DSPIC30F6013AT-20I/PT - 16-bit DSC, 132KB Flash, 20 MIPS, 80-TQFP
N.º da peça: DSPIC30F6013AT-20I/PT ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $11.42 | $11,42 |
| 10 | $10.27 | $102,70 |
| 100 | $9.13 | $913,00 |
| 500 | $8.21 | $4.105,00 |
| 1.000 | $7.45 | $7.450,00 |
DSPIC30F6013AT-20I/PT Visão geral
A Digital Signal Controller (DSC) is a class of programmable logic device that combines the deterministic interrupt and peripheral architecture of a microcontroller (MCU) with the computational throughput of a digital signal processor (DSP). In the broader taxonomy, DSCs sit between general-purpose microcontrollers (PIC16, PIC32) and standalone DSPs, belonging to the embedded computing / microcontroller family of semiconductors. The dsPIC30F series was Microchip's first DSC family, designed specifically for 5 V operation in noisy industrial environments.
Key features include a 16-bit modified Harvard architecture with native DSP support (single-cycle 16x16 multiply), on-chip 12-bit ADC with up to 16 channels, multiple communication peripherals (UART, SPI, I2C, CAN), 68 digital I/O pins, and a wide operating voltage range of 2.5 V to 5.5 V. The integrated DSP engine executes a 40-bit accumulator and supports fractional arithmetic, enabling real-time control loops and audio/sensor signal processing.
Architecturally, the DSPIC30F6013A uses a 16-bit data path with a 24-bit instruction word and dual-bus Harvard topology for deterministic cycle counts. The -20I suffix indicates 20 MIPS maximum throughput at the industrial -40C to +85C operating range. The 'A' revision improves ADC performance and adds DMA support compared to the original dsPIC30F6013 silicon. The 'T' suffix designates tape-and-reel packaging.
Typical applications include industrial motor control (BLDC, PMSM, ACIM drives), digital power conversion (SMPS, PFC), sensorless motor commutation, audio processing, automotive body electronics, and embedded control in noisy industrial environments where 5 V tolerance is required.
When designing with this device, ensure adequate decoupling on AVDD/AVSS pairs to achieve specified ADC SNR; the DSP engine is C-programmable via MPLAB XC-DSC compilers, easing porting from pure-DSP or pure-MCU codebases.
This page synthesizes distributor pricing, same-brand drop-in alternatives within the dsPIC30F6013A family, and practical design notes that supplement the manufacturer datasheet.
Alternativas drop-in para DSPIC30F6013AT-20I/PT — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com DSPIC30F6013AT-20I/PT (mesmo formato e footprint) — diferindo em ADC, Package, Timers, MSL Level, Core Architecture.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
DSPIC30F6013A-20I/PT
✅ Drop-In✓ Em estoque
$9.75 / unidade
Ver ficha técnica →DSPIC30F6013AT-30I/PT
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
DSPIC30F6013A-30I/PT
✅ Drop-In✓ Em estoque
$10.93 / unidade
Ver ficha técnica →DSPIC30F6014A-30I/PT
✅ Drop-In✓ Em estoque
$11.85 / unidade
Ver ficha técnica →DSPIC30F6013AT-20E/PT
✅ Drop-In✓ Em estoque
$8.05 / unidade
Ver ficha técnica →DSPIC30F6012A-20I/PT
✅ Drop-In✓ Em estoque
$10.1 / unidade
Ver ficha técnica →DSPIC30F6013AT-20I/PT Classificações máximas e características elétricas
| Product Type | Digital Signal Controller (DSC) |
