onsemi

LM2902VDTBR2 - 3-26V Quad Low-Power Op Amp | onsemi

MPN: LM2902VDTBR2 ✓ Hoạt động
3 V to 26 V Vdss 40 mA maximum Id 14-TSSOP Package
MOQ: 1 |

LM2902VDTBR2 Tóm tắt

onsemi LM2902VDTBR2 is a single-supply, low-power, general-purpose quad operational amplifier with four amplifiers in a 14-pin TSSOP package. It operates from a 3 V to 26 V supply, supports an ambient temperature range of -40°C to +105°C, and provides up to 40 mA of output current per channel. The device uses true differential inputs, allowing signals to be referenced around the supply architecture used by each amplifier.

An operational amplifier is a voltage-gain building block used in the wider semiconductor hierarchy of analog integrated circuits. It compares an inverting input with a non-inverting input and drives its output toward the difference between those voltages. Operational amplifiers support signal amplification, buffering, filtering, sensing, and closed-loop control, while the LM2902 combines four amplifiers in one package to reduce board area and simplify dual-rail or single-supply analog signal chains.

The quad configuration provides four independent amplifier channels, making LM2902VDTBR2 useful in industrial control, instrumentation, sensor interfaces, audio preamplification, and general analog processing. Its single-supply operation is particularly valuable in systems using a 3 V to 26 V rail. True differential inputs improve flexibility when the source signal is referenced to a local ground or a different point within the system rather than directly to the common supply ground.

The LM2902 family is positioned as a low-cost, low-power alternative to precision operational amplifiers. This makes it appropriate for general-purpose designs where modest offset and bandwidth are acceptable and system robustness, supply range, and channel density are more important than low-offset or high-speed performance. The four channels share a common package but retain independent input and output connections, allowing different stages to operate in the same assembly.

Typical uses include amplifying sensor outputs, buffering ADC inputs, conditioning low-frequency analog signals, implementing active filters, and providing gain stages in industrial equipment. Its 40 mA per-channel output capability is useful for moderate loads, but output drive and stability must be evaluated against the selected feedback network and load capacitance. A quad package also requires careful grounding to prevent output currents on one channel from disturbing sensitive nodes on another.

For stable operation, follow the manufacturer recommendation for bypassing the supply rail and configure compensation or feedback according to the application circuit in the LM2902 datasheet. Keep sensitive input and feedback traces away from output and supply-return paths. When replacing another amplifier, verify pin assignments, common-mode range, output swing, unity-gain stability, and load drive rather than assuming that similar voltage ratings guarantee equivalent behavior.

This product guide combines the LM2902VDTBR2 electrical limits, package information, drop-in candidates, comparison parameters, and practical PCB guidance. It highlights where a low-cost quad amplifier is suitable and where precision, high speed, low offset, rail-to-rail operation, or automotive qualification would justify a different device.

Bộ thay thế dễ dàng lắp đặt cho LM2902VDTBR2 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Các biến thể trong loạt này

Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM2902VDTBR2 (cùng hình factor và footprint) — khác nhau ở Product Type.

onsemi
Product Type: Quad operational amplifier
So sánh với LM2902VDTBR2 →

LM2902DTB

✅ Drop-In
onsemi
📦 14-TSSOP
Quad operational amplifier · onsemi · 3 V to 26 V · 4 circuits · 14-TSSOP · Surface mount · 1.2 MHz · 2 mV

Liên hệ để biết giá

Xem tài liệu →

LM2902DTBR2G

✅ Drop-In
onsemi
📦 14-TSSOP
General-purpose operational amplifier · 4 circuits · 1 MHz · 0.6 V/µs · 3 V · 32 V · 3 V to 26 V · True differential inputs

Liên hệ để biết giá

Xem tài liệu →

LM2902VDTB

✅ Drop-In
onsemi
📦 14-TSSOP
4 circuits · 3 V to 26 V · Low power · True differential inputs · 14-TSSOP · Surface mount · General-purpose operational amplifier · 4

Liên hệ để biết giá

Xem tài liệu →

LM2902DTB

✅ Drop-In
onsemi
📦 14-TSSOP
Quad operational amplifier · onsemi · 3 V to 26 V · 4 circuits · 14-TSSOP · Surface mount · 1.2 MHz · 2 mV

Liên hệ để biết giá

Xem tài liệu →

LM2902DB

✅ Drop-In
📦 14-TSSOP
Same 14-TSSOP quad-amplifier footprint and single-supply architecture; manufacturer-specific common-mode and offset limits require verification.

