STMicroelectronics

LM2904WYDT - Low-Power Dual Op Amp, 3-30V | STMicroelectronics

MPN: LM2904WYDT ✓ فعال
3 V to 30 V Vdss 8-SOIC, 3.90 mm body width Package
MOQ: 1 |

LM2904WYDT جائزہ

STMicroelectronics LM2904WYDT is a low-power dual operational amplifier with two independent amplifiers, a 3 V to 30 V supply range, and a gain-bandwidth product of 1.1 MHz. The device is supplied in an 8-SOIC package configured for industrial temperature-grade operation.

An operational amplifier is an analog signal-processing IC that uses high-gain differential amplification to compare or condition voltages. The LM2904 belongs to the dual general-purpose operational-amplifier category, combining two amplifier channels in one compact package. Its wide supply range makes it suitable for systems powered from industrial 24 V rails, split analog supplies, or lower-voltage circuits when the operating limits are respected.

Key characteristics include two amplifier circuits with single-ended outputs, a 1.1 MHz gain-bandwidth product, operation across a 3 V to 30 V supply range, and a common 100 dB figure cited for the family. These characteristics support general-purpose signal conditioning, low-frequency amplification, feedback-based control, and analog sensor interfaces where a precision rail-to-rail amplifier is unnecessary.

The LM2904 architecture is designed for dependable operation from conventional dual supplies, including positive and negative rails. Designers should verify input and output voltage limits, common-mode range, output-current capability, and stability requirements against the manufacturer datasheet for the selected operating condition. The two channels share a supply but otherwise operate independently.

Typical uses include industrial sensor conditioning, audio preamplification, motor and actuator interfaces, current-loop signal processing, sample-and-hold circuits, and general DC signal amplification. The 1.1 MHz bandwidth is appropriate for low-frequency control and analog conditioning rather than high-speed video or RF signal chains.

Decoupling remains important in precision analog systems. Place a suitable bypass capacitor close to each supply pin and keep feedback components and sensitive input traces away from switching nodes. Account for input bias current, input offset voltage, output swing, and load-capacitance stability when selecting external components.

This product overview consolidates the exact LM2904WYDT package, electrical characteristics, sourcing terms, comparison parameters, and practical design guidance. It also identifies same-footprint family alternatives so engineers can assess temperature-grade, revision, and sourcing differences before approving a replacement.

کے لیے ڈراپ اِن متبادل LM2904WYDT — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

اس سیریز میں مختلف ورژن

اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں LM2904WYDT (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Amplifier Type, Package, Number of Channels.

STMicroelectronics
Amplifier Type: Standard (General Purpose)
Package: SOIC-8 (8-SOIC / SOP-8)
Number of Channels: 2
موازنہ کریں LM2904WYDT →
STMicroelectronics
Amplifier Type: General-purpose operational amplifier
Package: 8-SOIC
موازنہ کریں LM2904WYDT →

LM2904YDT

✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ
STMicroelectronics
📦 8-SOIC
General-purpose operational amplifier · 2 channels · 2 circuits · Dual independent operational amplifier · Low-power · 30 V · 0.6 V/µs · Single-ended

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

LM2904WDT

✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ
📦 8-SOIC
Same 8-SOIC dual-amplifier pinout and 3 V to 30 V supply capability; the standard-temperature orderable grade differs from LM2904WYDT by approximately 20 C of temperature coverage.

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

LM2904DT

✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ
STMicroelectronics
📦 8-SOIC
2 · 2 · Standard (General Purpose) · Single-Ended · High gain, internally frequency-compensated · 1.1 MHz · 15 V

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

LM2904BDT

✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ
📦 8-SOIC
Same 8-SOIC LM2904-family pin arrangement and 3 V to 30 V supply range; the B-family revision changes internal characteristics while retaining the core 1.1 MHz bandwidth class.

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

LM2904BYDT

✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ
📦 8-SOIC
Same 8-SOIC LM2904-family footprint and dual-amplifier topology; B-family revision and orderable-grade coding differ while the 3 V to 30 V supply capability remains unchanged.

