LM339APWRG4 - Quad Open-Collector Comparator | Texas Instruments
N.º da peça: LM339APWRG4 ✓ AtivoLM339APWRG4 Visão geral
A comparator is an analog integrated circuit that compares two input voltages and produces a digital-level indication of their relationship. The LM339 belongs to the comparator hierarchy, which sits alongside amplifiers, analog switches, and sensors as a core building block for signal conditioning. Its differential inputs detect threshold crossings, overvoltage events, zero-crossing points, and magnitude comparisons in control and monitoring circuits.
The LM339APWRG4 provides four comparison channels, a supply-voltage operating range extending to 36 V, a typical supply-current drain of 0.8 mA, and a low typical input bias current. Its open-collector outputs require an external pull-up resistor and permit the output stage to be pulled to the voltage required by the attached logic system. The wide operating range makes the device suitable for industrial control, power-supply monitoring, and interface conversion circuits.
The four channels share a common ground and supply connection but otherwise operate independently. Differential input voltage can be handled over a range equal to the maximum-rated supply voltage, while the common-mode input range includes ground. This architecture is useful when sensing small changes around a ground-referenced signal or when one input is tied to a precision threshold reference.
Typical applications include four-channel level detection, window comparison, battery and power-rail supervision, zero-crossing detection, sensor interfacing, and TTL-to-CMOS translation. In each case, the open-collector output can sink current from a pull-up network while leaving the logic voltage independent of the comparator supply.
When designing around the LM339APWRG4, place the pull-up resistor close to the driven logic input and route comparator inputs away from switching nodes and high-current traces. Because open-collector outputs cannot actively source current, account for the pull-up value when setting rise time. Confirm the input common-mode range and output timing against the system operating limits before releasing the layout.
This page combines manufacturer specifications, package and pin information, practical application guidance, and drop-in replacement analysis to support faster component selection and PCB-level implementation planning.
Alternativas drop-in para LM339APWRG4 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com LM339APWRG4 (mesmo formato e footprint) — diferindo em Package, Logic Compatibility, Differential Input Voltage Range, Input Bias Current, Comparator Type.
LM339PWRG4
✅ Drop-InConsulte o preço
Ver ficha técnica →LM339PWRE4
✅ Drop-InConsulte o preço
Ver ficha técnica →LM339PWRG3
✅ Drop-InConsulte o preço
Ver ficha técnica →LM339APWR
✅ Drop-InConsulte o preço
Ver ficha técnica →LM2901PW
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LM339APWRG4 Classificações máximas e características elétricas
| Comparator Type | Quad differential comparator |
| Number of Channels | 4 channels |
| Tipo de saída | Open collector |
| Supply Voltage Range | 2 V to 36 V |
| Maximum Supply Voltage | 36 V |
| Supply Current Drain | 0.8 mA typical |
| Input Bias Current | Low input bias current |
| Differential Input Voltage | Equal to maximum-rated supply voltage |
| Common-Mode Input Voltage | Includes ground |
| Logic Compatibility | Compatible with TTL, MOS, and CMOS |
| Encapsulamento | 14-pin TSSOP |
| Tipo de montagem | Surface mount |
| Operating Configuration | Single supply or split supply |
| Comparator Response Time | 300 ns |
| Output Pull-Up Requirement | External pull-up resistor required |
| RoHS Compliance | Compliant |
Configuração de pinos do LM339APWRG4
| Pino 1 | OUT 1 — Open-collector output of comparator 1 |
| Pino 2 | IN 1- — Inverting input of comparator 1 |
| Pino 3 | IN 1+ — Non-inverting input of comparator 1 |
| Pino 4 | GND — Common ground connection |
| Pino 5 | IN 2+ — Non-inverting input of comparator 2 |
| Pino 6 | IN 2- — Inverting input of comparator 2 |
| Pino 7 | OUT 2 — Open-collector output of comparator 2 |
| Pino 8 | OUT 3 — Open-collector output of comparator 3 |
| Pino 9 | IN 3+ — Non-inverting input of comparator 3 |
| Pino 10 | IN 3- — Inverting input of comparator 3 |
| Pino 11 | OUT 4 — Open-collector output of comparator 4 |
| Pino 12 | IN 4- — Inverting input of comparator 4 |
| Pino 13 | IN 4+ — Non-inverting input of comparator 4 |
| Pino 14 | VCC — Common positive supply connection |
Aplicações típicas
LM339APWRG4 é adequado para 6 aplicaçãos: Power-Rail Voltage Monitoring, Multi-Level Signal Detection, Battery Threshold Supervision, Zero-Crossing Detection, TTL and CMOS Logic Interface, Window and Over/Under Detection.
Power-Rail Voltage Monitoring
The LM339APWRG4 is appropriate for monitoring positive power rails against fixed or adjustable reference thresholds because its differential inputs operate with a common-mode range that includes ground. Each channel can supervise a separate rail, and the open-collector output can pull down a logic node through an external pull-up resistor. The 36 V maximum supply rating accommodates industrial systems while the 0.8 mA typical supply drain limits standing power. Add hysteresis around the switching point to prevent repeated alarm activity as the monitored rail moves near the threshold.
