedance requirements to reduce reflections and preserve clock-to-data timing margins.
Confirm the receiver's termination and coupling arrangement before finalizing the transmitter board. The DS90CR285MTD provides four differential data links and one phase-locked clock link, so incorrect termination on any pair can affect signal integrity or clock recovery. Use the manufacturer application information to select receiver-side termination and test the complete channel with realistic cable, connector, and receiver loading.
Do not treat DS90CR286-family receivers as direct replacements for DS90CR285 transmitters; they perform complementary link functions even though similar family members use a 56-pin TSSOP package. When substituting DS90CR285 ordering variants, verify the exact suffix, package drawing, pin names, assembly requirements, and lifecycle status. A shared footprint alone does not establish that two interface devices are electrically interchangeable.
Информация о соответствии
The device is an industrial-temperature interface IC rather than an automotive-qualified product. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer product page or current material declaration.