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

LM2904WYDT زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات

Amplifier Type Dual general-purpose operational amplifier
Number of Channels 2 channels
Supply Voltage Range 3 V to 30 V
Gain-Bandwidth Product 1.1 MHz
آؤٹ پٹ کی قسم Single-ended
Low-Power Classification Low power
Common-Mode Rejection 100 dB
پیکیج 8-SOIC, 3.90 mm body width
ماؤنٹنگ ٹائپ Surface mount

LM2904WYDT پن کنفیگریشن

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
پن 1 OUTA — Amplifier A output
پن 2 IN A- — Inverting input for amplifier A
پن 3 IN A+ — Non-inverting input for amplifier A
پن 4 V- — Negative supply voltage
پن 5 IN B+ — Non-inverting input for amplifier B
پن 6 IN B- — Inverting input for amplifier B
پن 7 OUTB — Amplifier B output
پن 8 V+ — Positive supply voltage

عام استعمالات

LM2904WYDT کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Sensor Signal Conditioning, Audio Preamplification, Motor and Actuator Control, Current-Loop Signal Processing, Data Acquisition and Analog Filtering, Portable and Battery-Powered Interfaces.

🏭

Industrial Sensor Signal Conditioning

The LM2904WYDT fits low-frequency industrial sensor conditioning because its two channels can amplify differential sensor signals while operating from a supply between 3 V and 30 V. The 100 dB common-mode rejection helps suppress common-mode disturbance when the sensor signal is small relative to the surrounding industrial noise environment. Its 1.1 MHz gain-bandwidth product supports closed-loop gains suitable for pressure, temperature, and position-sensor interfaces, while the 8-SOIC package simplifies dual-channel routing. The design must still verify input bias current, input offset voltage, common-mode range, and output swing against the sensor impedance and selected supply.

🎧

Audio Preamplification

The LM2904WYDT can serve as a dual audio preamplifier for low-frequency source signals in consumer, communications, or industrial audio equipment. Each channel may provide voltage gain around a source or active sensor, and the 1.1 MHz gain-bandwidth product is sufficient for voice-band and many general audio-conditioning tasks. The 3 V to 30 V supply range allows operation from modest single supplies or conventional split rails. Headroom and distortion checks are essential because output swing, output-current capability, noise, and channel-to-channel behavior depend on the supply and load. Decoupling and feedback-component selection should follow the manufacturer application guidance.

⚡

Motor and Actuator Control

The LM2904WYDT is suitable for low-frequency actuator feedback and control-loop stages where the amplifier operates close to the power circuitry. Its dual-channel configuration supports independent error and drive-related amplification, while the wide 3 V to 30 V supply range can simplify interface design around 24 V industrial systems. The 1.1 MHz bandwidth provides ample response for many slow position, current, or voltage loops, but it is not intended for high-bandwidth motor switching waveforms. Place the device away from switching nodes, use a clean local supply reference, and verify common-mode voltage and output swing at every operating state.

🔧

Current-Loop Signal Processing

The LM2904WYDT can process the voltage produced by a current sensor when the application does not require a dedicated instrumentation amplifier. Two independent channels can handle complementary measurements or perform gain and filtering functions. The 100 dB common-mode rejection provides useful rejection of common-mode voltage, while the 1.1 MHz gain-bandwidth product supports moderate-bandwidth feedback networks. Performance still depends on sensor impedance, source noise, offset stability, and resistor matching. For high-impedance or precision current measurement, compare the complete input-stage specification and use gain-setting resistors with suitable tolerance and temperature behavior.

📺

Data Acquisition and Analog Filtering

The LM2904WYDT can implement active filters and analog front-end stages in low-speed data-acquisition systems. Its 1.1 MHz gain-bandwidth product supports common low-frequency filter topologies, and the dual arrangement can form a two-channel gain or filtering path. The 3 V to 30 V supply range offers flexibility across compact and industrial systems. Component tolerances, input bias current, output loading, and amplifier stability remain central design considerations, particularly when the signal source has high output impedance. Keep sensitive nodes compact, maintain short feedback paths, and follow the manufacturer’s recommended compensation network when driving capacitive loads.

