LMR64010XMFX/NOPB-Q1 - 40V Boost Regulator 1.6MHz | TI
N.º da peça: LMR64010XMFX/NOPB-Q1 ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $2.75 | $2,75 |
| 10 | $2.48 | $24,80 |
| 100 | $2.05 | $205,00 |
| 500 | $1.78 | $890,00 |
| 1.000 | $1.52 | $1.520,00 |
LMR64010XMFX/NOPB-Q1 Visão geral
A boost converter is a type of switching regulator (DC-DC converter) in the broader power management IC family that steps an input voltage up to a higher regulated output by storing energy in an inductor during the switch on-time and releasing it to the output during the off-time. Boost converters complement LDO linear regulators, which can only step down; the LMR64010 fills the step-up role with far higher efficiency than charge pumps.
Key features include the 40V internal switch rating, enabling output rails of 16V or higher from low-voltage inputs; a 1.6 MHz fixed-frequency current-mode control topology that allows small inductors and ceramic capacitors, yielding high power density in the tiny SOT-23 footprint; and minimal internal switch power loss that eliminates the need for a heatsink. The adjustable feedback reference allows any output within range via an external resistor divider.
Technically, current-mode control provides fast transient response and straightforward loop compensation, while the 1.6 MHz switching frequency keeps ripple components above sensitive analog bands. Internal cycle-by-cycle current limiting and thermal shutdown protect the device during faults.
Typical applications include LCD/LED bias supplies for automotive displays, sensor and amplifier high-voltage rails, white LED backlight drivers, and general-purpose 5V-to-20V+ point loads where a discrete controller would be too complex. The low 2.7V startup floor suits single-cell Li-ion and 3.3V industrial buses.
Design tip: keep the switch node, inductor, and output diode loop as short as possible; verify output diode reverse-voltage rating exceeds 40V, and check thermal rise because SOT-23 dissipation is limited.
Alternativas drop-in para LMR64010XMFX/NOPB-Q1 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com LMR64010XMFX/NOPB-Q1 (mesmo formato e footprint) — diferindo em Output Voltage Range, Package, RoHS Status.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
LMR64010XMFX/NOPB
✅ Drop-In✓ Em estoque
$1.15 / unidade
Ver ficha técnica →LMR64010XMF/NOPB
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LM2733XMFX/NOPB
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LM2731XMFX/NOPB
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
MIC2288YML
⚡ Mesmo encapsulamento ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
LMR64010XMFX/NOPB-Q1 Classificações máximas e características elétricas
| Topologia | Boost (step-up), current-mode |
| Faixa de tensão de entrada | 2.7 V to 14 V |
| Faixa de tensão de saída | Adjustable, up to 40 V |
| Switch Current Limit | 1 A (internal switch) |
| Frequência de comutação | 1.6 MHz (fixed) |
| Control Method | Current-mode, fixed frequency |
| Encapsulamento | SOT-23-5 (SC-74A, SOT-753) |
| Tipo de montagem | Surface Mount |
| Automotive Qualification | AEC-Q100 (Q1 designation) |
| Protections | Current limit, thermal shutdown |
| Output Polarity | Positive |
| Número de saídas | 1 |
| Brand Family | SIMPLE SWITCHER |
| Status RoHS | Compliant (NOPB / no Pb termination) |
Configuração de pinos do LMR64010XMFX/NOPB-Q1
| Pino 1 | SW — Switch node - connect inductor and catch diode |
| Pino 2 | GND — Ground |
| Pino 3 | FB — Feedback input from output resistor divider |
| Pino 4 | VIN — Input supply, 2.7V to 14V |
| Pino 5 | NC — No connection (per datasheet connection diagram - verify before layout) |
Aplicações típicas
LMR64010XMFX/NOPB-Q1 é adequado para 6 aplicaçãos: Automotive LCD Display Bias, White LED Backlight Driver, Op-Amp and Sensor High-Voltage Rails, Battery-Powered Portable Devices, Industrial PLC and Sensor Hubs, Automotive ADAS Module Auxiliary Rails.
Automotive LCD Display Bias
The LMR64010XMFX/NOPB-Q1 boosts a 5V or 12V automotive rail to the 16V-40V levels needed for LCD display bias and VCOM drivers, and its AEC-Q100 (-Q1) qualification directly addresses automotive reliability requirements. The 1.6 MHz fixed switching keeps ripple components away from the display driver bandwidth, and the internal 1A switch eliminates external FETs, shrinking the solution to a SOT-23 footprint with a small 10uH-class inductor.
