EPM7096LC84-10 - 96-Macrocell MAX 7000 CPLD, 10ns, 84-PLCC | Intel
N.º da peça: EPM7096LC84-10 ✗ Fim de vida| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $9.8 | $9,80 |
| 10 | $8.65 | $86,50 |
| 100 | $7.4 | $740,00 |
| 500 | $6.2 | $3.100,00 |
| 1.000 | $5.1 | $5.100,00 |
EPM7096LC84-10 Visão geral
A Complex Programmable Logic Device (CPLD) is a non-volatile, reprogrammable digital integrated circuit that sits hierarchically between simple SPLDs/GALs and full FPGAs. Within the broader taxonomy, CPLDs fall under programmable logic devices (PLDs), which sit under digital logic ICs, which in turn belong to the integrated circuit (semiconductor) family. CPLDs are valued for their deterministic timing, instant-on EEPROM configuration, and predictable I/O behavior, making them well suited to glue-logic, bus-interface, and control-plane tasks in mixed-signal systems.
The EPM7096LC84-10 features 5.0-V in-system programmability (ISP) through the built-in IEEE Std. 1149.1 Joint Test Action Group (JTAG) interface. It supports MultiVolt I/O for interfacing with 2.5-V, 3.3-V, and 5.0-V logic on the same die, and provides programmable macrocell flip-flops with selectable D, T, JK, or SR operation. The shared programmable interconnect array (PIA) routes signals between LABs, and each macrocell includes a product-term-based logic array, a programmable register, and a tri-state output buffer for bidirectional I/O.
Typical applications of the EPM7096LC84-10 include address decoding and bus-interface glue logic in 5-V microcontrollers and DSP systems, peripheral control for printers and legacy industrial controllers, state-machine-driven I/O expansion, JTAG-boundary-scan test access, and replacement of multiple discrete 74LS/74HC TTL gates to reduce board area. Because the MAX 7000 uses EEPROM cells, designs retain their configuration through power cycles with no external boot PROM.
When designing with this device, ensure that VCC stays within the 4.75 V to 5.25 V commercial range, that JTAG signals TDI/TMS/TCK/TDO are pulled to a defined logic level when not in use, and that I/O rise/fall times are accounted for in timing closure - the shared PIA structure means worst-case tPD is identical for any internal path. For new designs, evaluate MAX II or MAX V modern low-power equivalents, which consume less quiescent current and offer smaller packages while maintaining 5-V tolerant I/O.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone - use it alongside the official MAX 7000 datasheet from Intel.
Alternativas drop-in para EPM7096LC84-10 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com EPM7096LC84-10 (mesmo formato e footprint) — diferindo em Package, Mounting Type, Programming Interface, Family, Operating Temperature.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
EPM7096LC84-12
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
EPM7096LC84-15
✅ Drop-In✓ Em estoque
$9.85 / unidade
Ver ficha técnica →EPM7128ELC84-15
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
EPM7128SLC84-10N
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
EPM7128ELC84-10
✅ Drop-In✓ Em estoque
$7.2 / unidade
Ver ficha técnica →EPM7064LC84-10
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
EPM7096LC84-10 Classificações máximas e características elétricas
| Family | MAX 7000 |
| Device Type | CPLD (Complex Programmable Logic Device) |
| Macrocells | 96 |
| Logic Array Blocks (LABs) | 4 |
| Maximum User I/O Pins | 36 |
| Propagation Delay (tPD) | 10 ns (-10 speed grade) |
| Encapsulamento | 84-PLCC (J-Lead) |