📱

Portable and Battery-Powered Interfaces

The LM2904WYDT can be used in low-power interface circuits where the actual operating point falls within its 3 V to 30 V supply capability. The low-power dual-amplifier format consolidates two signal-conditioning paths in an 8-SOIC package, while the 1.1 MHz gain-bandwidth product is appropriate for many sensor, control, and monitoring signals. Battery-powered operation requires an explicit current budget because bias current and quiescent consumption depend on supply voltage and the selected device revision. Use the manufacturer electrical characteristics to estimate average and peak consumption, then confirm input common-mode range and output swing for the battery’s loaded voltage range.

What is the LM2904WYDT?
The LM2904WYDT is a STMicroelectronics low-power dual general-purpose operational amplifier supplied in an 8-SOIC package. It contains two independent amplifier channels with single-ended outputs, accepts a 3 V to 30 V supply, and has a gain-bandwidth product of 1.1 MHz. According to the manufacturer datasheet, the device is intended for general-purpose low-frequency amplification and signal conditioning rather than precision or high-speed applications.
What is the operating voltage of LM2904WYDT?
The LM2904WYDT operates from a 3 V minimum supply to a 30 V maximum supply. According to the STMicroelectronics manufacturer datasheet, the actual signal input and output voltages must also remain inside the common-mode and output-swing limits for the selected supply. The 30 V maximum is a total supply constraint, so check that the sum of positive and negative rail magnitudes does not exceed it in split-supply circuits.
What are the key specifications of LM2904WYDT that engineers should know?
The LM2904WYDT combines two independent operational-amplifier channels, a 3 V to 30 V supply range, a 1.1 MHz gain-bandwidth product, and single-ended outputs in an 8-SOIC package. The STMicroelectronics manufacturer datasheet also identifies the device as a low-power, general-purpose amplifier and cites 100 dB common-mode rejection. Input offset, bias current, slew rate, and output-current limits require separate review for precision or high-loading designs.
Where to download the LM2904WYDT datasheet PDF?
Download the LM2904WYDT documentation from the STMicroelectronics product resources or the official datasheet link on this page. The manufacturer datasheet is the controlling document for the pin description, electrical limits, application circuit, and ordering information. The product is also identified as a low-power dual operational amplifier in distributor documentation, but the manufacturer document should be used for design qualification.
Where can I find the LM2904WYDT pinout?
The LM2904WYDT pinout is documented in the STMicroelectronics manufacturer datasheet and uses an 8-SOIC arrangement. Pins 1 and 7 are the two amplifier outputs, pins 2 and 6 are the inverting inputs, pins 3 and 5 are the non-inverting inputs, pin 4 is the negative supply, and pin 8 is the positive supply. Use the pin-description table in the manufacturer document when assigning PCB tracks.
Is LM2904WYDT suitable for sensor signal conditioning?
Yes, the LM2904WYDT is suitable for many low-frequency sensor-conditioning applications because it provides two channels, accepts a 3 V to 30 V supply, and has a 1.1 MHz gain-bandwidth product. Its 100 dB common-mode rejection helps reject equal-magnitude noise on differential inputs. The STMicroelectronics manufacturer datasheet should be checked for input bias current, offset voltage, common-mode range, and output swing before selecting the external gain network.
LM2904WYDT vs LM2904YDT - which is better for industrial use?
Choose LM2904WYDT when its specified temperature grade and tape-and-reel presentation match the assembly process; choose LM2904YDT when that non-reel ordering option is preferred. Both are 8-SOIC LM2904-family devices, but the orderable suffix determines the delivery and temperature-grade coding. The STMicroelectronics manufacturer datasheet and ordering table control the exact grade and operating limits for each suffix.
Can LM2904YDT replace LM2904WYDT on the same PCB?
The LM2904YDT can be evaluated as a pin-compatible LM2904-family replacement because it uses the same 8-SOIC amplifier arrangement and dual general-purpose topology. Confirm the required temperature grade, package orientation, production form, and electrical limits in the STMicroelectronics ordering documentation before substitution. PCB changes are not normally required, provided the supply, common-mode, output-swing, and stability requirements remain satisfied.
What can replace LM2904WYDT?
The closest replacements are the pin-compatible LM2904-family devices in the 8-SOIC package, including LM2904YDT, LM2904WDT, LM2904DT, LM2904BDT, and LM2904BYDT. Their practical differences concern orderable temperature grades, package presentation, and later-family revisions rather than the basic dual-amplifier function. Select the exact replacement after checking the manufacturer ordering information against the required temperature range and assembly method.
Is LM2904WYDT the same as LM2904DT?
The LM2904WYDT and LM2904DT are not interchangeable as identical orderable MPNs because their suffixes encode different ordering conditions, but both belong to the LM2904 family and use an 8-SOIC implementation. According to STMicroelectronics documentation, the device function and channel arrangement are comparable. Confirm temperature grade, reel or tube presentation, and the latest electrical limits before treating either suffix as a procurement substitute.
When should I choose LM2904WYDT over LM2904BDT?
Choose LM2904WYDT when the design and assembly process are tied to that exact orderable device and its specified operating grade. Choose LM2904BDT when the later B-family revision offers the electrical or documentation changes required by the application while retaining the same 8-SOIC footprint. Compare offset voltage, bias current, slew behavior, and temperature limits in the manufacturer datasheet rather than selecting only by family name.
Is LM2904WYDT in stock?
Stock status for LM2904WYDT can change rapidly and is not represented as a fixed product attribute. Use the Request a Quote form on this page to request current availability, lot information, and lead time for the exact MPN. The manufacturer ordering code and package form should also be confirmed before a purchase order is released.
What is the price of LM2904WYDT?
Current pricing for LM2904WYDT should be requested through the Request a Quote form on this page so the result reflects the exact suffix, quantity, and current supply position. The part is an 8-SOIC dual operational amplifier, and package form or grade can affect procurement. Avoid substituting a quote for a different LM2904 suffix because the ordering codes are not fully interchangeable.
What is the lead time for LM2904WYDT?
The current lead time for LM2904WYDT should be confirmed through the Request a Quote form on this page, including the required quantity and production date. Lead time can vary with the manufacturer’s inventory, incoming supply, and the exact orderable suffix. The 8-SOIC package and exact MPN should be stated clearly in the request to avoid confusion with other LM2904 variants.
Where can I buy LM2904WYDT online?
Use the Request a Quote form on this page to request LM2904WYDT from XAIPART and confirm current stock, lot traceability, and lead time. The request should identify the exact 8-SOIC MPN and required quantity. Because LM2904 orderable suffixes differ in grade and packaging, do not approve a quote that substitutes another suffix without checking its manufacturer datasheet.
What design limitations matter most for LM2904WYDT?
Input offset voltage, input bias current, common-mode range, output swing, and output-current capability are the principal limitations to verify. The LM2904WYDT has a 1.1 MHz gain-bandwidth product and a 3 V to 30 V supply range, so it is primarily suited to low-frequency general-purpose work. The STMicroelectronics manufacturer datasheet should guide gain selection, output loading, bypass-capacitor selection, and any need for isolation around high-impedance sources.

