LM2904WYDT - Low-Power Dual Op Amp, 3-30V | STMicroelectronics
N.º da peça: LM2904WYDT ✓ AtivoLM2904WYDT Visão geral
An operational amplifier is an analog signal-processing IC that uses high-gain differential amplification to compare or condition voltages. The LM2904 belongs to the dual general-purpose operational-amplifier category, combining two amplifier channels in one compact package. Its wide supply range makes it suitable for systems powered from industrial 24 V rails, split analog supplies, or lower-voltage circuits when the operating limits are respected.
Key characteristics include two amplifier circuits with single-ended outputs, a 1.1 MHz gain-bandwidth product, operation across a 3 V to 30 V supply range, and a common 100 dB figure cited for the family. These characteristics support general-purpose signal conditioning, low-frequency amplification, feedback-based control, and analog sensor interfaces where a precision rail-to-rail amplifier is unnecessary.
The LM2904 architecture is designed for dependable operation from conventional dual supplies, including positive and negative rails. Designers should verify input and output voltage limits, common-mode range, output-current capability, and stability requirements against the manufacturer datasheet for the selected operating condition. The two channels share a supply but otherwise operate independently.
Typical uses include industrial sensor conditioning, audio preamplification, motor and actuator interfaces, current-loop signal processing, sample-and-hold circuits, and general DC signal amplification. The 1.1 MHz bandwidth is appropriate for low-frequency control and analog conditioning rather than high-speed video or RF signal chains.
Decoupling remains important in precision analog systems. Place a suitable bypass capacitor close to each supply pin and keep feedback components and sensitive input traces away from switching nodes. Account for input bias current, input offset voltage, output swing, and load-capacitance stability when selecting external components.
This product overview consolidates the exact LM2904WYDT package, electrical characteristics, sourcing terms, comparison parameters, and practical design guidance. It also identifies same-footprint family alternatives so engineers can assess temperature-grade, revision, and sourcing differences before approving a replacement.
Alternativas drop-in para LM2904WYDT — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com LM2904WYDT (mesmo formato e footprint) — diferindo em Amplifier Type, Package, Number of Channels.
LM2904YDT
✅ Drop-In ⚠️ Especificações não verificadasConsulte o preço
Ver ficha técnica →LM2904WDT
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
LM2904DT
✅ Drop-In ⚠️ Especificações não verificadasConsulte o preço
Ver ficha técnica →LM2904BDT
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
LM2904BYDT
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
LM2904WYDT Classificações máximas e características elétricas
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Channels | 2 channels |
| Supply Voltage Range | 3 V to 30 V |
| Gain-Bandwidth Product | 1.1 MHz |
| Tipo de saída | Single-ended |
| Low-Power Classification | Low power |
| Common-Mode Rejection | 100 dB |
| Encapsulamento | 8-SOIC, 3.90 mm body width |
| Tipo de montagem | Surface mount |
Configuração de pinos do LM2904WYDT
| Pino 1 | OUTA — Amplifier A output |
| Pino 2 | IN A- — Inverting input for amplifier A |
| Pino 3 | IN A+ — Non-inverting input for amplifier A |
| Pino 4 | V- — Negative supply voltage |
| Pino 5 | IN B+ — Non-inverting input for amplifier B |
| Pino 6 | IN B- — Inverting input for amplifier B |
| Pino 7 | OUTB — Amplifier B output |
| Pino 8 | V+ — Positive supply voltage |
Aplicações típicas
LM2904WYDT é adequado para 6 aplicaçãos: Industrial Sensor Signal Conditioning, Audio Preamplification, Motor and Actuator Control, Current-Loop Signal Processing, Data Acquisition and Analog Filtering, Portable and Battery-Powered Interfaces.
Industrial Sensor Signal Conditioning
The LM2904WYDT fits low-frequency industrial sensor conditioning because its two channels can amplify differential sensor signals while operating from a supply between 3 V and 30 V. The 100 dB common-mode rejection helps suppress common-mode disturbance when the sensor signal is small relative to the surrounding industrial noise environment. Its 1.1 MHz gain-bandwidth product supports closed-loop gains suitable for pressure, temperature, and position-sensor interfaces, while the 8-SOIC package simplifies dual-channel routing. The design must still verify input bias current, input offset voltage, common-mode range, and output swing against the sensor impedance and selected supply.
Recomendado
Audio Preamplification
The LM2904WYDT can serve as a dual audio preamplifier for low-frequency source signals in consumer, communications, or industrial audio equipment. Each channel may provide voltage gain around a source or active sensor, and the 1.1 MHz gain-bandwidth product is sufficient for voice-band and many general audio-conditioning tasks. The 3 V to 30 V supply range allows operation from modest single supplies or conventional split rails. Headroom and distortion checks are essential because output swing, output-current capability, noise, and channel-to-channel behavior depend on the supply and load. Decoupling and feedback-component selection should follow the manufacturer application guidance.
