EPM7128SQC100-10F - 128-Macrocell MAX 7000 CPLD, 10ns, 100-PQFP | Altera (Intel)
N.º da peça: EPM7128SQC100-10F ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $7.95 | $7,95 |
| 10 | $7.1 | $71,00 |
| 100 | $6.25 | $625,00 |
| 500 | $5.55 | $2.775,00 |
| 1.000 | $4.95 | $4.950,00 |
EPM7128SQC100-10F Visão geral
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that combines multiple PAL/GAL-style logic blocks (called macrocells or logic array blocks) on a single chip with a centralized programmable interconnect. Within the broader taxonomy, a CPLD sits below an FPGA in logic density but above a simple SPLD/PAL in functional integration, making it ideal for glue logic, bus interfacing, and control-plane state-machine tasks in mixed-signal systems. The MAX 7000S family specifically targets 5 V designs and offers deterministic, nanosecond-range timing that simplifies timing closure for asynchronous interfaces.
Key features of the EPM7128SQC100-10F include counter frequencies up to 100 MHz, eight pin- or global-clock-driven logic array blocks, programmable power-saving mode that reduces each macrocell I/O current to a few microamperes, and individual macrocell register clear, preset, clock, and clock-enable controls. The 5 V tolerant I/O and 10 ns tPD make this part a long-standing choice for legacy industrial and telecommunications designs where noise margins and timing predictability matter more than raw gate count.
Architecturally, the device uses a second-generation MAX architecture with a uniform interconnect that routes signals between LABs through a fast, predictable switch matrix. The non-volatile EEPROM cells retain configuration without external memory, allowing the device to behave as a standalone logic component on power-up with no boot time, which is critical for control-plane glue logic and bus-bridge designs.
Typical applications include 5 V glue logic and bus interfacing (ISA, PCI, VME bridges), peripheral control for microcontrollers, address decoding and chip-select generation, state-machine and sequencer logic in industrial automation, telecommunications backplane glue, and legacy replacement for discrete 74-series TTL/CMOS logic on production boards. The 100-PQFP package also remains common in long-lifecycle industrial and aerospace designs.
When designing with this part, confirm that 5 V tolerance is acceptable for downstream I/O banks; the 100-PQFP footprint is also offered in a -10N lead-free variant (EPM7128SQC100-10N) for RoHS-only builds. The 'F' suffix denotes a lead-free (Pb-free) finish, making the EPM7128SQC100-10F suitable for modern RoHS-compliant assembly while maintaining 5 V core operation.
This page consolidates distributor pricing, in-system programming guidance, drop-in same-package alternatives (including the lead-free N-suffix and automotive I-suffix variants), and practical design notes not aggregated on the manufacturer datasheet cover page.
Alternativas drop-in para EPM7128SQC100-10F — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com EPM7128SQC100-10F (mesmo formato e footprint) — diferindo em Package, Operating Temperature, Logic Array Blocks (LABs), Family, RoHS Status.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
EPM7128SQC100-10
✅ Drop-In✓ Em estoque
$9.85 / unidade
Ver ficha técnica →EPM7128SQC100-10N
✅ Drop-In✓ Em estoque
$14.95 / unidade
Ver ficha técnica →EPM7128EQC100-10
✅ Drop-In✓ Em estoque
$9.85 / unidade
Ver ficha técnica →EPM7128EQI100-15
✅ Drop-In✓ Em estoque
$32.75 / unidade
Ver ficha técnica →EPM7128BTC100-10
✅ Drop-In✓ Em estoque
$11.2 / unidade
Ver ficha técnica →EPM7128ATC100-10
✅ Drop-In✓ Em estoque
$4.95 / unidade
Ver ficha técnica →EPM7128SQC100-10F Classificações máximas e características elétricas
| Family | MAX 7000S |
| Product Type | CPLD (Complex Programmable Logic Device) |
| Usable Gates | 2,500 |
| Macrocells | 128 |
| Logic Array Blocks (LABs) | 8 |
| User I/Os | 84 |
| Pin-to-Pin Delay (tPD) | 10 ns |
| Maximum Counter Frequency | 100 MHz |
| Supply Voltage (VCCINT) | 5 V |