کے لیے انجینئرنگ ریفرنس ڈیٹا LM2904WYDT — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose LM2904WYDT when the design requires two independent, general-purpose amplifier channels, an 8-SOIC footprint, operation from a 3 V to 30 V supply, and approximately 1.1 MHz gain-bandwidth performance. LM2904YDT is appropriate when the non-reel orderable form matches the assembly plan, while LM2904WDT may suit a design requiring the standard-temperature grade. LM2904DT is the basic 8-SOIC family option and is useful when the exact suffix does not affect sourcing. Evaluate LM2904BDT or LM2904BYDT when the later B-family revision provides a preferred electrical or documentation profile. All listed candidates retain the same basic dual-amplifier footprint, but the engineer must still compare temperature limits, offset, bias current, slew rate, output swing, and availability. Use LM2904WYDT for new general-purpose industrial designs unless the system requires a precision, low-offset, rail-to-rail, or high-speed amplifier.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ LM2904YDT LM2904WDT LM2904DT LM2904BDT LM2904BYDT
Brand STMicroelectronics STMicroelectronics STMicroelectronics STMicroelectronics STMicroelectronics STMicroelectronics
Package 8-SOIC 8-SOIC - same 8-SOIC - same 8-SOIC - same 8-SOIC - same 8-SOIC - same
Amplifier Configuration Dual, 2 channels Dual, 2 channels Dual, 2 channels Dual, 2 channels Dual, 2 channels Dual, 2 channels
Supply Voltage Range 3 V to 30 V 3 V to 30 V 3 V to 30 V 3 V to 30 V 3 V to 30 V 3 V to 30 V
Gain-Bandwidth Product 1.1 MHz 1.1 MHz 1.1 MHz 1.1 MHz 1.1 MHz 1.1 MHz
Output Type Single-ended Single-ended Single-ended Single-ended Single-ended Single-ended
Power Classification Low power Low power Low power Low power Low power Low power
Orderable Grade or Revision LM2904WYDT LM2904 Y grade LM2904 W grade LM2904 standard orderable suffix LM2904 B revision LM2904 B revision with Y grade