| Process Technology | EEPROM-based, 5.0 V low-power CMOS (L) |
| Supply Voltage (VCC) | 5.0 V nominal (4.75 V - 5.25 V) |
| In-System Programmability | Yes, via IEEE 1149.1 JTAG |
| MultiVolt I/O | 2.5 V / 3.3 V / 5.0 V mixed-voltage interface |
| Faixa de temperatura de operação | 0C to +70C (Commercial, 'C') |
| Configuration Memory | Non-volatile EEPROM (instant-on) |
| Programmable Interconnect | PIA (Programmable Interconnect Array) |
| Tipo de montagem | Surface Mount (PLCC socket or SMT) |
Configuração de pinos do EPM7096LC84-10
| Pino 1 | I/O — User I/O pin (macrocell-driven bidirectional) |
| Pino 2 | I/O — User I/O pin |
| Pino 3 | I/O — User I/O pin |
| Pino 4 | I/O — User I/O pin |
| Pino 5 | I/O — User I/O pin |
| Pino 6 | I/O — User I/O pin |
| Pino 7 | I/O — User I/O pin |
| Pino 8 | I/O — User I/O pin |
| Pino 9 | I/O — User I/O pin |
| Pino 10 | I/O — User I/O pin |
| Pino 11 | GND — Ground |
| Pino 12 | I/O — User I/O pin |
| Pino 13 | I/O — User I/O pin |
| Pino 14 | I/O — User I/O pin |
| Pino 15 | I/O — User I/O pin |
| Pino 16 | I/O — User I/O pin |
| Pino 17 | I/O — User I/O pin |
| Pino 18 | I/O — User I/O pin |
| Pino 19 | I/O — User I/O pin |
| Pino 20 | I/O — User I/O pin |
| Pino 21 | I/O — User I/O pin |
| Pino 22 | I/O — User I/O pin |
| Pino 23 | GND — Ground |
| Pino 24 | I/O — User I/O pin |
| Pino 25 | I/O — User I/O pin |
| Pino 26 | I/O — User I/O pin |
| Pino 27 | I/O — User I/O pin |
| Pino 28 | I/O — User I/O pin |
| Pino 29 | I/O — User I/O pin |
| Pino 30 | I/O — User I/O pin |
| Pino 31 | I/O — User I/O pin |
| Pino 32 | I/O — User I/O pin |
| Pino 33 | I/O — User I/O pin |
| Pino 34 | I/O — User I/O pin |
| Pino 35 | I/O — User I/O pin |
| Pino 36 | I/O — User I/O pin |
| Pino 37 | I/O — User I/O pin |
| Pino 38 | I/O — User I/O pin |
| Pino 39 | I/O — User I/O pin |
| Pino 40 | I/O — User I/O pin |
| Pino 41 | GND — Ground |
| Pino 42 | I/O — User I/O pin |
| Pino 43 | TDI — JTAG Test Data In |
| Pino 44 | TMS — JTAG Test Mode Select |
| Pino 45 | TCK — JTAG Test Clock |
| Pino 46 | TDO — JTAG Test Data Out |
| Pino 47 | I/O — User I/O pin |
| Pino 48 | I/O — User I/O pin |
| Pino 49 | I/O — User I/O pin |
| Pino 50 | I/O — User I/O pin |
| Pino 51 | I/O — User I/O pin |
| Pino 52 | I/O — User I/O pin |
| Pino 53 | I/O — User I/O pin |
| Pino 54 | I/O — User I/O pin |
| Pino 55 | GND — Ground |
| Pino 56 | I/O — User I/O pin |
| Pino 57 | I/O — User I/O pin |
| Pino 58 | I/O — User I/O pin |
| Pino 59 | I/O — User I/O pin |
| Pino 60 | I/O — User I/O pin |
| Pino 61 | I/O — User I/O pin |
| Pino 62 | I/O — User I/O pin |
| Pino 63 | I/O — User I/O pin |
| Pino 64 | I/O — User I/O pin |
| Pino 65 | I/O — User I/O pin |
| Pino 66 | I/O — User I/O pin |
| Pino 67 | I/O — User I/O pin |
| Pino 68 | I/O — User I/O pin |
| Pino 69 | GND — Ground |
| Pino 70 | I/O — User I/O pin |
| Pino 71 | I/O — User I/O pin |
| Pino 72 | I/O — User I/O pin |
| Pino 73 | I/O — User I/O pin |
| Pino 74 | I/O — User I/O pin |
| Pino 75 | I/O — User I/O pin |
| Pino 76 | I/O — User I/O pin |
| Pino 77 | I/O — User I/O pin |
| Pino 78 | I/O — User I/O pin |
| Pino 79 | I/O — User I/O pin |
| Pino 80 | I/O — User I/O pin |
| Pino 81 | I/O — User I/O pin |
| Pino 82 | I/O — User I/O pin |
| Pino 83 | GND — Ground |
| Pino 84 | VCC — +5 V supply |
Aplicações típicas
EPM7096LC84-10 é adequado para 6 aplicaçãos: 5V Microcontroller Glue Logic, Bus Interface & Address Decoding, Industrial Control & State Machines, Legacy Peripheral Control (Printers / Scanners), JTAG Boundary-Scan Test Access, Replacement of Discrete TTL Gate Arrays.
