MAX3221EETE+T - 250kbps AutoShutdown RS-232 | Analog Devices
N.º da peça: MAX3221EETE+T ✓ AtivoMAX3221EETE+T Visão geral
An RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and the bipolar, inverted signaling used by RS-232 equipment. It belongs to the interface IC hierarchy, where it bridges UART, UART-compatible controller, and peripheral circuitry with legacy or industrial communications ports. The MAX3221E supports the EIA/TIA-232 and V.28/V.24 signaling requirements identified for the MAX3221E family.
The MAX3221EETE+T combines a 250 kbps data rate with a 3.0V to 5.5V supply range, allowing operation alongside both 3.3V and 5V digital systems. Its AutoShutdown circuit recognizes when connected equipment is powered off or no valid signal appears on a receiver input, then disables the internal charge pump and drivers to reduce power consumption. Automatic wakeup restores operation when a valid signal returns.
The enhanced electrostatic-discharge design protects the transmitter outputs and receiver inputs against ±15 kV ESD events. This protection is particularly useful for cables connected to external equipment, where electrostatic discharge can enter through a connector rather than through the protected logic-side pins. The device converts one TTL or CMOS data channel into an RS-232 signal and converts one inbound RS-232 signal back into a logic-level output.
Typical uses include industrial serial adapters, test and measurement equipment, point-of-sale terminals, security systems, and embedded systems that retain an RS-232 port. The 250 kbps capability supports substantially faster communication than conventional low-speed RS-232 links, while the small TQFN package suits compact control boards. Systems requiring more than one RS-232 port normally require additional transceiver channels or a multichannel interface family.
When laying out the PCB, place the charge-pump capacitors and interface capacitors close to their designated pins, connect the exposed thermal pad to the ground plane, and keep the RS-232 traces away from sensitive clock, sensor, and analog signals. Confirm capacitor values, voltage ratings, and exposed-pad soldering requirements against the manufacturer datasheet before fabrication.
This product page combines the manufacturer interface specifications with package, sourcing, application, and replacement guidance. It also highlights practical ESD, layout, power-management, and signal-integrity considerations that engineers can apply when integrating the MAX3221EETE+T into a compact RS-232 circuit.
Alternativas drop-in para MAX3221EETE+T — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com MAX3221EETE+T (mesmo formato e footprint) — diferindo em Package, ESD Protection, Maximum Data Rate, Supply Voltage Range, AutoShutdown Supply Current.
MAX3221ECTE+T
✅ Drop-In ⚠️ Especificações não verificadasConsulte o preço
Ver ficha técnica →MAX3221ECAE+T
✅ Drop-In ⚠️ Especificações não verificadasConsulte o preço
Ver ficha técnica →MAX3221EEAE-T
✅ Drop-In ⚠️ Especificações não verificadasConsulte o preço
Ver ficha técnica →MAX3221EETE+T Especificações
| Product Type | RS-232 transceiver |
| Transceiver Configuration | 1 transmitter and 1 receiver |
| Duplex Mode | Full duplex |
| Supply Voltage Range | 3.0 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| ESD Protection | ±15 kV |
| Shutdown Supply Current | 1 µA |
| Power Management Feature | AutoShutdown with automatic wakeup |
| Communication Standard | EIA/TIA-232 and V.28/V.24 |
| Logic Interface | TTL/CMOS-compatible |
| Encapsulamento | 16-pin TQFN with exposed pad |
| Package Dimensions | 5 mm × 5 mm |
| Tipo de montagem | Surface mount |
| Número de pinos | 16 pins |
| Status RoHS | RoHS details shown in comparison listings |
Guia de Configuração de Pinos do MAX3221EETE+T 5 mm × 5 mm
Configuração de pinos para MAX3221EETE+T (pacote 5 mm × 5 mm). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para MAX3221EETE+T.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
MAX3221EETE+T é adequado para 6 aplicaçãos: Industrial Serial Adapters, Test and Measurement Equipment, Point-of-Sale Terminals, Security and Access Systems, Embedded Control Systems, RS-232-to-Logic Conversion.
Industrial Serial Adapters
The MAX3221EETE+T suits compact adapters that must bridge a 3.3V or 5V controller with an external RS-232 port. Its 250 kbps data-rate capability provides useful throughput for configuration transfer and diagnostic protocols, while ±15 kV interface protection improves resilience at the cable-facing pins. AutoShutdown reduces consumption to 1 µA when the connected equipment is inactive. The circuit should use the manufacturer-recommended charge-pump and interface capacitors, with the exposed pad connected to ground according to the TQFN land pattern.
Recomendado
Test and Measurement Equipment
The MAX3221EETE+T provides a compact logic-to-RS-232 path for programmable instruments, laboratory controllers, and service interfaces. At up to 250 kbps, it supports faster command exchange than basic serial links, while its 3.0V to 5.5V range permits operation from common instrumentation supply rails. The ±15 kV ESD rating is useful when users attach external cables. Keep the interface route away from precision analog sections and use the datasheet ground and charge-pump capacitor arrangement to minimize coupling.
