MAX3221EETE+T - 250kbps AutoShutdown RS-232 | Analog Devices
Артикул: MAX3221EETE+T ✓ АктивенMAX3221EETE+T Обзор
An RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and the bipolar, inverted signaling used by RS-232 equipment. It belongs to the interface IC hierarchy, where it bridges UART, UART-compatible controller, and peripheral circuitry with legacy or industrial communications ports. The MAX3221E supports the EIA/TIA-232 and V.28/V.24 signaling requirements identified for the MAX3221E family.
The MAX3221EETE+T combines a 250 kbps data rate with a 3.0V to 5.5V supply range, allowing operation alongside both 3.3V and 5V digital systems. Its AutoShutdown circuit recognizes when connected equipment is powered off or no valid signal appears on a receiver input, then disables the internal charge pump and drivers to reduce power consumption. Automatic wakeup restores operation when a valid signal returns.
The enhanced electrostatic-discharge design protects the transmitter outputs and receiver inputs against ±15 kV ESD events. This protection is particularly useful for cables connected to external equipment, where electrostatic discharge can enter through a connector rather than through the protected logic-side pins. The device converts one TTL or CMOS data channel into an RS-232 signal and converts one inbound RS-232 signal back into a logic-level output.
Typical uses include industrial serial adapters, test and measurement equipment, point-of-sale terminals, security systems, and embedded systems that retain an RS-232 port. The 250 kbps capability supports substantially faster communication than conventional low-speed RS-232 links, while the small TQFN package suits compact control boards. Systems requiring more than one RS-232 port normally require additional transceiver channels or a multichannel interface family.
When laying out the PCB, place the charge-pump capacitors and interface capacitors close to their designated pins, connect the exposed thermal pad to the ground plane, and keep the RS-232 traces away from sensitive clock, sensor, and analog signals. Confirm capacitor values, voltage ratings, and exposed-pad soldering requirements against the manufacturer datasheet before fabrication.
This product page combines the manufacturer interface specifications with package, sourcing, application, and replacement guidance. It also highlights practical ESD, layout, power-management, and signal-integrity considerations that engineers can apply when integrating the MAX3221EETE+T into a compact RS-232 circuit.
Аналоги без доработки для MAX3221EETE+T — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с MAX3221EETE+T (тот же форм-фактор и посадочное место) — отличается по Package, ESD Protection, Maximum Data Rate, Supply Voltage Range, AutoShutdown Supply Current.
MAX3221ECTE+T
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →MAX3221ECAE+T
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →MAX3221EEAE-T
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →MAX3221EETE+T Характеристики
| Product Type | RS-232 transceiver |
| Transceiver Configuration | 1 transmitter and 1 receiver |
| Duplex Mode | Full duplex |
| Supply Voltage Range | 3.0 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| ESD Protection | ±15 kV |
| Shutdown Supply Current | 1 µA |
| Power Management Feature | AutoShutdown with automatic wakeup |
| Communication Standard | EIA/TIA-232 and V.28/V.24 |
| Logic Interface | TTL/CMOS-compatible |
| Корпус | 16-pin TQFN with exposed pad |
| Package Dimensions | 5 mm × 5 mm |
| Тип монтажа | Surface mount |
| Количество выводов | 16 pins |
| Статус RoHS | RoHS details shown in comparison listings |
Руководство по цоколевке MAX3221EETE+T в корпусе 5 mm × 5 mm
Цоколевка для MAX3221EETE+T (корпус 5 mm × 5 mm). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для MAX3221EETE+T.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
MAX3221EETE+T подходит для 6 применениеs: Industrial Serial Adapters, Test and Measurement Equipment, Point-of-Sale Terminals, Security and Access Systems, Embedded Control Systems, RS-232-to-Logic Conversion.
Industrial Serial Adapters
The MAX3221EETE+T suits compact adapters that must bridge a 3.3V or 5V controller with an external RS-232 port. Its 250 kbps data-rate capability provides useful throughput for configuration transfer and diagnostic protocols, while ±15 kV interface protection improves resilience at the cable-facing pins. AutoShutdown reduces consumption to 1 µA when the connected equipment is inactive. The circuit should use the manufacturer-recommended charge-pump and interface capacitors, with the exposed pad connected to ground according to the TQFN land pattern.
Рекомендуется
Test and Measurement Equipment
The MAX3221EETE+T provides a compact logic-to-RS-232 path for programmable instruments, laboratory controllers, and service interfaces. At up to 250 kbps, it supports faster command exchange than basic serial links, while its 3.0V to 5.5V range permits operation from common instrumentation supply rails. The ±15 kV ESD rating is useful when users attach external cables. Keep the interface route away from precision analog sections and use the datasheet ground and charge-pump capacitor arrangement to minimize coupling.
Рекомендуется
Point-of-Sale Terminals
MAX3221EETE+T is suitable for point-of-sale equipment that communicates with a receipt printer, scanner, or service terminal over RS-232. The single full-duplex channel can carry commands and responses, and the 250 kbps rating handles common retail protocols efficiently. Automatic shutdown lowers power use when the peripheral is disconnected or inactive, while ESD protection adds protection at the external connector. Confirm connector pin assignment and cable signaling before placing the transceiver in the PCB layout.
