ISL8491IB-T - 5V RS-485/RS-422 Transceiver | Renesas
MPN: ISL8491IB-T ✓ 啟用中ISL8491IB-T 概覽
A transceiver is an interface IC that converts logic-level signals into differential bus levels and converts received differential signals back into logic levels. RS-422 supports point-to-point balanced communication, while RS-485 supports longer multipoint buses. The ISL8491IB-T places the balanced driver and receiver in one 14-SOIC package, reducing component count on communication interfaces that require both transmission and reception.
The ISL8491IB-T operates from 5 V, supports communications through 5 Mbps, and includes ESD protection according to its product descriptions. Its slew-rate-limited behavior helps control the transition rate applied to the bus, which is important when reducing high-frequency harmonics and signal-integrity problems in cables, connectors, and long wiring. The 14-pin SOIC package supports conventional surface-mount assembly and is widely compatible with industrial control-board layouts.
The device is based on a low-power, high-speed BiCMOS process. Combining bipolar and CMOS characteristics supports the interface requirements of a 5 V communication circuit while retaining the low-power characteristics expected in industrial equipment. The integrated driver-receiver arrangement simplifies bidirectional bus connections, although protocol direction control, termination, biasing, and isolation remain functions of the complete interface circuit.
Typical uses include industrial automation controllers, factory data-collection equipment, building-control gateways, instrumentation, and embedded RS-485 or RS-422 ports. It can also serve as the physical-layer interface in systems that exchange commands and sensor data across a balanced bus. The 5 Mbps capability is relevant for factory and industrial links, while the slew-rate limiting should be considered when selecting cable length, topology, and termination.
PCB design should follow the pin-description table in the manufacturer datasheet when assigning signal traces and supply connections. Keep the transceiver close to the bus connector, provide the required local supply decoupling, and place termination and fail-safe bias components where they can be reached without long stubs. Confirm the selected connector, cable, and grounding strategy against the communication standard used by the system.
This product page combines the verified 5 V, 5 Mbps, RS-485/RS-422, ESD, BiCMOS, and 14-SOIC characteristics with practical interface-design guidance, sourcing information, and pin-compatible alternatives. It also helps engineers identify which details must still be confirmed in the manufacturer datasheet before schematic release or PCB sign-off.
直接替換替代品,適用於 ISL8491IB-T — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: ISL8491IB-T (相同外形與佔位) — 差異在於 ESD Protection, Supported Standards.
ISL8491IB
✅ 直接替換聯絡詢價
查看資料表 →ISL8491IBZ-T
✅ 直接替換📋 參考替代品(不在目錄中)
ISL8491IB-T 規格
| Product Type | Single RS-485/RS-422 transceiver |
| Manufacturer | Renesas Electronics |
| 供應電壓 | 5 V |
| Maximum Data Rate | 5 Mbps |
| Number of Drivers | 1 |
| Number of Receivers | 1 |
| Supported Standards | RS-422 and RS-485 |
| Logic Technology | BiCMOS |
| Slew Rate | Slew-rate limited |
| ESD Protection | Present |
| 封裝 | 14-pin SOIC |
| 安裝類型 | Surface mount |
| RoHS 狀態 | Compliant |
ISL8491IB-T 14-pin soic 腳位配置指南
ISL8491IB-T(14-pin soic 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: ISL8491IB-T.
請參閱 資料表 以查看完整腳位配置。
典型應用
ISL8491IB-T 適用於 6 應用s: Industrial Automation Bus Interface, Factory Sensor Data Collection, Building Control Gateway, Test and Measurement Instrument, Industrial Motor Controller, Embedded Communication Module.
Industrial Automation Bus Interface
The ISL8491IB-T fits a 5 V industrial automation node that communicates over a balanced RS-485 or RS-422 bus. Its single integrated driver and receiver reduce the number of interface devices required at the controller boundary, while operation up to 5 Mbps supports relatively fast command and process-data exchanges. The 14-SOIC package simplifies assembly on mixed-signal control boards. Designers should verify enable timing, bus direction control, termination, and fail-safe biasing in the manufacturer datasheet. Slew-rate limiting also makes the interface relevant to factory environments where controlled edge rates and ESD protection help reduce unwanted emissions and transient susceptibility.
推薦
Factory Sensor Data Collection
The ISL8491IB-T can serve as the physical-layer transceiver between a data collector and remotely located sensors using an RS-485 balanced bus. Its 5 V operation is compatible with conventional embedded control logic, and the 5 Mbps maximum data rate supports efficient collection of status, configuration, and measurement data. The integrated one-driver, one-receiver arrangement provides a compact implementation without selecting separate transmitter and receiver packages. Cable length and topology should be validated together with slew-rate-limited signaling, while local decoupling and bus termination must follow the manufacturer reference circuit.