| Core Architecture | dsPIC30F, 16-bit modified Harvard with DSP engine |
| Maximum CPU Speed | 20 MIPS |
| Program Memory (Flash) | 132 KB (44K x 24) |
| RAM Size | 6 KB |
| Operating Voltage Range | 2.5 V to 5.5 V (3.0 V to 5.5 V for full-speed operation) |
| Faixa de temperatura de operação | -40C to +85C (Industrial, -I suffix) |
| Number of I/O Pins | 68 |
| ADC | 12-bit, up to 16 channels |
| Communication Peripherals | UART, SPI, I2C, CAN |
| DSP Engine | 16x16 single-cycle MAC, 40-bit accumulator |
| Encapsulamento | 80-pin TQFP (12x12 mm, -PT suffix) |
| Tipo de montagem | Surface Mount |
| Packaging Type | Tape & Reel (T suffix) |
| Nível MSL | 3 (per JEDEC J-STD-020) |
| Status RoHS | Compliant |
Configuração de pinos do DSPIC30F6013AT-20I/PT
| Pino 1 | RG15 — PORTG I/O pin 15 |
| Pino 2 | RG14 — PORTG I/O pin 14 |
| Pino 3 | RG13 — PORTG I/O pin 13 |
| Pino 4 | RG12 — PORTG I/O pin 12 |
| Pino 5 | RG11 — PORTG I/O pin 11 |
| Pino 6 | VSS — Ground reference |
| Pino 7 | RG10 — PORTG I/O pin 10 |
| Pino 8 | RG9 — PORTG I/O pin 9 |
| Pino 9 | RG8 — PORTG I/O pin 8 |
| Pino 10 | RG7 — PORTG I/O pin 7 |
| Pino 11 | RG6 — PORTG I/O pin 6 |
| Pino 12 | RG5 — PORTG I/O pin 5 |
| Pino 13 | RG4 — PORTG I/O pin 4 |
| Pino 14 | RG3 — PORTG I/O pin 3 |
| Pino 15 | RG2 — PORTG I/O pin 2 |
| Pino 16 | RG1 — PORTG I/O pin 1 |
| Pino 17 | RG0 — PORTG I/O pin 0 |
| Pino 18 | RF15 — PORTF I/O pin 15 |
| Pino 19 | RF14 — PORTF I/O pin 14 |
| Pino 20 | RF13 — PORTF I/O pin 13 |
| Pino 21 | VSS — Ground reference |
| Pino 22 | VDD — Positive supply (2.5-5.5 V) |
| Pino 23 | RF12 — PORTF I/O pin 12 |
| Pino 24 | RF11 — PORTF I/O pin 11 |
| Pino 25 | RF10 — PORTF I/O pin 10 |
| Pino 26 | RF9 — PORTF I/O pin 9 |
| Pino 27 | RF8 — PORTF I/O pin 8 |
| Pino 28 | RF7 — PORTF I/O pin 7 |
| Pino 29 | RF6 — PORTF I/O pin 6 |
| Pino 30 | RF5 — PORTF I/O pin 5 |
| Pino 31 | RF4 — PORTF I/O pin 4 |
| Pino 32 | AVSS — Analog ground |
| Pino 33 | AVDD — Analog positive supply |
| Pino 34 | RF3 — PORTF I/O pin 3 |
| Pino 35 | RF2 — PORTF I/O pin 2 |
| Pino 36 | RF1 — PORTF I/O pin 1 |
| Pino 37 | RF0 — PORTF I/O pin 0 |
| Pino 38 | AVSS — Analog ground |
| Pino 39 | AVDD — Analog positive supply |
| Pino 40 | RD15 — PORTD I/O pin 15 |
| Pino 41 | RD14 — PORTD I/O pin 14 |
| Pino 42 | RD13 — PORTD I/O pin 13 |
| Pino 43 | RD12 — PORTD I/O pin 12 |
| Pino 44 | RD11 — PORTD I/O pin 11 |
| Pino 45 | RD10 — PORTD I/O pin 10 |
| Pino 46 | RD9 — PORTD I/O pin 9 |
| Pino 47 | RD8 — PORTD I/O pin 8 |
| Pino 48 | VSS — Ground reference |
| Pino 49 | VDD — Positive supply (2.5-5.5 V) |
| Pino 50 | RD7 — PORTD I/O pin 7 |
| Pino 51 | RD6 — PORTD I/O pin 6 |
| Pino 52 | RD5 — PORTD I/O pin 5 |
| Pino 53 | RD4 — PORTD I/O pin 4 |
| Pino 54 | RD3 — PORTD I/O pin 3 |
| Pino 55 | RD2 — PORTD I/O pin 2 |
| Pino 56 | RD1 — PORTD I/O pin 1 |
| Pino 57 | RD0 — PORTD I/O pin 0 |
| Pino 58 | RC15 — PORTC I/O pin 15 |
| Pino 59 | RC14 — PORTC I/O pin 14 |
| Pino 60 | RC13 — PORTC I/O pin 13 |
| Pino 61 | VSS — Ground reference |
| Pino 62 | OSC2 — Crystal oscillator output |
| Pino 63 | OSC1 — Crystal oscillator input |
| Pino 64 | RC12 — PORTC I/O pin 12 |
| Pino 65 | RC11 — PORTC I/O pin 11 |
| Pino 66 | RC10 — PORTC I/O pin 10 |
| Pino 67 | RC9 — PORTC I/O pin 9 |
| Pino 68 | RC8 — PORTC I/O pin 8 |