Рекомендуется
Security and Access Systems
The MAX3221EETE+T can connect a security controller or access-control terminal to a legacy alarm panel, intercom, or configuration computer through RS-232. Its ±15 kV ESD protection is valuable when the interface reaches an external connector, and AutoShutdown supports low-power operation during idle periods. The 250 kbps rate is more than adequate for typical command and event traffic. Use the complete manufacturer pin table and exposed-pad layout, and keep unprotected logic-side routing away from the cable entry.
Рекомендуется
Embedded Control Systems
The MAX3221EETE+T provides a straightforward way for a 3.3V embedded controller to communicate with an RS-232 service port. Its 250 kbps capability supports firmware download and diagnostic traffic, and the automatic shutdown and wakeup behavior can reduce system load when no peripheral is connected. The 5 mm by 5 mm TQFN package preserves board area, although the exposed pad requires proper thermal-pad layout and soldering. Validate logic levels, UART baud tolerance, and isolation requirements during component selection.
Рекомендуется
RS-232-to-Logic Conversion
MAX3221EETE+T is appropriate for standalone level-conversion circuits that interface legacy RS-232 equipment with modern CMOS logic. One receiver translates the incoming bipolar signal, and one transmitter produces the corresponding outgoing RS-232 signal. Its 3.0V to 5.5V operating range supports common supply choices, while ±15 kV protection strengthens the cable-facing interface. Follow the manufacturer’s external-capacitor and charge-pump layout because incorrect values or long capacitor routes can impair startup and signal integrity.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MAX3221EETE+T — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MAX3221ECTE+T | MAX3221ECAE+T | MAX3221EEAE-T |
|---|---|---|---|---|
| Package | TQFN-16 with exposed pad | TQFN-16 with exposed pad | TQFN-16 with exposed pad | TQFN-16 with exposed pad |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Transceiver Configuration | 1 transmitter and 1 receiver | 1 transmitter and 1 receiver | 1 transmitter and 1 receiver | 1 transmitter and 1 receiver |
| Supply Voltage Range | 3.0 V to 5.5 V | 3.0 V to 5.5 V | 3.0 V to 5.5 V | 3.0 V to 5.5 V |
| Maximum Data Rate | 250 kbps | 250 kbps | 250 kbps | 250 kbps |
| ESD Protection | ±15 kV | ±15 kV | ±15 kV | ±15 kV |
| Shutdown Supply Current | 1 µA | 1 µA | 1 µA | 1 µA |
| Power Management | AutoShutdown with automatic wakeup | AutoShutdown with automatic wakeup | AutoShutdown with automatic wakeup | AutoShutdown with automatic wakeup |
| Communication Standard | EIA/TIA-232 and V.28/V.24 | EIA/TIA-232 and V.28/V.24 | EIA/TIA-232 and V.28/V.24 | EIA/TIA-232 and V.28/V.24 |
Ключевые отличия
- Maintains the MAX3221E 16-pin TQFN drop-in platform (против MAX3221ECTE+T)
- Combines 250 kbps operation with automatic power management (против MAX3221ECAE+T)
- Provides enhanced cable-side ESD protection (против MAX3221EEAE-T)
Заметки по проектированию
Place every charge-pump and interface capacitor directly between its designated pins and ground, using the shortest possible traces. The MAX3221E family uses internal switched-capacitor circuitry, so long capacitor connections can increase ringing, startup delay, and radiated noise. Follow the manufacturer PCB-layout example and keep the RS-232 traces short, away from clocks and analog inputs, and terminated according to the connected cable configuration.
Do not assume that any family member with a similar ordering code is automatically interchangeable. Confirm the 16-pin TQFN land pattern, exposed-pad connection, temperature grade, and tape-or-tube ordering requirement. The MAX3221ECTE+T, MAX3221ECAE+T, and MAX3221EEAE-T alternatives retain the same general interface ratings but their suffix differences may change environmental or packing requirements.
Keep the cable-facing RS-232 nets away from sensitive logic and analog traces, and provide a continuous ground reference beneath the interface area. Although the device includes ±15 kV ESD protection, protection is most effective when short connector-to-transceiver routes minimize surge current paths. If a cable crosses a board boundary, add the connector-side protection and grounding arrangement required by the system’s ESD and EMC architecture.
Use the MAX3221EETE+T AutoShutdown behavior only after confirming that the connected equipment cannot place a valid but unwanted signal on the receiver input. Automatic wakeup can therefore power the charge pump when the remote device activates. Verify that 1 µA shutdown behavior is compatible with the system’s leakage budget and that the power rail can support startup current when the interface wakes.
Информация о соответствии
RoHS details are shown in the MAX3221E comparison listing. No specific REACH, halogen-free, conflict-minerals, or automotive qualification statement is confirmed for this ordering code.