MAX232CEAWE+T - 2/2 RS-232 Transceiver | Analog Devices
N.º da peça: MAX232CEAWE+T ✓ AtivoMAX232CEAWE+T Visão geral
An RS-232 transceiver is an interface IC that combines drivers and receivers for serial data communication. The driver converts a logic-level input into the bipolar voltage signaling used by RS-232, while the receiver converts a bipolar RS-232 input into a logic-level output. As a full-duplex 2/2 device, the MAX232CEAWE+T supports two transmit channels and two receive channels in one package.
Its principal features include two RS-232 drivers, two RS-232 receivers, operation from a +5 V supply, and operation from -40°C to +125°C. The extended temperature range makes the device suitable for industrial equipment, control systems, instrumentation, and communications equipment that must operate across a broad environmental range. The 16-SOIC package supports conventional surface-mount PCB assembly.
The MAX232 family combines a dual RS-232 driver and dual receiver with charge-pump voltage generation, allowing the interface to produce RS-232 levels from a single positive supply. Because this is an integrated transceiver, a system can use fewer discrete interface components than a design composed of separate drivers, receivers, and level-shifting circuits. Charge-pump capacitors and supply-decoupling components remain external to the IC.
Typical uses include serial service ports, industrial controllers, data-acquisition equipment, test and measurement instruments, and embedded systems that communicate with RS-232 equipment. The two-driver and two-receiver arrangement is useful for point-to-point links where both ends can transmit and receive. A transceiver does not define the serial baud rate or protocol framing; those functions are handled by the host UART and application firmware.
For PCB implementation, place the required charge-pump and bypass capacitors close to their associated pins, route the RS-232 driver outputs as impedance-controlled interfaces, and keep switching or high-current paths away from receiver inputs. Confirm the logic levels of the attached UART before connecting the transceiver because RS-232 voltage levels are not directly compatible with TTL or CMOS logic.
This product guide combines the exact MAX232CEAWE+T device information with application guidance, engineering considerations, and clearly qualified drop-in comparison options. It also organizes sourcing, datasheet, replacement, and pinout questions so engineers can evaluate the interface quickly without overlooking temperature-range, package, or supply requirements.
Alternativas drop-in para MAX232CEAWE+T — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com MAX232CEAWE+T (mesmo formato e footprint) — diferindo em Package, Supply Voltage, AEC-Q100 Qualification, Data Rate, Function.
MAX232ESE+T
✅ Drop-InConsulte o preço
Ver ficha técnica →MAX232CSE+T
✅ Drop-In ⚠️ Especificações não verificadasConsulte o preço
Ver ficha técnica →MAX232ASE+T
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
MAX232AESE+T
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
MAX232ACSE+T
✅ Drop-In ⚠️ Especificações não verificadasConsulte o preço
Ver ficha técnica →MAX232CEAWE+T Especificações
| Product Type | 2/2 full RS-232 transceiver |
| Transmitter Configuration | 2 transmitters |
| Receiver Configuration | 2 receivers |
| Interface Standard | RS-232 |
| Tensão de alimentação | +5 V |
| Faixa de temperatura de operação | -40°C to +125°C |
| Encapsulamento | 16-SOIC |
| Contagem de pinos | 16 pins |
| Tipo de montagem | Surface mount |
| Channel Direction | Full duplex |
| Driver and Receiver Count | 2 drivers and 2 receivers |
| Status RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
Guia de Configuração de Pinos do MAX232CEAWE+T 16-soic
Configuração de pinos para MAX232CEAWE+T (pacote 16-soic). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para MAX232CEAWE+T.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
MAX232CEAWE+T é adequado para 6 aplicaçãos: Industrial Serial Control Interfaces, Data Acquisition Equipment, Test and Measurement Instruments, Serial Service and Configuration Ports, Networking and Communications Equipment, Embedded System Debug Interfaces.
Industrial Serial Control Interfaces
The MAX232CEAWE+T fits industrial controllers that require a compact, temperature-tolerant RS-232 interface. Its two drivers and two receivers support bidirectional point-to-point communication, while the -40°C to +125°C operating range suits equipment deployed across factory, process, and environmental-control environments. The +5 V supply and 16-SOIC package simplify integration into surface-mount control hardware. Connect the transceiver between the host UART and an external RS-232 connector, and place the manufacturer's recommended charge-pump and bypass capacitors close to their pins. Validate the UART logic levels, data rate, grounding, and protection requirements before releasing the PCB.
Recomendado
Data Acquisition Equipment
The MAX232CEAWE+T can provide a standard serial control channel between a data-acquisition instrument and a host computer. The integrated 2/2 arrangement allows the instrument to transmit commands and status while receiving configuration data over one RS-232 link. Its broad -40°C to +125°C range supports laboratory and industrial instrumentation, and the 16-SOIC package leaves more board area than larger discrete driver-receiver implementations. Use the manufacturer reference circuit for charge-pump capacitance and supply bypassing, and add the connector-level transient protection required by the installation environment.
