LT3045HMSE#Z-EP - 500mA 20V Ultra-Low Noise LDO | ADI
N.º da peça: LT3045HMSE#Z-EP ✓ AtivoLT3045HMSE#Z-EP Visão geral
An LDO (Low-Dropout) linear regulator is a type of voltage regulator that maintains a stable output voltage even when the input voltage is very close to the output voltage. Within the broader system hierarchy, the LT3045HMSE#Z-EP sits as LDO -> linear regulator -> voltage regulator -> power management IC -> semiconductor. Unlike switching regulators, LDOs trade efficiency for the absence of switching ripple, making them the preferred post-regulator for noise-sensitive analog blocks.
Key features include 0.8 uVrms output noise (10 Hz to 100 kHz), 75 dB PSRR at 1 MHz, and 2.2 mA quiescent current. The part also integrates reverse-battery protection, reverse-current protection, internal current limit with foldback, and thermal limit with hysteresis. The exposed pad MSOP-12 keeps theta_JA low for reliable operation at elevated ambient temperatures in ruggedized environments.
Architecturally, the LT3045 uses a precision current-source reference followed by a high-gain unity-gain output stage, producing noise performance that is essentially independent of output voltage and load current. Its wideband PSRR allows the part to clean up switching-converter residuals in multi-rail systems, eliminating the need for additional LC filters.
Typical applications include RF and microwave power rails, military/aerospace avionics, precision data-converter power supplies, and post-regulation for switching converters. The 0 V minimum output enables biasing of negative-rail op-amps or biased negative references when combined with an external charge pump.
When designing with the LT3045HMSE#Z-EP, ensure the exposed pad is soldered to at least 1 sq-in of copper to keep junction temperature in range, and place the 10 uF minimum ceramic output capacitor directly at the OUT pins. The -EP suffix designates Enhanced Product flow for AQEC and defense applications; for industrial/consumer designs, use the standard LT3045HMSE#PBF part number.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
Alternativas drop-in para LT3045HMSE#Z-EP — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com LT3045HMSE#Z-EP (mesmo formato e footprint) — diferindo em Dropout Voltage, Operating Temperature, PSRR, Package, Quiescent Current.
LT3045HMSE#PBF
✅ Drop-InConsulte o preço
Ver ficha técnica →LT3045IMSE#PBF
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LT3045EMSE#TRPBF
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LT3045EDD#PBF
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LT3042EDD#PBF
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LT3045HMSE#Z-EP Classificações máximas e características elétricas
| Manufacturer | Analog Devices |
| MPN | LT3045HMSE#Z-EP |
| Series | LT3045-EP (Enhanced Product / AQEC) |
| Product Type | LDO Linear Voltage Regulator |
| Tipo de saída | Adjustable (positive) |
| Número de saídas | 1 |
| Faixa de tensão de saída | 0 V to 15 V |
| Corrente máxima de saída | 500 mA |
| Faixa de tensão de entrada | 1.8 V to 20 V |
| Tensão de dropout | 260 mV (typ at 500 mA) |
| Ruído de saída | 0.8 uVrms (10 Hz to 100 kHz) |
| PSRR | 75 dB at 1 MHz |
| Corrente de repouso | 2.2 mA (typ) |
| Minimum Output Capacitor | 10 uF ceramic |
| Encapsulamento | 12-lead MSOP-EP (MSE), thermally enhanced |
| Tipo de montagem | Surface Mount |
| Temperatura de operação | -40 C to +150 C (junction) |
| Protection Features | Reverse-battery, reverse-current, internal current limit with foldback, thermal limit with hysteresis |
| Qualification | Enhanced Product (EP), AQEC, defense/aerospace |
Configuração de pinos do LT3045HMSE#Z-EP
| Pino 1 | OUT — Regulated output voltage |
| Pino 2 | OUT — Regulated output voltage |
| Pino 3 | SET — Output voltage programming (resistor divider to ground) |
| Pino 4 | IN — Input supply voltage |
| Pino 5 | IN — Input supply voltage |
| Pino 6 | EN/UVLO — Enable / undervoltage lockout input |
| Pino 7 | NC — Not connected (per datasheet) |
| Pino 8 | PG — Power good indicator output |
| Pino 9 | GND — Ground reference |
| Pino 10 | GND — Ground reference |
| Pino 11 | ILIM — Current limit programming (resistor to ground) |
| Pino 12 | SENSE — Output voltage sense for regulation feedback |
Aplicações típicas
LT3045HMSE#Z-EP é adequado para 6 aplicaçãos: RF and Microwave Power Rails, Defense and Aerospace Avionics, Precision Data-Converter Power, Switching-Converter Post-Filter, Test and Measurement Instrumentation, Industrial Process Control.
RF and Microwave Power Rails
The LT3045HMSE#Z-EP's 0.8 uVrms output noise and 75 dB PSRR at 1 MHz make it an excellent choice for powering RF VCOs, PLLs, mixers, and LNAs. The 500 mA output current supports multi-stage receiver chains while the ultra-low noise prevents reciprocal mixing and phase-noise degradation in narrowband radios. Place the LDO downstream of a switching pre-regulator; the part's wideband PSRR cleans residuals that would otherwise appear on the LO. The MSOP-12-EP package keeps the part compact for dense RF front-end boards used in defense transceivers.