Recomendado
Point-of-Sale Terminals
MAX3221EETE+T is suitable for point-of-sale equipment that communicates with a receipt printer, scanner, or service terminal over RS-232. The single full-duplex channel can carry commands and responses, and the 250 kbps rating handles common retail protocols efficiently. Automatic shutdown lowers power use when the peripheral is disconnected or inactive, while ESD protection adds protection at the external connector. Confirm connector pin assignment and cable signaling before placing the transceiver in the PCB layout.
Recomendado
Security and Access Systems
The MAX3221EETE+T can connect a security controller or access-control terminal to a legacy alarm panel, intercom, or configuration computer through RS-232. Its ±15 kV ESD protection is valuable when the interface reaches an external connector, and AutoShutdown supports low-power operation during idle periods. The 250 kbps rate is more than adequate for typical command and event traffic. Use the complete manufacturer pin table and exposed-pad layout, and keep unprotected logic-side routing away from the cable entry.
Recomendado
Embedded Control Systems
The MAX3221EETE+T provides a straightforward way for a 3.3V embedded controller to communicate with an RS-232 service port. Its 250 kbps capability supports firmware download and diagnostic traffic, and the automatic shutdown and wakeup behavior can reduce system load when no peripheral is connected. The 5 mm by 5 mm TQFN package preserves board area, although the exposed pad requires proper thermal-pad layout and soldering. Validate logic levels, UART baud tolerance, and isolation requirements during component selection.
Recomendado
RS-232-to-Logic Conversion
MAX3221EETE+T is appropriate for standalone level-conversion circuits that interface legacy RS-232 equipment with modern CMOS logic. One receiver translates the incoming bipolar signal, and one transmitter produces the corresponding outgoing RS-232 signal. Its 3.0V to 5.5V operating range supports common supply choices, while ±15 kV protection strengthens the cable-facing interface. Follow the manufacturer’s external-capacitor and charge-pump layout because incorrect values or long capacitor routes can impair startup and signal integrity.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para MAX3221EETE+T — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | MAX3221ECTE+T | MAX3221ECAE+T | MAX3221EEAE-T |
|---|---|---|---|---|
| Package | TQFN-16 with exposed pad | TQFN-16 with exposed pad | TQFN-16 with exposed pad | TQFN-16 with exposed pad |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Transceiver Configuration | 1 transmitter and 1 receiver | 1 transmitter and 1 receiver | 1 transmitter and 1 receiver | 1 transmitter and 1 receiver |
| Supply Voltage Range | 3.0 V to 5.5 V | 3.0 V to 5.5 V | 3.0 V to 5.5 V | 3.0 V to 5.5 V |
| Maximum Data Rate | 250 kbps | 250 kbps | 250 kbps | 250 kbps |
| ESD Protection | ±15 kV | ±15 kV | ±15 kV | ±15 kV |
| Shutdown Supply Current | 1 µA | 1 µA | 1 µA | 1 µA |
| Power Management | AutoShutdown with automatic wakeup | AutoShutdown with automatic wakeup | AutoShutdown with automatic wakeup | AutoShutdown with automatic wakeup |
| Communication Standard | EIA/TIA-232 and V.28/V.24 | EIA/TIA-232 and V.28/V.24 | EIA/TIA-232 and V.28/V.24 | EIA/TIA-232 and V.28/V.24 |
Principais diferenciais
- Maintains the MAX3221E 16-pin TQFN drop-in platform (vs MAX3221ECTE+T)
- Combines 250 kbps operation with automatic power management (vs MAX3221ECAE+T)
- Provides enhanced cable-side ESD protection (vs MAX3221EEAE-T)
Notas de projeto
Place every charge-pump and interface capacitor directly between its designated pins and ground, using the shortest possible traces. The MAX3221E family uses internal switched-capacitor circuitry, so long capacitor connections can increase ringing, startup delay, and radiated noise. Follow the manufacturer PCB-layout example and keep the RS-232 traces short, away from clocks and analog inputs, and terminated according to the connected cable configuration.
Do not assume that any family member with a similar ordering code is automatically interchangeable. Confirm the 16-pin TQFN land pattern, exposed-pad connection, temperature grade, and tape-or-tube ordering requirement. The MAX3221ECTE+T, MAX3221ECAE+T, and MAX3221EEAE-T alternatives retain the same general interface ratings but their suffix differences may change environmental or packing requirements.
Keep the cable-facing RS-232 nets away from sensitive logic and analog traces, and provide a continuous ground reference beneath the interface area. Although the device includes ±15 kV ESD protection, protection is most effective when short connector-to-transceiver routes minimize surge current paths. If a cable crosses a board boundary, add the connector-side protection and grounding arrangement required by the system’s ESD and EMC architecture.
Use the MAX3221EETE+T AutoShutdown behavior only after confirming that the connected equipment cannot place a valid but unwanted signal on the receiver input. Automatic wakeup can therefore power the charge pump when the remote device activates. Verify that 1 µA shutdown behavior is compatible with the system’s leakage budget and that the power rail can support startup current when the interface wakes.
Informações de conformidade
RoHS details are shown in the MAX3221E comparison listing. No specific REACH, halogen-free, conflict-minerals, or automotive qualification statement is confirmed for this ordering code.