Recomendado
Motor and Actuator Control
The LM2904WYDT is suitable for low-frequency actuator feedback and control-loop stages where the amplifier operates close to the power circuitry. Its dual-channel configuration supports independent error and drive-related amplification, while the wide 3 V to 30 V supply range can simplify interface design around 24 V industrial systems. The 1.1 MHz bandwidth provides ample response for many slow position, current, or voltage loops, but it is not intended for high-bandwidth motor switching waveforms. Place the device away from switching nodes, use a clean local supply reference, and verify common-mode voltage and output swing at every operating state.
Recomendado
Current-Loop Signal Processing
The LM2904WYDT can process the voltage produced by a current sensor when the application does not require a dedicated instrumentation amplifier. Two independent channels can handle complementary measurements or perform gain and filtering functions. The 100 dB common-mode rejection provides useful rejection of common-mode voltage, while the 1.1 MHz gain-bandwidth product supports moderate-bandwidth feedback networks. Performance still depends on sensor impedance, source noise, offset stability, and resistor matching. For high-impedance or precision current measurement, compare the complete input-stage specification and use gain-setting resistors with suitable tolerance and temperature behavior.
Recomendado
Data Acquisition and Analog Filtering
The LM2904WYDT can implement active filters and analog front-end stages in low-speed data-acquisition systems. Its 1.1 MHz gain-bandwidth product supports common low-frequency filter topologies, and the dual arrangement can form a two-channel gain or filtering path. The 3 V to 30 V supply range offers flexibility across compact and industrial systems. Component tolerances, input bias current, output loading, and amplifier stability remain central design considerations, particularly when the signal source has high output impedance. Keep sensitive nodes compact, maintain short feedback paths, and follow the manufacturer’s recommended compensation network when driving capacitive loads.
Recomendado
Portable and Battery-Powered Interfaces
The LM2904WYDT can be used in low-power interface circuits where the actual operating point falls within its 3 V to 30 V supply capability. The low-power dual-amplifier format consolidates two signal-conditioning paths in an 8-SOIC package, while the 1.1 MHz gain-bandwidth product is appropriate for many sensor, control, and monitoring signals. Battery-powered operation requires an explicit current budget because bias current and quiescent consumption depend on supply voltage and the selected device revision. Use the manufacturer electrical characteristics to estimate average and peak consumption, then confirm input common-mode range and output swing for the battery’s loaded voltage range.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para LM2904WYDT — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | LM2904YDT | LM2904WDT | LM2904DT | LM2904BDT | LM2904BYDT |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 8-SOIC | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same |
| Amplifier Configuration | Dual, 2 channels | Dual, 2 channels | Dual, 2 channels | Dual, 2 channels | Dual, 2 channels | Dual, 2 channels |
| Supply Voltage Range | 3 V to 30 V | 3 V to 30 V | 3 V to 30 V | 3 V to 30 V | 3 V to 30 V | 3 V to 30 V |
| Gain-Bandwidth Product | 1.1 MHz | 1.1 MHz | 1.1 MHz | 1.1 MHz | 1.1 MHz | 1.1 MHz |
| Output Type | Single-ended | Single-ended | Single-ended | Single-ended | Single-ended | Single-ended |
| Power Classification | Low power | Low power | Low power | Low power | Low power | Low power |
| Orderable Grade or Revision | LM2904WYDT | LM2904 Y grade | LM2904 W grade | LM2904 standard orderable suffix | LM2904 B revision | LM2904 B revision with Y grade |
Principais diferenciais
- Two independent general-purpose channels in one compact package (vs LM2902MTX)
- Wide supply range for industrial interface designs (vs LM2904WDT)
- Defined single-ended output architecture (vs LM2904DT)
- Common-mode rejection for differential signal conditioning (vs LM2904BDT)
Notas de projeto
Confirm the actual positive and negative rail magnitudes against the 3 V to 30 V supply limit. In a split-supply circuit, the total rail-to-rail voltage must remain below 30 V even during transient excursions. Place the bypass capacitor close to the V+ pin and return its ground end directly to the V- reference plane. The two channels share the same supply pins, so their total supply-current demand must be included in the regulator and thermal budget.
Route each non-inverting input directly to its source and keep the inverting-input feedback loop short and compact. Sensitive input traces should remain away from switching-node copper, high-current motor paths, and inductors. Connect the two supply pins to a low-impedance plane and use a local bypass capacitor so transient current does not travel through long traces. Pin 1 should be identified correctly on the 8-SOIC footprint to avoid reversing the two amplifier channels.
Do not assume that the 3 V to 30 V supply rating permits operation with every input signal at those voltages. Check the input common-mode range and output swing in the STMicroelectronics manufacturer datasheet for the actual supply. Also verify the source impedance, because input bias current can create offset error in high-impedance circuits, and add isolation when driving capacitive loads if the selected revision requires it.
Informações de conformidade
The exact LM2904WYDT compliance status requires confirmation from the current STMicroelectronics product declaration or manufacturer ordering documentation.