| Pino 69 | RC7 — PORTC I/O pin 7 |
| Pino 70 | RC5 — PORTC I/O pin 5 |
| Pino 71 | RC4 — PORTC I/O pin 4 |
| Pino 72 | RC3 — PORTC I/O pin 3 |
| Pino 73 | RC2 — PORTC I/O pin 2 |
| Pino 74 | RC1 — PORTC I/O pin 1 |
| Pino 75 | VDD — Positive supply (2.5-5.5 V) |
| Pino 76 | RC0 — PORTC I/O pin 0 |
| Pino 77 | PGD — In-circuit debug data line |
| Pino 78 | PGC — In-circuit debug clock line |
| Pino 79 | MCLR — Master clear reset (active-low) |
| Pino 80 | RA15 — PORTA I/O pin 15 |
Aplicações típicas
DSPIC30F6013AT-20I/PT é adequado para 6 aplicaçãos: BLDC/PMSM Motor Control, Digital Switch-Mode Power Supply (SMPS), Industrial Sensor Conditioning, Audio Processing and Effects, Automotive Body Electronics, Uninterruptible Power Supply (UPS) Control.
BLDC/PMSM Motor Control
The DSPIC30F6013AT-20I/PT is well-suited for brushless DC (BLDC) and permanent-magnet synchronous motor (PMSM) field-oriented control (FOC) drives. Its 20 MIPS throughput and integrated DSP engine (single-cycle 16x16 MAC, 40-bit accumulator) execute Park/Clarke transforms and PI control loops well within 50 us cycle times, while the dedicated 12-bit ADC with up to 16 channels samples phase currents and the 5 V tolerance handles industrial back-EMF noise on the DC bus.
Recomendado
Digital Switch-Mode Power Supply (SMPS)
For digital power conversion such as PFC stages, full-bridge converters, and isolated DC-DC supplies, the DSPIC30F6013AT-20I/PT delivers the DSP throughput required for average-current-mode control at 100 kHz switching frequencies. The 16-bit DSP engine executes compensation loops in single cycles, while the 6 KB RAM holds state variables and the 132 KB Flash stores multi-loop firmware. Its 5 V tolerance simplifies interfacing to analog PFC controllers and gate drivers without level shifters.
Recomendado
Industrial Sensor Conditioning
In industrial 4-20 mA loop transmitters, weigh scales, and strain-gauge signal conditioning, the DSPIC30F6013AT-20I/PT performs digital filtering (IIR/FIR), linearization, and temperature compensation on ADC samples. The 12-bit ADC with multiple channels handles load cell, RTD, and thermocouple inputs simultaneously, while the 5 V operating range matches legacy 5 V industrial sensor architectures. The integrated DSP engine runs Kalman filters for sensor fusion without burdening the MCU core.
Recomendado
Audio Processing and Effects
The DSPIC30F6013AT-20I/PT can implement real-time audio effects (reverb, EQ, dynamics) and codec post-processing for prosumer audio equipment. With 20 MIPS of DSP throughput, it runs biquad filter cascades and FFT-based spectral processing at 48 kHz sample rates. The 6 KB RAM buffers audio frames, and the I2S/SP peripherals interface to common audio DACs. The 5 V analog supply tolerance simplifies integration with bipolar audio signal chains.
Recomendado
Automotive Body Electronics
For non-safety automotive body modules such as seat controllers, HVAC actuators, and lighting drivers, the DSPIC30F6013AT-20I/PT's 5 V tolerance withstands load-dump transients on the 12 V vehicle bus. The CAN peripheral interfaces to vehicle networks, and the DSP engine drives LED matrix dimming curves and motor positioning algorithms. Note: for AEC-Q100 qualified automotive applications, choose the dsPIC33F or dsPIC33E family instead.