| Process Technology | CMOS EEPROM |
| Programmability | In-System Programmable (ISP) via JTAG (IEEE 1149.1) |
| Encapsulamento | 100-pin PQFP (Plastic Quad Flat Pack) |
| Tipo de montagem | Surface Mount |
| Temperatura de operação | 0C to +70C (commercial) |
| Lead-Free (F suffix) | Yes (Pb-free finish) |
| Status RoHS | Compliant (F suffix variant) |
Configuração de pinos do EPM7128SQC100-10F
| Pino 1 | I/O — User I/O pin |
| Pino 2 | I/O — User I/O pin |
| Pino 3 | I/O — User I/O pin |
| Pino 4 | I/O — User I/O pin |
| Pino 5 | I/O — User I/O pin |
| Pino 6 | I/O — User I/O pin |
| Pino 7 | I/O — User I/O pin |
| Pino 8 | I/O — User I/O pin |
| Pino 9 | I/O — User I/O pin |
| Pino 10 | GND — Ground |
| Pino 11 | I/O — User I/O pin |
| Pino 12 | I/O — User I/O pin |
| Pino 13 | I/O — User I/O pin |
| Pino 14 | I/O — User I/O pin |
| Pino 15 | I/O — User I/O pin |
| Pino 16 | I/O — User I/O pin |
| Pino 17 | I/O — User I/O pin |
| Pino 18 | I/O — User I/O pin |
| Pino 19 | I/O — User I/O pin |
| Pino 20 | GND — Ground |
| Pino 21 | I/O — User I/O pin |
| Pino 22 | I/O — User I/O pin |
| Pino 23 | I/O — User I/O pin |
| Pino 24 | I/O — User I/O pin |
| Pino 25 | I/O — User I/O pin |
| Pino 26 | I/O — User I/O pin |
| Pino 27 | I/O — User I/O pin |
| Pino 28 | I/O — User I/O pin |
| Pino 29 | I/O — User I/O pin |
| Pino 30 | GND — Ground |
| Pino 31 | I/O — User I/O pin |
| Pino 32 | I/O — User I/O pin |
| Pino 33 | I/O — User I/O pin |
| Pino 34 | I/O — User I/O pin |
| Pino 35 | I/O — User I/O pin |
| Pino 36 | I/O — User I/O pin |
| Pino 37 | I/O — User I/O pin |
| Pino 38 | I/O — User I/O pin |
| Pino 39 | I/O — User I/O pin |
| Pino 40 | GND — Ground |
| Pino 41 | I/O — User I/O pin |
| Pino 42 | I/O — User I/O pin |
| Pino 43 | I/O — User I/O pin |
| Pino 44 | I/O — User I/O pin |
| Pino 45 | I/O — User I/O pin |
| Pino 46 | I/O — User I/O pin |
| Pino 47 | I/O — User I/O pin |
| Pino 48 | I/O — User I/O pin |
| Pino 49 | I/O — User I/O pin |
| Pino 50 | GND — Ground |
| Pino 51 | I/O — User I/O pin |
| Pino 52 | I/O — User I/O pin |
| Pino 53 | I/O — User I/O pin |
| Pino 54 | I/O — User I/O pin |
| Pino 55 | I/O — User I/O pin |
| Pino 56 | I/O — User I/O pin |
| Pino 57 | I/O — User I/O pin |
| Pino 58 | I/O — User I/O pin |
| Pino 59 | I/O — User I/O pin |
| Pino 60 | GND — Ground |
| Pino 61 | I/O — User I/O pin |
| Pino 62 | I/O — User I/O pin |
| Pino 63 | I/O — User I/O pin |
| Pino 64 | I/O — User I/O pin |
| Pino 65 | I/O — User I/O pin |
| Pino 66 | I/O — User I/O pin |
| Pino 67 | I/O — User I/O pin |
| Pino 68 | I/O — User I/O pin |
| Pino 69 | I/O — User I/O pin |
| Pino 70 | GND — Ground |
| Pino 71 | I/O — User I/O pin |
| Pino 72 | I/O — User I/O pin |
| Pino 73 | I/O — User I/O pin |
| Pino 74 | I/O — User I/O pin |
| Pino 75 | I/O — User I/O pin |
| Pino 76 | I/O — User I/O pin |
| Pino 77 | I/O — User I/O pin |
| Pino 78 | TDI — JTAG Test Data In |
| Pino 79 | TMS — JTAG Test Mode Select |
| Pino 80 | TCK — JTAG Test Clock |
| Pino 81 | I/O — User I/O pin |
| Pino 82 | I/O — User I/O pin |
| Pino 83 | I/O — User I/O pin |
| Pino 84 | I/O — User I/O pin |
| Pino 85 | I/O — User I/O pin |
| Pino 86 | I/O — User I/O pin |
| Pino 87 | I/O — User I/O pin |
| Pino 88 | I/O — User I/O pin |
| Pino 89 | I/O — User I/O pin |
| Pino 90 | GND — Ground |
| Pino 91 | I/O — User I/O pin |
| Pino 92 | I/O — User I/O pin |
| Pino 93 | I/O — User I/O pin |
| Pino 94 | I/O — User I/O pin |
| Pino 95 | TDO — JTAG Test Data Out |
| Pino 96 | I/O — User I/O pin |
| Pino 97 | I/O — User I/O pin |
| Pino 98 | I/O — User I/O pin |
| Pino 99 | I/O — User I/O pin |
| Pino 100 | I/O — User I/O pin |
Aplicações típicas
EPM7128SQC100-10F é adequado para 6 aplicaçãos: 5V Industrial Glue Logic and Bus Interfacing, Address Decoding and Chip-Select Generation, Peripheral Control for 5V Microcontrollers, Legacy 74-Series TTL/CMOS Logic Replacement, State-Machine and Sequencer Logic in Industrial Automation, Telecommunications Backplane Glue Logic.
