LM2902VDTBR2 - 3-26V Quad Low-Power Op Amp | onsemi
N.º da peça: LM2902VDTBR2 ✓ AtivoLM2902VDTBR2 Visão geral
An operational amplifier is a voltage-gain building block used in the wider semiconductor hierarchy of analog integrated circuits. It compares an inverting input with a non-inverting input and drives its output toward the difference between those voltages. Operational amplifiers support signal amplification, buffering, filtering, sensing, and closed-loop control, while the LM2902 combines four amplifiers in one package to reduce board area and simplify dual-rail or single-supply analog signal chains.
The quad configuration provides four independent amplifier channels, making LM2902VDTBR2 useful in industrial control, instrumentation, sensor interfaces, audio preamplification, and general analog processing. Its single-supply operation is particularly valuable in systems using a 3 V to 26 V rail. True differential inputs improve flexibility when the source signal is referenced to a local ground or a different point within the system rather than directly to the common supply ground.
The LM2902 family is positioned as a low-cost, low-power alternative to precision operational amplifiers. This makes it appropriate for general-purpose designs where modest offset and bandwidth are acceptable and system robustness, supply range, and channel density are more important than low-offset or high-speed performance. The four channels share a common package but retain independent input and output connections, allowing different stages to operate in the same assembly.
Typical uses include amplifying sensor outputs, buffering ADC inputs, conditioning low-frequency analog signals, implementing active filters, and providing gain stages in industrial equipment. Its 40 mA per-channel output capability is useful for moderate loads, but output drive and stability must be evaluated against the selected feedback network and load capacitance. A quad package also requires careful grounding to prevent output currents on one channel from disturbing sensitive nodes on another.
For stable operation, follow the manufacturer recommendation for bypassing the supply rail and configure compensation or feedback according to the application circuit in the LM2902 datasheet. Keep sensitive input and feedback traces away from output and supply-return paths. When replacing another amplifier, verify pin assignments, common-mode range, output swing, unity-gain stability, and load drive rather than assuming that similar voltage ratings guarantee equivalent behavior.
This product guide combines the LM2902VDTBR2 electrical limits, package information, drop-in candidates, comparison parameters, and practical PCB guidance. It highlights where a low-cost quad amplifier is suitable and where precision, high speed, low offset, rail-to-rail operation, or automotive qualification would justify a different device.
Alternativas drop-in para LM2902VDTBR2 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com LM2902VDTBR2 (mesmo formato e footprint) — diferindo em Product Type.
LM2902DTB
✅ Drop-InConsulte o preço
Ver ficha técnica →LM2902DTBR2G
✅ Drop-InConsulte o preço
Ver ficha técnica →LM2902VDTB
✅ Drop-InConsulte o preço
Ver ficha técnica →LM2902DTB
✅ Drop-InConsulte o preço
Ver ficha técnica →LM2902DB
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LM2902VDTBR2 Classificações máximas e características elétricas
| Product Type | Single-supply quad operational amplifier |
| Number of Amplifier Channels | 4 circuits |
| Supply Voltage Range | 3 V to 26 V |
| Faixa de temperatura de operação | -40°C to +105°C |
| Output Current per Channel | 40 mA maximum |
| Input Bias Current | 90 nA maximum |
| Differential Input | True differential input |
| Package Type | 14-TSSOP |
| Package Pin Count | 14 pins |
| Package Width | 4.40 mm |
| Package Width Alternate Value | 0.173 inch |
| Tipo de montagem | Surface mount |
| Número de saídas | 4 outputs |
| Number of Input Pairs | 4 input pairs |
| Status RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
Configuração de pinos do LM2902VDTBR2
| Pino 1 | OUT1 — Amplifier 1 output |
| Pino 2 | IN1- — Amplifier 1 inverting input |
| Pino 3 | IN1+ — Amplifier 1 non-inverting input |
| Pino 4 | GND — Common ground connection |
| Pino 5 | IN2+ — Amplifier 2 non-inverting input |
| Pino 6 | IN2- — Amplifier 2 inverting input |
| Pino 7 | OUT2 — Amplifier 2 output |
| Pino 8 | OUT3 — Amplifier 3 output |
| Pino 9 | IN3- — Amplifier 3 inverting input |
| Pino 10 | IN3+ — Amplifier 3 non-inverting input |
| Pino 11 | GND — Common ground connection |
| Pino 12 | IN4+ — Amplifier 4 non-inverting input |
| Pino 13 | IN4- — Amplifier 4 inverting input |
| Pino 14 | OUT4 — Amplifier 4 output |
Aplicações típicas
LM2902VDTBR2 é adequado para 6 aplicaçãos: Industrial Sensor Signal Conditioning, ADC Input Buffering, Low-Frequency Active Filters, Audio Preamplification, Instrumentation and Control Loops, Power Supply Monitoring.