📋 Tham chiếu thay thế (không có trong danh mục)

LM2902VDTBR2 Tỷ lệ tối đa & tính chất điện

Product Type Single-supply quad operational amplifier
Number of Amplifier Channels 4 circuits
Supply Voltage Range 3 V to 26 V
Khoảng nhiệt độ hoạt động -40°C to +105°C
Output Current per Channel 40 mA maximum
Input Bias Current 90 nA maximum
Differential Input True differential input
Package Type 14-TSSOP
Package Pin Count 14 pins
Package Width 4.40 mm
Package Width Alternate Value 0.173 inch
Kiểu lắp đặt Surface mount
Số lượng đầu ra 4 outputs
Number of Input Pairs 4 input pairs
Trạng thái RoHS unknown
REACH Status unknown
AEC-Q100 Qualification unknown

Cấu hình chân LM2902VDTBR2

TSSOP-14 (4.4mm) Package Pinout Diagram TSSOP-14 4.4x5mm, P0.65mm, JEDEC MO-153. 14-pin thin shrink. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 TSSOP-14 (4.4mm)
Chân 1 OUT1 — Amplifier 1 output
Chân 2 IN1- — Amplifier 1 inverting input
Chân 3 IN1+ — Amplifier 1 non-inverting input
Chân 4 GND — Common ground connection
Chân 5 IN2+ — Amplifier 2 non-inverting input
Chân 6 IN2- — Amplifier 2 inverting input
Chân 7 OUT2 — Amplifier 2 output
Chân 8 OUT3 — Amplifier 3 output
Chân 9 IN3- — Amplifier 3 inverting input
Chân 10 IN3+ — Amplifier 3 non-inverting input
Chân 11 GND — Common ground connection
Chân 12 IN4+ — Amplifier 4 non-inverting input
Chân 13 IN4- — Amplifier 4 inverting input
Chân 14 OUT4 — Amplifier 4 output

Ứng dụng tiêu biểu

LM2902VDTBR2 phù hợp cho 6 Áp dụngs: Industrial Sensor Signal Conditioning, ADC Input Buffering, Low-Frequency Active Filters, Audio Preamplification, Instrumentation and Control Loops, Power Supply Monitoring.

🏭

Industrial Sensor Signal Conditioning

The LM2902VDTBR2 fits industrial sensor interfaces that require several amplified channels on a common 3 V to 26 V supply. Its four independent amplifiers can condition resistive, capacitive, or current-based sensors without adding four separate packages, while true differential inputs help reject signals referenced to a local sensor return. The -40°C to +105°C operating range supports controlled industrial equipment. Place each channel’s feedback network close to its input pins, and verify that the sensor signal remains within the amplifier’s input common-mode range throughout the process range.

📊

ADC Input Buffering

The LM2902VDTBR2 can provide four unity-gain or modest-gain buffers between higher-impedance sensors and a multiplexed ADC input. Buffering limits ADC switching kickback at the source and allows each analog channel to retain a controlled impedance. The four-channel TSSOP reduces PCB area compared with four single amplifiers. Validate source settling, ADC acquisition time, and output drive at the selected ADC’s sample rate; the amplifier’s 40 mA per-channel rating does not replace input, output, and stability analysis for the complete interface.