Recomendado
Defense and Aerospace Avionics
The LT3045HMSE#Z-EP's Enhanced Product (EP) flow and AQEC qualification make it suitable for defense and aerospace avionics power systems. The 20 V maximum input withstands 28 V transient spikes common in military vehicle buses, while the 0 V to 15 V adjustable output supports legacy +12 V and +15 V avionics rails. The MSOP-12-EP package's exposed pad provides thermal headroom at high altitude where convective cooling is reduced, and the EP reliability flow provides traceability and documentation for mission-critical programs.
Recomendado
Precision Data-Converter Power
High-resolution ADCs and DACs require power rails that do not inject noise into the analog signal path. The LT3045HMSE#Z-EP delivers 0.8 uVrms output noise from 10 Hz to 100 kHz, which is below the quantization noise floor of many 16-bit and 18-bit converters. The 75 dB PSRR at 1 MHz rejects residual ripple from upstream switching converters when the design uses a multi-stage power architecture. The 0 V minimum output enables precise reference-ground biasing for instrumentation-grade measurement systems used in defense applications.
Recomendado
Switching-Converter Post-Filter
Place the LT3045HMSE#Z-EP downstream of a switching buck or boost converter to produce a clean, low-noise output rail. The part's 75 dB PSRR at 1 MHz suppresses switching ripple that would otherwise reach sensitive analog blocks, eliminating the need for additional LC filter stages. The 500 mA current capability handles moderate-load analog subsystems, while the 260 mV typical dropout allows tight headroom budgeting in compact designs. This architecture is widely used in portable test equipment and field-deployed instruments.
Recomendado
Test and Measurement Instrumentation
Bench-top and field-portable test instruments demand clean, stable supply rails that do not contaminate measurements of small analog signals. The LT3045HMSE#Z-EP delivers 0.8 uVrms output noise and 75 dB PSRR at 1 MHz, ensuring that supply noise does not couple into high-impedance signal paths. The adjustable output from 0 V to 15 V supports the wide range of analog rails common in mixed-signal test platforms. The MSOP-12-EP package allows dense placement near the analog front-end for minimal PCB-area-tracking noise pickup.
Recomendado
Industrial Process Control
Industrial process control systems operate in electrically noisy environments where supply regulation must reject motor-drive transients and switching noise. The LT3045HMSE#Z-EP provides 75 dB PSRR at 1 MHz and full reverse-battery and reverse-current protection, suiting it to 24 V industrial bus rails. The 0 V minimum output supports legacy 0.16 V loop powered instrumentation when used with an external boost or charge pump. The exposed-pad MSOP-12 package handles continuous power dissipation in factory-floor equipment with elevated ambient temperatures.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para LT3045HMSE#Z-EP — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | LT3045HMSE#PBF | LT3045IMSE#PBF | LT3045EMSE#TRPBF |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 12-MSOP-EP (MSE) | 12-MSOP-EP (MSE) - same | 12-MSOP-EP (MSE) - same | 12-MSOP-EP (MSE) - same |
| Output Current | 500 mA | 500 mA | 500 mA | 500 mA |
| Output Voltage Range | 0 V to 15 V | 0 V to 15 V | 0 V to 15 V | 0 V to 15 V |
| Output Noise | 0.8 uVrms | 0.8 uVrms | 0.8 uVrms | 0.8 uVrms |
| PSRR at 1 MHz | 75 dB | 75 dB | 75 dB | 75 dB |
| Qualification | EP / AQEC (defense/aerospace) | Standard commercial | Industrial grade | E-grade commercial |
| Temperature Grade | EP / defense (-40C to +150C junction) | Standard commercial | Industrial (-40C to +125C) | Extended commercial |
Principais diferenciais
- Enhanced Product (EP) / AQEC qualification for defense and aerospace (vs LT3045HMSE#PBF)
- 0 V minimum output voltage capability (vs LT3045IMSE#PBF)
- Industry-leading wideband PSRR at 1 MHz (vs LT3045EMSE#TRPBF)
Notas de projeto
The MSOP-12-EP package relies on its exposed thermal pad for heat removal. Solder the pad to a copper pour of at least 1 square inch on the top layer, supplemented with thermal vias to inner-layer ground planes. Estimated: at VIN=12 V, VOUT=5 V, and 500 mA load, power dissipation is approximately 3.5 W; without adequate copper the junction temperature will exceed 150 C and trigger thermal shutdown. Keep high-current traces wide to reduce copper losses.
Place the 10 uF minimum ceramic output capacitor as close as possible to the OUT and GND pins. Use X7R or X5R dielectric; the ESR must remain below 50 milliohm across the operating temperature range. Place input capacitors symmetrically to the IN pins to minimize parasitic inductance. The exposed pad connection should use an array of 0.3 mm thermal vias in a 3x3 grid for best heat spreading.
Do not exceed the absolute maximum input voltage of 20 V. The reverse-battery protection circuit can only withstand limited reverse voltage; add an external TVS for full protection in 24 V industrial bus applications. Ensure the SET pin resistor divider uses 1% tolerance or better to maintain output accuracy. The PG (power good) pin is open-drain; do not float it without a pull-up resistor if monitoring is desired.
Informações de conformidade
Compliance details not present in Verified Web Data; refer to manufacturer datasheet RoHS/REACH declaration for definitive values. -EP suffix indicates Enhanced Product / AQEC flow for defense and aerospace applications per Analog Devices Enhanced Product documentation.