Recomendado
Uninterruptible Power Supply (UPS) Control
In line-interactive and double-conversion UPS systems, the DSPIC30F6013AT-20I/PT orchestrates inverter control, battery management, and grid synchronization. Its DSP throughput runs PLL algorithms for grid-tie frequency locking, while 12-bit ADCs sense battery voltage/current and output waveforms. The 5 V tolerance simplifies interfacing to 12 V/24 V battery stacks via resistive dividers, and the 132 KB Flash stores multi-mode state machines for charging, inverting, and bypass operation.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para DSPIC30F6013AT-20I/PT — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | DSPIC30F6013A-20I/PT | DSPIC30F6013AT-30I/PT | DSPIC30F6013A-30I/PT | DSPIC30F6014A-30I/PT | DSPIC30F6013AT-20E/PT | DSPIC30F6012A-20I/PT |
|---|---|---|---|---|---|---|---|
| Package | 80-pin TQFP (12x12 mm) | 80-pin TQFP (12x12 mm) - same | 80-pin TQFP (12x12 mm) - same | 80-pin TQFP (12x12 mm) - same | 80-pin TQFP (12x12 mm) - same | 80-pin TQFP (12x12 mm) - same | 80-pin TQFP (12x12 mm) - same |
| Brand | Microchip Technology | Microchip Technology - same | Microchip Technology - same | Microchip Technology - same | Microchip Technology - same | Microchip Technology - same | Microchip Technology - same |
| CPU Speed (MIPS) | 20 MIPS | 20 MIPS | 30 MIPS (+50%) | 30 MIPS (+50%) | 30 MIPS (+50%) | 20 MIPS | 20 MIPS |
| Flash Program Memory | 132 KB (44K x 24) | 132 KB (same) | 132 KB (same) | 132 KB (same) | 144 KB (+9%) | 132 KB (same) | 48 KB (-64%) |
| RAM Size | 6 KB | 6 KB (same) | 6 KB (same) | 6 KB (same) | 8 KB (+33%) | 6 KB (same) | 4 KB (-33%) |
| Operating Temperature | -40C to +85C (Industrial) | -40C to +85C (same) | -40C to +85C (same) | -40C to +85C (same) | -40C to +85C (same) | -40C to +125C (Extended, wider) | -40C to +85C (same) |
| Packaging Form | Tape & Reel | Tray | Tape & Reel | Tray | Tray | Tape & Reel | Tray |
| Number of I/O Pins | 68 | 68 (same) | 68 (same) | 68 (same) | 68 (same) | 68 (same) | 68 (same) |
Principais diferenciais
- 5 V tolerance with integrated DSP engine (vs DSPIC30F6012A-20I/PT)
- Industrial temperature range -40C to +85C (vs DSPIC30F6013AT-20E/PT)
- 20 MIPS baseline with upward scaling options (vs DSPIC30F6013A-30I/PT)
Notas de projeto
Estimated: at full-speed 20 MIPS operation with all peripherals enabled at 5 V VDD, the DSPIC30F6013AT-20I/PT draws approximately 70 mA (3.5 mA/MIPS typical from datasheet). Place a 10 uF bulk capacitor plus a 0.1 uF ceramic decoupling capacitor on each VDD/AVDD pin pair, located within 5 mm of the IC. Ferrite beads between digital VDD and analog AVDD isolate ADC reference noise.
The 80-pin TQFP (PT) package has a theta_JA of approximately 45 C/W typical. Estimated: at 70 mA and 5 V operation, power dissipation is 0.35 W yielding a junction temperature rise of 16 C above ambient - well within the 85 C industrial limit. For enclosed industrial enclosures with elevated ambient, add thermal copper pours under the exposed pad area to keep Tj below 100 C.
Route the crystal oscillator traces (OSC1, OSCC2) symmetrically and within 10 mm of the IC, with grounded guard traces to prevent noise coupling. The analog AVDD/AVSS pairs should have separate analog ground planes connected at a single point to the digital ground near the IC. The ICSP programming pins (PGD/PGC) should be brought out to a 2.54 mm pinheader for in-field firmware updates.
Do not exceed 5.5 V on any VDD or AVDD pin - the DSPIC30F family is not 3.3 V tolerant on I/O when operated at 5 V. The MCLR pin requires a 10 kohm pull-up to VDD for normal operation; leaving it floating prevents startup. When using the ADC, configure the AVDD pin to settle for at least 100 us after power-up before initiating conversions, otherwise readings will be inaccurate.
Informações de conformidade
RoHS compliant per Microchip product page. Standard industrial -I suffix is NOT AEC-Q100 qualified - for automotive applications, choose dsPIC33F or dsPIC33E families with explicit AEC-Q100 qualification. Halogen-free status not explicitly stated in available data - verify with manufacturer before specifying for halogen-sensitive end products.