推薦
Building Control Gateway
The ISL8491IB-T is suitable for a building-control gateway that links a controller to an RS-485 or RS-422 field network. Its differential transceiver supports noise-resistant communication over wiring that may run near lighting, motors, and switching equipment, while ESD protection adds useful interface robustness. A 14-SOIC package allows the transceiver to be placed near the terminal block and keep sensitive communication routing away from processor and power-conversion areas. Confirm grounding, isolation strategy, termination placement, and updated compliance requirements for the final building-control product.
推薦
Test and Measurement Instrument
The ISL8491IB-T can provide the balanced communication link used by laboratory and field-test equipment that exchanges commands or measurement records with remote fixtures. Its 5 Mbps capability offers useful bandwidth for instrument-control traffic, while the integrated driver and receiver conserve board area in compact instruments. The 14-SOIC package is convenient for mixed-signal PCB assembly, although analog and digital grounds should be managed carefully to prevent bus noise from affecting sensitive measurements. Use the manufacturer pin descriptions to route the transceiver close to the connector and preserve a short return path.
推薦
Industrial Motor Controller
The ISL8491IB-T can connect an industrial motor controller to external drives, programmable logic controllers, or supervisory equipment over RS-485 or RS-422. Differential signaling is well suited to electrically noisy machinery environments, and the device's ESD protection and slew-rate-limited behavior help control interface stress and emissions. The 5 V supply aligns with many embedded controller rails. The design should separate transceiver routing from high-current motor switching paths, follow the manufacturer grounding guidance, and verify whether the system requires galvanic isolation rather than relying on the integrated device alone.
推薦
Embedded Communication Module
The ISL8491IB-T fits a compact embedded module that exposes an RS-485 or RS-422 port for configuration, diagnostics, or external sensors. One driver and one receiver in a 14-SOIC package allow the module to support bidirectional communication while leaving space for processing and power circuitry. Its 5 V supply and 5 Mbps maximum rate suit short, controlled links. Designers should implement bus-direction control, optional termination, and fail-safe biasing as defined by the manufacturer, and should verify the exact operating-temperature grade and ESD conditions before deploying the module in an enclosure with exposed wiring.
推薦
推薦產品摘要
工程參考資料,適用於 ISL8491IB-T — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ISL8491IB | ISL8491IBZ-T |
|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 14-SOIC | 14-SOIC - same | 14-SOIC - same |
| Supply Voltage | 5 V | 5 V | 5 V |
| Maximum Data Rate | 5 Mbps | 5 Mbps | 5 Mbps |
| Driver and Receiver Count | 1 driver and 1 receiver | 1 driver and 1 receiver | 1 driver and 1 receiver |
| Supported Standards | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 |
| Logic Technology | BiCMOS | BiCMOS | BiCMOS |
| Slew-Rate Behavior | Slew-rate limited | Slew-rate limited | Slew-rate limited |
| ESD Protection | Present | Present | Present |
主要差異化特點
- High-speed balanced communication in a compact package (對比ISL8491IB)
- Documented terminal and package consistency (對比ISL8491IBZ-T)
- Integrated balanced interface (對比ISL8491IBZ-T)
設計說明
Place the ISL8491IB-T close to the RS-485 or RS-422 connector and keep the balanced traces short and tightly coupled. Route the pair as a differential pair over a continuous reference plane, avoid splitting the ground reference beneath the interface, and keep switching-regulator and high-current motor traces away from the bus nodes. Confirm the exact terminal assignments in the manufacturer pin-description table before assigning nets.
Treat termination, fail-safe biasing, cable length, and topology as one network design. The ISL8491IB-T has slew-rate-limited signaling, which can help control harmonics, but it does not remove the need for a sound bus network. Determine whether termination belongs at both physical ends of a point-to-point RS-422 link or at appropriate locations in an RS-485 topology, and avoid long branches or unnecessary stubs.
Do not substitute an 8-pin transceiver for the 14-pin ISL8491IB-T merely because both support RS-485. The package, terminal count, enable logic, receiver behavior, and supply requirements must all be compatible. Before production release, compare the complete pin-description table, absolute-maximum ratings, recommended operating circuit, and electrical characteristics for the selected substitute against the original design requirements.
合規資訊
RoHS status is identified by the component listing. Other environmental, automotive, and material-compliance declarations are not stated and therefore remain unknown.