Recomendado
Multi-Level Signal Detection
Four independent comparator channels make the LM339APWRG4 useful for multi-level detection where analog signals must be converted into discrete logic states. Each channel can compare a sensor or divider output with its own threshold, while the shared package reduces the component count compared with separate single comparators. Because the outputs are open collector, pull-ups can be tied to the voltage required by a TTL, MOS, or CMOS receiver. Keep the input traces short and place the threshold resistors near the associated input pins.
Recomendado
Battery Threshold Supervision
The LM339APWRG4 can compare a divided battery voltage against precise thresholds for charge-state indication, low-battery alarms, or system cutoff control. The comparator's differential input arrangement supports ground-referenced sensing, while the wide supply range allows operation in systems above the voltage being monitored when adequate headroom exists. Use a stable reference for the threshold side of the comparison and add positive feedback for hysteresis. The open-collector output can directly pull down an enable, indicator, or isolation signal through a pull-up network.
Recomendado
Zero-Crossing Detection
The LM339APWRG4 can detect the point at which an input waveform crosses a reference by placing the waveform and threshold on the two differential inputs. This is useful for AC-coupled timing, phase, and event-detection circuits where the input crosses a nominal zero or mid-supply reference. The 300 ns response time supports relatively fast threshold events, and the common-mode range including ground is advantageous for bipolar signals referenced to ground. Use hysteresis and careful return-path routing to avoid false triggering around the crossing point.
Recomendado
TTL and CMOS Logic Interface
The open-collector output of the LM339APWRG4 allows a logic-family conversion when the pull-up resistor is connected to the receiving family's supply. This arrangement is useful when a low-voltage comparator section must drive TTL, MOS, or CMOS inputs with a different supply voltage. The output stage sinks the pull-up current when the comparison indicates the opposite state, while the resistor establishes the high level. Select the pull-up resistance to balance transition speed against power dissipation and confirm the output's allowable sink current in the manufacturer data sheet.
Recomendado
Window and Over/Under Detection
Two LM339APWRG4 channels can form a voltage window detector by comparing a monitored signal against upper and lower reference levels. Each open-collector output can pull a shared wired-AND node through its own pull-up, producing a fault signal when either limit is exceeded. This arrangement supports industrial limit detection, instrument protection, and automated test equipment. Reference resistors should have suitable tolerance and temperature stability, while the signal path should avoid proximity to switching converters to prevent false threshold crossings.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para LM339APWRG4 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | LM339PWRG4 | LM339PWRE4 | LM339PWRG3 | LM339APWR | LM2901PW |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP |
| Comparator Channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Supply Voltage Range | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V |
| Output Type | Open collector | Open collector | Open collector | Open collector | Open collector | Open collector |
| Response Time | 300 ns | 300 ns | 300 ns | 300 ns | 300 ns | 300 ns |
| Supply Configuration | Single supply or split supply | Single supply or split supply | Single supply or split supply | Single supply or split supply | Single supply or split supply | Single supply or split supply |
| Logic Compatibility | TTL, MOS, and CMOS compatible with external pull-up | TTL, MOS, and CMOS compatible with external pull-up | TTL, MOS, and CMOS compatible with external pull-up | TTL, MOS, and CMOS compatible with external pull-up | TTL, MOS, and CMOS compatible with external pull-up | TTL, MOS, and CMOS compatible with external pull-up |
| Silicon Die Relationship | LM339A family device | Same silicon die as related LM339P order codes | Same silicon die as related LM339P order codes | Same silicon die as related LM339P order codes | Same LM339A configuration | Related LM2901 comparator family |
| External Pull-Up Resistor | Required | Required | Required | Required | Required | Required |
Principais diferenciais
- Four independent differential channels in one 14-pin TSSOP package (vs LM2901PW)
- Ground-inclusive common-mode input range (vs LM339PWRG4)
- Logic-family flexibility from the open-collector stage (vs LM339APWR)
Notas de projeto
Do not treat the open-collector output as a push-pull logic output. Every output requires a pull-up resistor, and the logic-high voltage is determined by the pull-up connection rather than by the comparator supply. Size the resistor to satisfy the receiver's input current, the output's sink-current limit, and the required rise time. Avoid leaving an output without a pull-up, because the resulting floating node can produce unreliable transitions.
Place each pull-up resistor close to the corresponding comparator output or receiving logic input to minimize the loop area that carries switching current. Route the two inputs of a comparator as a compact differential pair where possible, and connect the ground reference directly to the device ground pin rather than routing return current through an input trace. Keep comparator inputs away from inductors, switching nodes, and high-current power paths.
Add hysteresis with positive feedback when a monitored signal can cross the threshold slowly or contain noise. The feedback resistor raises the effective switching threshold as the output changes state, separating the turn-on and turn-off points. Keep the hysteresis network values small enough not to load the input source, and verify that the resulting trip points account for input offset, reference tolerance, and temperature variation.
Informações de conformidade
RoHS compliance is documented for the LM339APWRG4. The component is a general-purpose industrial comparator, so AEC-Q100 automotive qualification does not apply. REACH, halogen-free, lead-free, and conflict-minerals status require confirmation for the exact order code.