⚡

Low-Frequency Active Filters

The LM2902VDTBR2 is suitable for first-order and basic higher-order active filters operating at low frequencies. Four channels permit implementation of a complete filter, multiple signal paths, or filter plus monitor functions in one package. Its single-supply operation is useful in 5 V or 12 V industrial systems, and true differential inputs support reference arrangements around the common ground. Select resistor and capacitor values using the manufacturer stability guidance, and keep the feedback network compact to minimize parasitic coupling and sensitivity to board contamination.

🎧

Audio Preamplification

The LM2902VDTBR2 can implement low-level audio preamplifier, summing, and output-buffering stages where bandwidth beyond voice-band audio is not required. Four channels allow a stereo design to use two channels for preamplification and reserve two for monitoring or active filtering. The single 3 V to 26 V supply architecture simplifies portable and industrial audio equipment. Check output swing into the intended load, input offset against the smallest signal, and input bias-current error before choosing the gain and source impedance.

🔧

Instrumentation and Control Loops

The LM2902VDTBR2 is appropriate for general instrumentation and control loops that require amplification of slowly varying error and feedback signals. Its four channels can provide error amplification, command scaling, actuator feedback buffering, and reference conditioning in a compact circuit. The 40 mA per-channel output capability can drive typical control interfaces within its specified limits. Confirm the common-mode range, output swing, phase margin, and capacitive-load behavior for every closed-loop configuration rather than assuming a generic compensation approach.

🔋

Power Supply Monitoring

The LM2902VDTBR2 can monitor up to four voltages or currents around a power system by comparing scaled sensor signals against references. The wide 3 V to 26 V operating range is useful for industrial rails, while true differential inputs simplify sensing across ground-referenced and non-ground-referenced networks. The quad package can combine rail supervision with threshold filtering or output buffering. Design the input network for the actual common-mode voltage and fault range, and ensure protection components do not inject leakage that changes the monitoring threshold.

