ISL8491IB-T - 5V RS-485/RS-422 Transceiver | Renesas
N.º da peça: ISL8491IB-T ✓ AtivoISL8491IB-T Visão geral
A transceiver is an interface IC that converts logic-level signals into differential bus levels and converts received differential signals back into logic levels. RS-422 supports point-to-point balanced communication, while RS-485 supports longer multipoint buses. The ISL8491IB-T places the balanced driver and receiver in one 14-SOIC package, reducing component count on communication interfaces that require both transmission and reception.
The ISL8491IB-T operates from 5 V, supports communications through 5 Mbps, and includes ESD protection according to its product descriptions. Its slew-rate-limited behavior helps control the transition rate applied to the bus, which is important when reducing high-frequency harmonics and signal-integrity problems in cables, connectors, and long wiring. The 14-pin SOIC package supports conventional surface-mount assembly and is widely compatible with industrial control-board layouts.
The device is based on a low-power, high-speed BiCMOS process. Combining bipolar and CMOS characteristics supports the interface requirements of a 5 V communication circuit while retaining the low-power characteristics expected in industrial equipment. The integrated driver-receiver arrangement simplifies bidirectional bus connections, although protocol direction control, termination, biasing, and isolation remain functions of the complete interface circuit.
Typical uses include industrial automation controllers, factory data-collection equipment, building-control gateways, instrumentation, and embedded RS-485 or RS-422 ports. It can also serve as the physical-layer interface in systems that exchange commands and sensor data across a balanced bus. The 5 Mbps capability is relevant for factory and industrial links, while the slew-rate limiting should be considered when selecting cable length, topology, and termination.
PCB design should follow the pin-description table in the manufacturer datasheet when assigning signal traces and supply connections. Keep the transceiver close to the bus connector, provide the required local supply decoupling, and place termination and fail-safe bias components where they can be reached without long stubs. Confirm the selected connector, cable, and grounding strategy against the communication standard used by the system.
This product page combines the verified 5 V, 5 Mbps, RS-485/RS-422, ESD, BiCMOS, and 14-SOIC characteristics with practical interface-design guidance, sourcing information, and pin-compatible alternatives. It also helps engineers identify which details must still be confirmed in the manufacturer datasheet before schematic release or PCB sign-off.
Alternativas drop-in para ISL8491IB-T — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com ISL8491IB-T (mesmo formato e footprint) — diferindo em ESD Protection, Supported Standards.
ISL8491IB
✅ Drop-InConsulte o preço
Ver ficha técnica →ISL8491IBZ-T
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ISL8491IB-T Especificações
| Product Type | Single RS-485/RS-422 transceiver |
| Manufacturer | Renesas Electronics |
| Tensão de alimentação | 5 V |
| Maximum Data Rate | 5 Mbps |
| Number of Drivers | 1 |
| Number of Receivers | 1 |
| Supported Standards | RS-422 and RS-485 |
| Logic Technology | BiCMOS |
| Slew Rate | Slew-rate limited |
| ESD Protection | Present |
| Encapsulamento | 14-pin SOIC |
| Tipo de montagem | Surface mount |
| Status RoHS | Compliant |
Guia de Configuração de Pinos do ISL8491IB-T 14-pin soic
Configuração de pinos para ISL8491IB-T (pacote 14-pin soic). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para ISL8491IB-T.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
ISL8491IB-T é adequado para 6 aplicaçãos: Industrial Automation Bus Interface, Factory Sensor Data Collection, Building Control Gateway, Test and Measurement Instrument, Industrial Motor Controller, Embedded Communication Module.
Industrial Automation Bus Interface
The ISL8491IB-T fits a 5 V industrial automation node that communicates over a balanced RS-485 or RS-422 bus. Its single integrated driver and receiver reduce the number of interface devices required at the controller boundary, while operation up to 5 Mbps supports relatively fast command and process-data exchanges. The 14-SOIC package simplifies assembly on mixed-signal control boards. Designers should verify enable timing, bus direction control, termination, and fail-safe biasing in the manufacturer datasheet. Slew-rate limiting also makes the interface relevant to factory environments where controlled edge rates and ESD protection help reduce unwanted emissions and transient susceptibility.
Recomendado
Factory Sensor Data Collection
The ISL8491IB-T can serve as the physical-layer transceiver between a data collector and remotely located sensors using an RS-485 balanced bus. Its 5 V operation is compatible with conventional embedded control logic, and the 5 Mbps maximum data rate supports efficient collection of status, configuration, and measurement data. The integrated one-driver, one-receiver arrangement provides a compact implementation without selecting separate transmitter and receiver packages. Cable length and topology should be validated together with slew-rate-limited signaling, while local decoupling and bus termination must follow the manufacturer reference circuit.