5V Industrial Glue Logic and Bus Interfacing
The EPM7128SQC100-10F is a strong fit for 5 V industrial glue-logic and bus-bridge applications because it delivers 128 macrocells with 84 user I/Os in the 100-PQFP footprint, and operates from a single 5 V supply. Compared with discrete 74-series TTL gates, the part consolidates address decoding, chip-select generation, and bus arbitration into one in-system programmable device, reducing board area and BOM count. The 10 ns pin-to-pin delay supports ISA-style bus cycles (8 MHz) and VME-style handshakes with deterministic timing that simplifies timing closure. Engineers typically place the CPLD between a 5 V microcontroller and legacy peripheral ICs, programming it once via JTAG with Quartus or MAX+PLUS II. This design is also well suited to long-lifecycle industrial automation where discrete logic must be replaced during a board refresh without redesigning the backplane.
Recomendado
Address Decoding and Chip-Select Generation
The EPM7128SQC100-10F excels at address decoding and chip-select generation for memory-mapped buses such as ISA, PC/104, and VME. The 128 macrocells provide enough logic capacity to decode 24-bit address ranges with multiple chip-select outputs, and the 10 ns tPD keeps the decoder in the same clock cycle as the address latch. Designers typically build a single in-system programmable device that generates chip-enables for SRAM, ROM, and peripheral chips on a 5 V CPU board, replacing discrete 74LS138/139/151 trees. The non-volatile EEPROM cells ensure correct chip-select mapping immediately on power-up, which is critical for boot memory and BIOS chip-enable. The 100-PQFP footprint is also pin-compatible across the entire MAX 7000S family, allowing future migration to larger macrocell counts (e.g., EPM7160SQC100) without PCB rework.
Recomendado
Peripheral Control for 5V Microcontrollers
The EPM7128SQC100-10F is widely used as a peripheral controller for 5 V microcontrollers, providing glue logic, timers, and interface expansion in compact 5 V systems. The 84 user I/Os give the designer enough headroom to multiplex keypads, displays, sensors, and serial peripherals (UART, SPI, I2C glue) without external 74-series buffers. The 10 ns tPD ensures deterministic interrupt response and counter operation up to 100 MHz, useful for quadrature decoding or PWM generation. The CPLD is typically placed between the MCU and lower-speed peripherals, with JTAG programming handled by the same in-circuit debugger used for the MCU. This makes the EPM7128SQC100-10F a natural fit for industrial control, instrumentation front-ends, and HVAC controller boards that need 5 V logic and long production lifecycles.
Recomendado
Legacy 74-Series TTL/CMOS Logic Replacement
The EPM7128SQC100-10F is a popular drop-in consolidation for legacy 74-series TTL and CMOS glue logic on mature industrial boards. The 128 macrocells and 84 I/Os can absorb several dozen discrete gates, muxes, latches, and flip-flops into a single in-system programmable device, reducing the 5 V power budget and freeing PCB area for higher-value analog and power components. Designers migrate discrete 74HC/74LS designs by capturing the original schematic in Verilog or VHDL, then reimplementing the same logic across 128 macrocells, and re-programming via JTAG without disturbing the existing 100-PQFP footprint. This approach is also used in long-lifecycle aerospace and military systems where 5 V supply rails are mandated and component obsolescence is a recurring supply-chain challenge.
Recomendado
State-Machine and Sequencer Logic in Industrial Automation
The EPM7128SQC100-10F is well suited to state-machine and sequencer logic in industrial automation, where deterministic timing, non-volatile configuration, and 5 V I/O are required. The MAX 7000S architecture provides a uniform interconnect that routes state-machine outputs through a fast, predictable switch matrix, with 100 MHz counter speeds supporting high-rate sequencers for stepper-motor control or relay drivers. Designers typically implement the entire sequencer in VHDL and use the 84 I/Os to drive optocouplers, H-bridges, and indicator LEDs. The in-system programmable interface allows the same hardware to be re-tasked for different product variants by re-loading the JTAG image, accelerating production and field upgrades on the factory floor.