What is the LM2902VDTBR2?
The LM2902VDTBR2 is a four-channel, single-supply operational amplifier from onsemi packaged in a 14-pin TSSOP. It operates from 3 V to 26 V and is intended for general-purpose amplification, buffering, filtering, and sensor-signal conditioning. The manufacturer datasheet identifies the device as part of the low-cost, low-power quad operational-amplifier family with true differential inputs.
What is the supply voltage range of LM2902VDTBR2?
The LM2902VDTBR2 operates from a 3 V to 26 V single supply. According to the onsemi product description, this range supports both low-voltage embedded systems and higher-voltage industrial analog circuits. The complete electrical limits and operating conditions should be checked in the manufacturer datasheet before using the amplifier near either supply limit.
What is the operating temperature range of LM2902VDTBR2?
The LM2902VDTBR2 is specified for an ambient operating range of -40°C to +105°C. This broad industrial-temperature range supports equipment expected to operate in controlled indoor systems, vehicles, and industrial environments. Keep the complete device within its specified supply and common-mode limits because the temperature rating alone does not guarantee correct amplification.
Where can I download the LM2902VDTBR2 datasheet PDF?
The LM2902VDTBR2 datasheet is available from onsemi through the LM2902 family documentation. Use the manufacturer PDF linked on this page and consult the pin-description table, electrical characteristics, typical application circuits, and ordering information. The part number is a specific 14-TSSOP orderable variant within the broader LM2902 and LM324 operating-amplifier family.
Where can I find the LM2902VDTBR2 pinout?
The LM2902VDTBR2 pinout is shown in the manufacturer datasheet pin-configuration diagram. The 14-pin TSSOP contains four complete operational-amplifier channels: four non-inverting inputs, four inverting inputs, four outputs, and two common ground pins. Use the numbered package drawing when assigning PCB nets because alternative amplifier families may arrange equivalent channels differently.
How many amplifiers are in the LM2902VDTBR2?
The LM2902VDTBR2 contains four independent operational-amplifier channels. Each channel has its own non-inverting input, inverting input, and output, while two pins provide common ground. Integrating four amplifiers into one 14-pin TSSOP can reduce board area and simplify designs containing several gain, buffer, or filtering stages.
Is the LM2902VDTBR2 suitable for single-supply operation?
Yes, the LM2902VDTBR2 is designed for single-supply operation from 3 V to 26 V. Its true differential inputs provide flexibility when the signal reference is not tied directly to the common ground pin. As with any non-rail-to-rail amplifier, confirm the input common-mode range and output swing against the actual signal and load before finalizing the design.
What is the output current capability of LM2902VDTBR2?
The LM2902VDTBR2 can provide up to 40 mA per output channel according to its published product characteristics. This is sufficient for typical high-impedance sensor and feedback-network applications, but output current does not guarantee stable operation with every capacitive load. Use the manufacturer application guidance when driving cables, ADC inputs, or other low-impedance loads.
What can replace the LM2902VDTBR2?
Several LM2902-family devices in the 14-TSSOP footprint can serve as pin-compatible candidates, but replacement requires checking the exact pin assignments and electrical limits. The listed drop-in options include same-package onsemi and Texas Instruments variants and an NXP TSSOP option. Final substitution should also account for supply range, temperature grade, offset, bandwidth, and qualification requirements.
What is the best drop-in replacement for LM2902VDTBR2?
LM2902DTB from onsemi is a direct same-family 14-TSSOP drop-in candidate for LM2902VDTBR2 because the comparison identifies consistent terminals, package, and principal functional characteristics. It remains important to review markings, orderable suffix, temperature range, and purchasing traceability. A footprint match alone does not guarantee identical production or qualification status.
Is LM2902VDTBR2 the same as LM2902DTB?
LM2902DTB and LM2902VDTBR2 are closely related LM2902-family quad operational amplifiers in a 14-pin TSSOP package, and the available comparison identifies LM2902DTB as a complete replacement without requiring terminal or package changes. Orderable suffixes can still indicate differences in grade, packaging, or production conditions, so confirm the final manufacturer part number before substitution.
LM2902VDTBR2 vs LM2902DTB: which is better for an industrial design?
LM2902DTB is the stronger drop-in choice when the goal is to reproduce a 14-TSSOP LM2902 design without changing the footprint, because the available comparison reports consistent terminals and package. LM2902VDTBR2 remains appropriate when its exact orderable qualification and supply status are required. For industrial use, also verify -40°C to +105°C operation and any additional assembly or qualification requirements.
When should I choose LM2902VDTBR2 instead of a precision op amp?
Choose LM2902VDTBR2 when four general-purpose channels, a 3 V to 26 V single supply, and low system cost matter more than low offset or high precision. It is suitable for moderate-gain signal conditioning and buffering where its input offset and bandwidth are acceptable. Choose a precision amplifier when sensor accuracy, offset matching, or low-level error dominates the application requirements.
Is LM2902VDTBR2 in stock and what is its lead time?
Current stock quantity and production lead time for LM2902VDTBR2 should be confirmed through the Request a Quote form on this page. The form allows the exact MPN, target quantity, and delivery requirements to be reviewed without relying on changing inventory figures. Order quantity and packaging selection can also affect the quoted lead time.
Where can I buy LM2902VDTBR2 online?
Use the Request a Quote form on this page to request LM2902VDTBR2 with the required quantity and delivery terms. Provide the exact 14-TSSOP orderable MPN when submitting the request. Current availability and lead time are confirmed as part of the quotation rather than published as static figures that can quickly become outdated.
What are the key specifications of LM2902VDTBR2?
The key specifications are four amplifier channels, a 3 V to 26 V single-supply range, true differential inputs, and an operating temperature range of -40°C to +105°C. The onsemi product data also identifies a 14-TSSOP package and up to 40 mA output current per channel. Gain-bandwidth, offset, slew rate, and detailed common-mode limits must be selected from the manufacturer electrical-characteristics table for the exact orderable device.