Recomendado
White LED Backlight Driver
For LED backlight strings requiring 20V-40V drive headroom from a 5V input, the LMR64010's 40V switch rating and adjustable feedback enable constant-voltage bias with current-setting resistors or an external current sense. The 1.6 MHz frequency permits small 2mm-class inductors and ceramic output capacitors, key for thin automotive and industrial display modules, while cycle-by-cycle current limit protects against shorted LED strings.
Recomendado
Op-Amp and Sensor High-Voltage Rails
Precision analog front ends often need 15V-30V rails from a single 5V supply. The LMR64010 generates these rails with a current-mode loop that responds quickly to load transients from switched sensor channels. Following it with a low-noise LDO removes switching ripple for the analog rail, combining boost efficiency with LDO noise performance - a common two-stage architecture in test and measurement and medical sensing boards.
Recomendado
Battery-Powered Portable Devices
With a 2.7V minimum input, the LMR64010 operates directly from single-cell Li-ion and even two-cell alkaline packs, boosting to the 12V-30V levels needed by pyroelectric IR sensors, vacuum fluorescent displays, or piezo actuators. The internal 1A switch and SOT-23 package keep height and area minimal for handheld enclosures, and thermal shutdown protects against blocked-vent faults in compact products.
Recomendado
Industrial PLC and Sensor Hubs
Industrial 24V-system boards commonly derive a lower internal rail and then boost locally for analog outputs, HART modems, or sensor excitation needing 20V-36V. The 14V input ceiling supports post-buck 12V buses, and the fixed 1.6 MHz clock avoids interference with 4-20 mA and low-frequency industrial signaling. The standard LMR64010XMFX/NOPB suits industrial-grade deployments, with -Q1 for extended-reliability segments.
Recomendado
Automotive ADAS Module Auxiliary Rails
Camera and radar modules in ADAS platforms need auxiliary 20V-40V rails for bias networks, heater elements, or photodiode reverse bias. The -Q1 qualified LMR64010 provides these from a 5V or 8V module rail within an AEC-Q100 bill of materials. Its 1.6 MHz operation stays clear of radar IF bands, and the tiny SOT-23 solution fits dense module PCBs where inductor size dominates board area.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para LMR64010XMFX/NOPB-Q1 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | LMR64010XMFX/NOPB | LMR64010XMF/NOPB | LM2733XMFX/NOPB | LM2731XMFX/NOPB |
|---|---|---|---|---|---|
| Package | SOT-23-5 (SC-74A) | SOT-23-5 - same | SOT-23-5 - same | SOT-23-5 - same | SOT-23-5 - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Input Voltage Range | 2.7V to 14V | 2.7V to 14V | 2.7V to 14V | 2.7V to 14V | 2.7V to 14V |
| Switch Current | 1A | 1A | 1A | 1A | 1A / 0.5A variants |
| Switching Frequency | 1.6 MHz | 1.6 MHz | 1.6 MHz | 1.6 MHz / 600 kHz variants | 1.6 MHz / 600 kHz variants |
| Status | Active | Active | Active | Legacy (still stocked) | Active |
Principais diferenciais
- AEC-Q100 automotive qualification (vs LMR64010XMFX/NOPB)
- 40V internal switch in SOT-23 (vs LM2731XMFX/NOPB)
- Newer SIMPLE SWITCHER platform vs legacy (vs LM2733XMFX/NOPB)
Notas de projeto
Keep the SW-GND-diode loop as short as possible: place the inductor, catch diode, and input capacitor within 2-3 mm of the SOT-23 pins. The 1.6 MHz switching edges generate high di/dt; a compact loop minimizes radiated EMI and ring on the switch node. Use a solid ground plane under the part and a 10uF ceramic input capacitor with X7R dielectric to prevent input dips during switch on-time.
Select a catch diode rated at least 40V reverse and rated for the full average output current - a Schottky such as a 40V/1A type minimizes loss. Budget inductor saturation current above the 1A switch current limit. Remember that in a boost converter, average input current exceeds output current; at 5V-to-24V conversion, 100 mA output draws roughly 500 mA from the input.
The SOT-23 package has limited dissipation; losses come from switch conduction, diode, and inductor DCR. At high boost ratios or outputs above ~100 mA, estimate efficiency from the datasheet curves and verify junction temperature stays within the -Q1 grade limit. Adding 2 oz copper and thermal vias under GND reduces theta_JA meaningfully in this footprint.
Informações de conformidade
NOPB suffix indicates no-Pb (lead-free) termination. AEC-Q100 qualification inferred from -Q1 suffix; verify on TI.com product page. REACH and halogen-free status not present in provided data.