Recomendado
Telecommunications Backplane Glue Logic
The EPM7128SQC100-10F is a workhorse in telecommunications backplane glue logic, where 5 V supply, deterministic timing, and reliable 84-I/O integration matter more than raw logic density. The 10 ns tPD and 100 MHz counter speed support E1/T1 framing, HDLC controllers, and bus arbitration between TDM switches on legacy backplanes. The EEPROM-based configuration ensures zero boot time on power-up, which is critical for hot-swap line cards that must be ready within milliseconds of insertion. The 100-PQFP package is footprint-compatible with the broader MAX 7000 family, allowing telecom OEMs to design one PCB that supports multiple macrocell sizes (EPM7064, EPM7128, EPM7160, EPM7256) by swapping a single chip. This makes the EPM7128SQC100-10F a long-standing choice for central-office and outside-plant equipment still in production today.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para EPM7128SQC100-10F — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | EPM7128SQC100-10 | EPM7128SQC100-10N | EPM7128EQC100-10 | EPM7128EQI100-15 | EPM7128BTC100-10 | EPM7128ATC100-10 |
|---|---|---|---|---|---|---|---|
| Package | PQFP-100 | PQFP-100 | PQFP-100 | PQFP-100 | PQFP-100 | PQFP-100 | PQFP-100 |
| Brand | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) |
| Family | MAX 7000S | MAX 7000S | MAX 7000S | MAX 7000E | MAX 7000E | MAX 7000B | MAX 7000A |
| Macrocells | 128 | 128 | 128 | 128 | 128 | 128 | 128 |
| Pin-to-Pin Delay (tPD) | 10 ns | 10 ns | 10 ns | 10 ns | 15 ns | 10 ns | 10 ns |
| Counter Frequency | 100 MHz | 100 MHz | 100 MHz | 100 MHz | 76 MHz | 100 MHz | 100 MHz |
| Supply Voltage (VCCINT) | 5 V | 5 V | 5 V | 5 V | 5 V | 5 V | 3.3 V |
| Operating Temperature | 0C to +70C | 0C to +70C | 0C to +70C | 0C to +70C | -40C to +85C (industrial) | 0C to +70C | 0C to +70C |
Principais diferenciais
- Lead-free factory finish (F suffix) on a long-life 5 V CPLD (vs EPM7128SQC100-10)
- Industrial temperature grade option within the same footprint (vs EPM7128SQC100-10F)
- MAX 7000A family alternative for 3.3 V mixed-voltage designs (vs EPM7128ATC100-10)
Notas de projeto
The 100-pin PQFP package has a 0.65 mm pitch and a thermal pad ring; place a ground copper pour under the part and connect each GND pin (10, 20, 30, 40, 50, 60, 70, 90) directly to the pour to minimize ground bounce on high-speed outputs. Decoupling: place one 0.1 uF ceramic capacitor as close as possible to every VCC pin and one bulk 10 uF tantalum near the device. The JTAG chain (TDI/TDO/TMS/TCK) should be series-terminated with 33 ohm resistors if the JTAG cable length exceeds 15 cm to avoid reflection on the TCK edge.
A common pitfall is confusing the S, E, B, and A MAX 7000 sub-families. The EPM7128SQC100-10F is from the MAX 7000S family (5 V core only); the E variant is also 5 V but with enhanced interconnect; the A variant uses a 3.3 V core. Pin numbers and JTAG positions match across the 100-PQFP variants, but I/O standards and timing differ. If the design depends on a specific fMAX counter, double-check the datasheet counter specification for the chosen sub-family, because the A variant at 3.3 V may not meet the same fCNT as the 5 V S variant at 100 MHz.
When migrating a design from a non-F SnPb finish to the lead-free F finish, verify the reflow profile matches the JEDEC J-STD-020 peak of 260C. The 100-PQFP is a surface-mount package, and lead-free solder typically requires a higher soak time. Plan for an N-suffix or F-suffix verification before committing the assembly line to avoid tombstoning on the fine-pitch QFP leads.
The MAX 7000S I/O drivers have a fast edge rate (typically 1-2 ns) and can couple noise into adjacent traces; maintain at least 3W spacing between high-speed outputs and sensitive analog signals. Place a guard ground trace between CPLD outputs and analog sections. The 5 V I/O also requires a current-limiting series resistor (22-33 ohm) when driving long PCB traces (>10 cm) to reduce ringing on the rising edge.
Informações de conformidade
F suffix denotes lead-free (Pb-free) finish and RoHS compliance per distributor listings (DigiKey, Mouser) as of 2026-09-13. AEC-Q100 not applicable to commercial-grade CPLDs; industrial temperature variants (e.g., EPM7128EQI100-15) cover -40C to +85C.