Dữ liệu tham khảo kỹ thuật cho LM2902VDTBR2 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose LM2902VDTBR2 for a general-purpose four-channel analog design that operates from a 3 V to 26 V single supply and fits the -40°C to +105°C range. LM2902DTB from onsemi is a practical same-brand drop-in when the orderable suffix and production requirements permit; LM2902VDTB is also a footprint-compatible same-family option. Texas Instruments LM2902DTB can suit designs where its manufacturer-specific offset and offset-drift characteristics are acceptable, while NXP LM2902DB requires careful review of common-mode range, bandwidth, and qualification. Prefer a precision op amp when low offset dominates the signal chain, and choose a rail-to-rail device when the signal or output must operate close to the supply rails. This quad amplifier is best when integrating four modest-bandwidth stages saves more PCB area and inventory complexity than precision or high-speed performance matters.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này LM2902DTB LM2902DTBR2G LM2902VDTB LM2902DTB LM2902DB
Package 14-TSSOP 14-TSSOP 14-TSSOP 14-TSSOP 14-TSSOP 14-TSSOP
Brand onsemi onsemi onsemi onsemi Texas Instruments NXP Semiconductors
Amplifier Channels 4 circuits 4 circuits 4 circuits 4 circuits 4 circuits 4 circuits

Bảo phân biệt quan trọng

  • Four general-purpose channels in one compact package (vsMC3403DR)
  • Wide single-supply operating range (vsLM2902DTBR2G)
  • Direct same-family footprint reuse (vsLM2902VDTB)

Ghi chú thiết kế

Place the supply bypass capacitor close to the positive supply and ground pins, with a short return path. Keep each channel’s feedback resistors close to its associated amplifier pins, and separate sensitive input traces from output traces and switching-current paths. Because all four amplifiers share common ground pins, returning large output currents through the same traces used by input references can create ground offsets that appear as signal errors.

Do not assume that identical LM2902-family packages guarantee identical electrical limits. Before substituting a part, compare input common-mode range, output swing, offset voltage, gain-bandwidth product, slew rate, supply current, output drive, and temperature grade. Also confirm the exact pin arrangement. A 14-TSSOP footprint is only the mechanical starting point; electrical compatibility and production traceability still require review.

Use the manufacturer stability and application guidance when driving capacitive loads or operating at high gain. Add isolation resistors between the amplifier output and a potentially capacitive load when required, and keep feedback-loop traces short to reduce parasitic feedback. For low-level inputs, use guarded grounding, shield against nearby switching nodes, and avoid routing the input directly beneath or beside an output pin.

Check output swing at the actual load current and supply voltage rather than using only the maximum output-current rating. The LM2902VDTBR2 can source or sink up to 40 mA per channel under specified conditions, but the usable linear swing narrows as the output approaches a supply rail. For low-voltage designs, calculate the required input level and load-current margin, then verify that the feedback configuration remains stable.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

No definitive RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified for the exact orderable MPN.

Dữ liệu được xác minh vào: 2026-11-09 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

LM2902VDTBR2 datasheet LM2902VDTBR2 specifications LM2902VDTBR2 pinout LM2902VDTBR2 datasheet pdf LM2902VDTBR2 equivalent LM2902VDTBR2 replacement LM2902VDTBR2 cross reference LM2902VDTBR2 price LM2902VDTBR2 stock onsemi LM2902VDTBR2 LM2902VDTBR2 14-TSSOP pinout LM2902VDTBR2 application circuit LM2902VDTBR2 vs LM2902DTB LM2902VDTBR2 amplifier footprint

Các bộ phận và thuật ngữ liên quan

onsemi LM2902VDTBR2 LM2902DTB LM2902DTBR2G LM2902VDTB Texas Instruments NXP Semiconductors quad operational amplifier operational amplifier analog integrated circuit single-supply amplifier true differential input inverting input non-inverting input output current common-mode input range input offset voltage gain-bandwidth product TSSOP-14 14-TSSOP surface-mount package sensor signal conditioning active filter ADC input buffering industrial control
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