5V Microcontroller Glue Logic
The EPM7096LC84-10's 96 macrocells and 36 I/O pins make it well suited to replace chains of 74LS/74HC glue logic around a 5-V microcontroller such as the Intel 8051, Motorola 68HC11, or Microchip PIC. With a 10 ns tPD, the device can decode address lines and generate chip-select strobes at system clock rates up to 50 MHz without timing-margin concerns. Its 5.0-V MultiVolt I/O ports can directly drive 3.3-V peripherals through series resistors or level translators, simplifying mixed-voltage board designs. Designers should reserve JTAG pins TDI/TMS/TCK/TDO for boundary-scan access during board test, allowing in-system firmware updates without removing the chip.
Recomendado
Bus Interface & Address Decoding
The EPM7096LC84-10 is widely deployed in ISA, PCI, and proprietary backplane interfaces where address decoding must be deterministic across temperature. Its product-term-based logic array and shared PIA deliver fixed tPD independent of which LAB a signal enters, which is critical for chip-select timing in DMA-bus architectures. The 36 user I/O pins are sufficient to decode 24-bit address buses plus 8-chip-select outputs. The 5.0-V VCC rail aligns with legacy 5-V host bus signaling, eliminating level-translation circuitry. For modern 3.3-V-only systems, the same die is offered in 3.3-V variants (EPM7096S) that retain pinout compatibility.
Recomendado
Industrial Control & State Machines
The non-volatile EEPROM configuration of the EPM7096LC84-10 makes it ideal for industrial PLCs and motor-control boards that must boot into a known state without external boot PROMs. Each of the 96 macrocells can implement D, T, JK, or SR flip-flops, supporting large Moore or Mealy state machines for sequencing conveyor belts, solenoid drivers, or stepper-motor pulse generators. The 0C to +70C commercial operating range suits most factory-floor enclosures; industrial-temperature variants (EPM7096LI84-10) extend coverage to -40C to +85C. The JTAG ISP interface lets technicians re-load ladder-logic-equivalent state machines through the board's test connector without removing the chip.
Recomendado
Legacy Peripheral Control (Printers / Scanners)
Print engines, scanner stepper motors, and legacy USB-to-parallel bridges often require parallel-control glue logic that the EPM7096LC84-10 implements in a single chip. Its 36 I/O pins can drive head-position encoders, paper-feed stepper coils, and LED status banks simultaneously, while the macrocell array handles stepper pulse-train generation and PWM-like dimming control. The instant-on EEPROM configuration means the printer is operational within microseconds of power-up, satisfying warm-boot timing requirements. Replacement of original 74LS glue logic with one CPLD reduces PCB area and improves noise immunity through fewer high-speed signal traces.
Recomendado
JTAG Boundary-Scan Test Access
The built-in IEEE 1149.1 JTAG interface of the EPM7096LC84-10 lets the device itself act as a boundary-scan master or slave in board-level test fixtures. By assigning all 36 user I/O pins to JTAG boundary-scan registers, the CPLD can chain test access to adjacent BGA and QFP devices that lack visible test points. The 10 ns tPD does not limit boundary-scan capture-clock rates since scan operations occur at the JTAG TCK frequency (typically 10-100 MHz), independent of the CPLD's functional tPD. Combined with the ISP capability, the same JTAG port re-loads firmware and runs structural board tests - a true single-test-access design.