Recomendado
Test and Measurement Instruments
For test and measurement instruments, the MAX232CEAWE+T offers a compact way to add a full-duplex RS-232 management port. Two transmitter channels can carry commands, calibration data, and results, while two receiver channels support host configuration and remote control traffic. The -40°C to +125°C range covers demanding industrial test environments, while +5 V operation simplifies power architecture. Keep sensitive analog and measurement sections separated from the RS-232 driver return currents, and verify whether the end product requires galvanic isolation, shield termination, or additional surge protection.
Recomendado
Serial Service and Configuration Ports
The MAX232CEAWE+T is well suited to service, configuration, and diagnostic ports on embedded and industrial equipment. A host can transmit setup commands and receive status messages through the two bidirectional channels, while the 16-SOIC package supports automated PCB assembly. Its extended -40°C to +125°C range allows use in equipment exposed to varied ambient conditions. The design must include the manufacturer-specified charge-pump capacitors and local supply decoupling, and the cable connector should receive ESD or surge protection appropriate to the exposed environment.
Recomendado
Networking and Communications Equipment
The MAX232CEAWE+T can be used for legacy RS-232 service channels in communications equipment where a full-duplex control link is required. Its two drivers and two receivers provide multiple serial paths without using separate driver and receiver packages, and its +5 V operation is compatible with conventional embedded logic. The -40°C to +125°C range supports industrial networking equipment. Preserve the separation between the RS-232 domain and other communications domains, observe recommended capacitor placement, and apply connector-level protection because the external cable can introduce transient voltage beyond the transceiver's operating limits.
Recomendado
Embedded System Debug Interfaces
The MAX232CEAWE+T can serve as a legacy debug or service interface on embedded control boards. Its full-duplex 2/2 arrangement allows a debugger to download commands and receive diagnostic responses through a standardized RS-232 connection. The 16-SOIC footprint is easy to route in a compact design, and operation over -40°C to +125°C supports industrial embedded products. Route driver outputs away from sensitive receiver traces, use a solid ground reference, and confirm the host UART's logic levels. External protection is particularly important when the RS-232 connector is connected to long or unprotected field cables.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para MAX232CEAWE+T — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | MAX232ESE+T | MAX232CSE+T | MAX232ASE+T | MAX232AESE+T | MAX232ACSE+T |
|---|---|---|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Transceiver Configuration | 2/2 full RS-232 transceiver | 2/2 full RS-232 transceiver | 2/2 full RS-232 transceiver | 2/2 full RS-232 transceiver | 2/2 full RS-232 transceiver | 2/2 full RS-232 transceiver |
| Driver Count | 2 | 2 | 2 | 2 | 2 | 2 |
| Receiver Count | 2 | 2 | 2 | 2 | 2 | 2 |
| Supply Voltage | +5 V | +5 V | +5 V | +5 V | +5 V | +5 V |
| Surface-Mount Footprint | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC |
| Special Features | Integrated dual driver and dual receiver | Integrated dual driver and dual receiver | Integrated dual driver and dual receiver | Integrated dual driver and dual receiver | Integrated dual driver and dual receiver | Integrated dual driver and dual receiver |
Principais diferenciais
- Exact +T ordering code with extended-temperature operation (vs MAX232ESE+T)
- Two transmitters and two receivers in one 16-SOIC package (vs MAX232CSE+T)
- Single-package integration reduces separate driver and receiver count (vs MC1489NE4)
Notas de projeto
Place the charge-pump capacitors and local supply-decoupling capacitor close to their associated MAX232 pins using the manufacturer layout and capacitance recommendations. Keep the driver output paths away from receiver inputs and sensitive analog circuitry. Route the two RS-232 channels as impedance-controlled interfaces, use a continuous ground reference, and place any connector protection close to the connector entry point.
Do not assume that the UART logic pins can directly connect to an external RS-232 connector; the MAX232 performs the required level translation. Verify input thresholds, output levels, polarity, timing, and data rate against the attached UART. Also confirm that the ordering suffix supplies the required temperature grade and that every PCB connection follows the exact pin-description diagram for the selected MPN.
Treat each RS-232 channel as a balanced, bipolar interface rather than a low-voltage single-ended signal. Terminate the cable and shield according to the connector and system grounding strategy, avoid long unprotected board traces, and use ESD or surge protection at exposed connectors. Keep ground current from external cables out of sensitive measurement paths to prevent common-mode disturbance.
The MAX232CEAWE+T is specified for -40°C to +125°C, but board temperature, copper area, airflow, and nearby heat sources must be checked against the manufacturer's maximum operating and package-temperature limits. Use the exact electrical characteristics for the selected suffix rather than assuming that every grade has identical limits across temperature.
Informações de conformidade
Compliance declarations were not identified in the exact-part records and must be confirmed using the manufacturer's current declaration or product documentation.