Recomendado
Building Control Gateway
The ISL8491IB-T is suitable for a building-control gateway that links a controller to an RS-485 or RS-422 field network. Its differential transceiver supports noise-resistant communication over wiring that may run near lighting, motors, and switching equipment, while ESD protection adds useful interface robustness. A 14-SOIC package allows the transceiver to be placed near the terminal block and keep sensitive communication routing away from processor and power-conversion areas. Confirm grounding, isolation strategy, termination placement, and updated compliance requirements for the final building-control product.
Recomendado
Test and Measurement Instrument
The ISL8491IB-T can provide the balanced communication link used by laboratory and field-test equipment that exchanges commands or measurement records with remote fixtures. Its 5 Mbps capability offers useful bandwidth for instrument-control traffic, while the integrated driver and receiver conserve board area in compact instruments. The 14-SOIC package is convenient for mixed-signal PCB assembly, although analog and digital grounds should be managed carefully to prevent bus noise from affecting sensitive measurements. Use the manufacturer pin descriptions to route the transceiver close to the connector and preserve a short return path.
Recomendado
Industrial Motor Controller
The ISL8491IB-T can connect an industrial motor controller to external drives, programmable logic controllers, or supervisory equipment over RS-485 or RS-422. Differential signaling is well suited to electrically noisy machinery environments, and the device's ESD protection and slew-rate-limited behavior help control interface stress and emissions. The 5 V supply aligns with many embedded controller rails. The design should separate transceiver routing from high-current motor switching paths, follow the manufacturer grounding guidance, and verify whether the system requires galvanic isolation rather than relying on the integrated device alone.
Recomendado
Embedded Communication Module
The ISL8491IB-T fits a compact embedded module that exposes an RS-485 or RS-422 port for configuration, diagnostics, or external sensors. One driver and one receiver in a 14-SOIC package allow the module to support bidirectional communication while leaving space for processing and power circuitry. Its 5 V supply and 5 Mbps maximum rate suit short, controlled links. Designers should implement bus-direction control, optional termination, and fail-safe biasing as defined by the manufacturer, and should verify the exact operating-temperature grade and ESD conditions before deploying the module in an enclosure with exposed wiring.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para ISL8491IB-T — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | ISL8491IB | ISL8491IBZ-T |
|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 14-SOIC | 14-SOIC - same | 14-SOIC - same |
| Supply Voltage | 5 V | 5 V | 5 V |
| Maximum Data Rate | 5 Mbps | 5 Mbps | 5 Mbps |
| Driver and Receiver Count | 1 driver and 1 receiver | 1 driver and 1 receiver | 1 driver and 1 receiver |
| Supported Standards | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 |
| Logic Technology | BiCMOS | BiCMOS | BiCMOS |
| Slew-Rate Behavior | Slew-rate limited | Slew-rate limited | Slew-rate limited |
| ESD Protection | Present | Present | Present |
Principais diferenciais
- High-speed balanced communication in a compact package (vs ISL8491IB)
- Documented terminal and package consistency (vs ISL8491IBZ-T)
- Integrated balanced interface (vs ISL8491IBZ-T)
Notas de projeto
Place the ISL8491IB-T close to the RS-485 or RS-422 connector and keep the balanced traces short and tightly coupled. Route the pair as a differential pair over a continuous reference plane, avoid splitting the ground reference beneath the interface, and keep switching-regulator and high-current motor traces away from the bus nodes. Confirm the exact terminal assignments in the manufacturer pin-description table before assigning nets.
Treat termination, fail-safe biasing, cable length, and topology as one network design. The ISL8491IB-T has slew-rate-limited signaling, which can help control harmonics, but it does not remove the need for a sound bus network. Determine whether termination belongs at both physical ends of a point-to-point RS-422 link or at appropriate locations in an RS-485 topology, and avoid long branches or unnecessary stubs.
Do not substitute an 8-pin transceiver for the 14-pin ISL8491IB-T merely because both support RS-485. The package, terminal count, enable logic, receiver behavior, and supply requirements must all be compatible. Before production release, compare the complete pin-description table, absolute-maximum ratings, recommended operating circuit, and electrical characteristics for the selected substitute against the original design requirements.
Informações de conformidade
RoHS status is identified by the component listing. Other environmental, automotive, and material-compliance declarations are not stated and therefore remain unknown.