Recomendado
Replacement of Discrete TTL Gate Arrays
Designers often face legacy boards populated with 30+ discrete 74LS/74HC/74F packages implementing address decoding, bus arbitration, and interrupt prioritization. The EPM7096LC84-10, with 96 macrocells, can absorb all of these functions into a single 84-PLCC device, reducing PCB area, lowering power consumption through CMOS design, and improving reliability by removing solder joints. The MultiVolt I/O pins let the same CPLD interface to 5-V and 3.3-V logic islands on the board, eliminating the cross-voltage glue that often accompanies mixed-logic redesigns. Migration to the same-die MAX II EPM570 is recommended only if board area constraints demand a smaller package.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para EPM7096LC84-10 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | EPM7096LC84-12 | EPM7096LC84-15 | EPM7128ELC84-15 | EPM7128SLC84-10N | EPM7064LC84-10 |
|---|---|---|---|---|---|---|
| Brand | Intel | Intel | Intel | Intel | Intel | Intel |
| Package | 84-PLCC (J-Lead) | 84-PLCC (J-Lead) - same | 84-PLCC (J-Lead) - same | 84-PLCC (J-Lead) - same | 84-PLCC (J-Lead) - same | 84-PLCC (J-Lead) - same |
| Macrocells | 96 | 96 | 96 | 128 | 128 | 64 |
| Propagation Delay (tPD) | 10 ns | 12 ns | 15 ns | 15 ns | 10 ns | 10 ns |
| Logic Array Blocks | 4 | 4 | 4 | 8 | 8 | 4 |
| Maximum User I/O | 36 | 36 | 36 | 36 | 36 | 36 |
| Supply Voltage | 5.0 V | 5.0 V | 5.0 V | 5.0 V | 5.0 V | 5.0 V |
| In-System Programmability | Yes (JTAG) | Yes (JTAG) | Yes (JTAG) | Yes (JTAG) | Yes (JTAG) | Yes (JTAG) |
| Pin-to-Pin Drop-In | Reference | Yes | Yes | Yes | Yes | Yes |
Principais diferenciais
- Higher macrocell density at same speed grade (vs EPM7064LC84-10)
- Faster speed grade than EPM7128ELC84-15 (vs EPM7128ELC84-15)
- 5-V native supply matches legacy 5-V systems (vs MAX II EPM570 (modern alternative))
Notas de projeto
Estimated: At a 5.0 V VCC with all 36 I/O pins toggling at 25 MHz into 50 pF loads, the EPM7096LC84-10 draws approximately 200-300 mA. Place one 0.1 uF ceramic decoupling capacitor within 5 mm of each VCC pin (pins 84, plus internal supply pins) and a 10 uF bulk tantalum or ceramic capacitor at the board's power-entry point. The four GND pins (11, 23, 41, 55, 69, 83) must all be tied to a low-impedance ground plane; missing even one GND connection can cause intermittent JTAG failures under load.
Route the four JTAG signals (TDI pin 43, TMS pin 44, TCK pin 45, TDO pin 46) as a short, impedance-controlled cluster with a guard ground on either side. Keep JTAG traces under 50 mm to avoid reflection-induced programming failures. The TCK line in particular should be length-matched to within 5 mm of any buffered JTAG node downstream. If the board uses a 10-pin or 14-pin JTAG header, add a 10 kohm pull-up on TMS and TDI per IEEE 1149.1 spec to keep the TAP controller in a benign state during board reset.
Do not assume the -10, -12, and -15 speed-grade variants are interchangeable without re-running timing closure. The 2 ns and 5 ns tPD differences can violate setup/hold margins in synchronous designs clocked above 33 MHz. Pinout is identical across speed grades, so PCB fabrication is unaffected - only the device marking changes. Also note that the 'L' suffix denotes the 5-V low-power CMOS process; the 3.3-V 'S' variants (EPM7096SLC84-10) require VCC of 3.3 V and are NOT pin-compatible at the supply pin - mixing them on the same board will damage the 'L' part.
Informações de conformidade
RoHS/lead-free status not stated in verified web data for this specific MPN. The MAX 7000 family is generally lead-bearing per legacy Altera process; the lead-free variant carries a '-N' suffix in the part number (e.g., EPM7096LC84-10N). Verify against the device marking or manufacturer PCN for production designs.