Industrial Sensor Signal Conditioning
The LM2902VDTBR2 fits industrial sensor interfaces that require several amplified channels on a common 3 V to 26 V supply. Its four independent amplifiers can condition resistive, capacitive, or current-based sensors without adding four separate packages, while true differential inputs help reject signals referenced to a local sensor return. The -40°C to +105°C operating range supports controlled industrial equipment. Place each channel’s feedback network close to its input pins, and verify that the sensor signal remains within the amplifier’s input common-mode range throughout the process range.
Recomendado
ADC Input Buffering
The LM2902VDTBR2 can provide four unity-gain or modest-gain buffers between higher-impedance sensors and a multiplexed ADC input. Buffering limits ADC switching kickback at the source and allows each analog channel to retain a controlled impedance. The four-channel TSSOP reduces PCB area compared with four single amplifiers. Validate source settling, ADC acquisition time, and output drive at the selected ADC’s sample rate; the amplifier’s 40 mA per-channel rating does not replace input, output, and stability analysis for the complete interface.
Recomendado
Low-Frequency Active Filters
The LM2902VDTBR2 is suitable for first-order and basic higher-order active filters operating at low frequencies. Four channels permit implementation of a complete filter, multiple signal paths, or filter plus monitor functions in one package. Its single-supply operation is useful in 5 V or 12 V industrial systems, and true differential inputs support reference arrangements around the common ground. Select resistor and capacitor values using the manufacturer stability guidance, and keep the feedback network compact to minimize parasitic coupling and sensitivity to board contamination.
Recomendado
Audio Preamplification
The LM2902VDTBR2 can implement low-level audio preamplifier, summing, and output-buffering stages where bandwidth beyond voice-band audio is not required. Four channels allow a stereo design to use two channels for preamplification and reserve two for monitoring or active filtering. The single 3 V to 26 V supply architecture simplifies portable and industrial audio equipment. Check output swing into the intended load, input offset against the smallest signal, and input bias-current error before choosing the gain and source impedance.
Recomendado
Instrumentation and Control Loops
The LM2902VDTBR2 is appropriate for general instrumentation and control loops that require amplification of slowly varying error and feedback signals. Its four channels can provide error amplification, command scaling, actuator feedback buffering, and reference conditioning in a compact circuit. The 40 mA per-channel output capability can drive typical control interfaces within its specified limits. Confirm the common-mode range, output swing, phase margin, and capacitive-load behavior for every closed-loop configuration rather than assuming a generic compensation approach.
Recomendado
Power Supply Monitoring
The LM2902VDTBR2 can monitor up to four voltages or currents around a power system by comparing scaled sensor signals against references. The wide 3 V to 26 V operating range is useful for industrial rails, while true differential inputs simplify sensing across ground-referenced and non-ground-referenced networks. The quad package can combine rail supervision with threshold filtering or output buffering. Design the input network for the actual common-mode voltage and fault range, and ensure protection components do not inject leakage that changes the monitoring threshold.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para LM2902VDTBR2 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | LM2902DTB | LM2902DTBR2G | LM2902VDTB | LM2902DTB | LM2902DB |
|---|---|---|---|---|---|---|
| Package | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP |
| Brand | onsemi | onsemi | onsemi | onsemi | Texas Instruments | NXP Semiconductors |
| Amplifier Channels | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
Principais diferenciais
- Four general-purpose channels in one compact package (vs MC3403DR)
- Wide single-supply operating range (vs LM2902DTBR2G)
- Direct same-family footprint reuse (vs LM2902VDTB)
Notas de projeto
Place the supply bypass capacitor close to the positive supply and ground pins, with a short return path. Keep each channel’s feedback resistors close to its associated amplifier pins, and separate sensitive input traces from output traces and switching-current paths. Because all four amplifiers share common ground pins, returning large output currents through the same traces used by input references can create ground offsets that appear as signal errors.
Do not assume that identical LM2902-family packages guarantee identical electrical limits. Before substituting a part, compare input common-mode range, output swing, offset voltage, gain-bandwidth product, slew rate, supply current, output drive, and temperature grade. Also confirm the exact pin arrangement. A 14-TSSOP footprint is only the mechanical starting point; electrical compatibility and production traceability still require review.
Use the manufacturer stability and application guidance when driving capacitive loads or operating at high gain. Add isolation resistors between the amplifier output and a potentially capacitive load when required, and keep feedback-loop traces short to reduce parasitic feedback. For low-level inputs, use guarded grounding, shield against nearby switching nodes, and avoid routing the input directly beneath or beside an output pin.
Check output swing at the actual load current and supply voltage rather than using only the maximum output-current rating. The LM2902VDTBR2 can source or sink up to 40 mA per channel under specified conditions, but the usable linear swing narrows as the output approaches a supply rail. For low-voltage designs, calculate the required input level and load-current margin, then verify that the feedback configuration remains stable.
Informações de conformidade
No definitive RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified for the exact orderable MPN.