اہم امتیازی خصوصیات

  • Two independent general-purpose channels in one compact package (بمقابلہLM2902MTX)
  • Wide supply range for industrial interface designs (بمقابلہLM2904WDT)
  • Defined single-ended output architecture (بمقابلہLM2904DT)
  • Common-mode rejection for differential signal conditioning (بمقابلہLM2904BDT)

ڈیزائن نوٹس

Confirm the actual positive and negative rail magnitudes against the 3 V to 30 V supply limit. In a split-supply circuit, the total rail-to-rail voltage must remain below 30 V even during transient excursions. Place the bypass capacitor close to the V+ pin and return its ground end directly to the V- reference plane. The two channels share the same supply pins, so their total supply-current demand must be included in the regulator and thermal budget.

Route each non-inverting input directly to its source and keep the inverting-input feedback loop short and compact. Sensitive input traces should remain away from switching-node copper, high-current motor paths, and inductors. Connect the two supply pins to a low-impedance plane and use a local bypass capacitor so transient current does not travel through long traces. Pin 1 should be identified correctly on the 8-SOIC footprint to avoid reversing the two amplifier channels.

Do not assume that the 3 V to 30 V supply rating permits operation with every input signal at those voltages. Check the input common-mode range and output swing in the STMicroelectronics manufacturer datasheet for the actual supply. Also verify the source impedance, because input bias current can create offset error in high-impedance circuits, and add isolation when driving capacitive loads if the selected revision requires it.

تعمیل کی معلومات

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

The exact LM2904WYDT compliance status requires confirmation from the current STMicroelectronics product declaration or manufacturer ordering documentation.

ڈیٹا کی تصدیق کی تاریخ: 2026-11-17 — ڈیٹا XAIPART کی کمپوننٹ انجینئرنگ ٹیم کے ذریعے تصدیق شدہ اور ترتیب شدہ

متعلقہ تلاشیں

lm2904wydt datasheet LM2904WYDT pinout LM2904WYDT datasheet pdf LM2904WYDT 8-SOIC LM2904WYDT 3V to 30V LM2904WYDT 1.1MHz STMicroelectronics LM2904WYDT LM2904WYDT equivalent LM2904WYDT replacement LM2904WYDT vs LM2904YDT LM2904WYDT sensor amplifier LM2904WYDT price

متعلقہ اجزاء اور اصطلاحات

STMicroelectronics LM2904WYDT LM2904YDT LM2904WDT LM2904DT LM2904BDT LM2904BYDT operational amplifier dual operational amplifier general-purpose amplifier low-power amplifier analog signal conditioning single-ended output gain-bandwidth product common-mode rejection 8-SOIC SOIC package family surface-mount package industrial sensor interface audio preamplifier motor control current-loop signal processing active filter battery-powered interface
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں