MAX3221EIPWE4 - 250kbps RS-232 Transceiver | Texas Instruments
N.º da peça: MAX3221EIPWE4 ✓ AtivoMAX3221EIPWE4 Visão geral
An RS-232 transceiver is an interface integrated circuit that converts logic-level signals into RS-232-compatible levels and converts received RS-232 signals back into logic levels. The MAX3221EIPWE4 belongs to the line-driver and receiver hierarchy within RS-232 interface ICs, combining one driver, one receiver with a dedicated enable input, and the voltage-conversion charge pumps required for single-supply operation.
The principal specifications include a 3 V to 5.5 V supply range, 250 kbps maximum data rate, one driver, one receiver, and operation from -40 °C to 85 °C. The E designation provides enhanced electrostatic-discharge protection, while the 16-TSSOP package supports compact surface-mount assemblies. A 500 mV receiver hysteresis helps prevent output chatter when the received signal is close to the decision threshold.
The dual charge-pump architecture allows the interface to generate the positive and negative voltage levels required by RS-232 without a negative supply input. Charge-pump capacitors and supply bypass capacitors should be placed close to their associated pins. The serial-port pins receive the enhanced ESD protection, helping improve robustness against electrostatic discharge encountered during exposed cable connections.
Typical applications include industrial serial adapters, programmable-logic-controller communication ports, test and measurement equipment, point-of-sale terminals, and embedded control systems that require a single RS-232 channel. The dedicated receiver-enable pin supports local control of receiver output state, which can simplify interface coordination in multi-function equipment.
The primary design trade-off is operating speed versus transmission distance. A 250 kbps transceiver is appropriate for moderate-speed serial links, but long cable runs and high data rates require careful baud-rate selection, grounding, shielding, and protection-network design. Confirm the pin functions and charge-pump values in the manufacturer datasheet before finalizing the PCB.
This page organizes the manufacturer specifications, sourcing fields, drop-in replacement findings, comparison parameters, and practical RS-232 interface design guidance. It is intended to help engineers evaluate the MAX3221EIPWE4 against same-footprint alternatives while preserving signal integrity and electrostatic-discharge protection requirements.
Alternativas drop-in para MAX3221EIPWE4 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com MAX3221EIPWE4 (mesmo formato e footprint) — diferindo em Maximum Data Rate, Package, Product Type, Supply Voltage Range.
MAX3221EIPW
✅ Drop-InConsulte o preço
Ver ficha técnica →MAX3221IPWR
✅ Drop-InConsulte o preço
Ver ficha técnica →MAX3221EIPWE4 Especificações
| Product Type | Single-channel RS-232 line driver/receiver transceiver |
| Number of Drivers | 1 driver |
| Number of Receivers | 1 receiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| Faixa de temperatura de operação | -40 °C to 85 °C |
| Receiver Hysteresis | 500 mV |
| Encapsulamento | 16-pin TSSOP, 4.40 mm width |
| Tipo de montagem | Surface mount |
| ESD Protection, Human Body Model | ±15 kV |
| ESD Protection, IEC Contact Discharge | ±8 kV |
| ESD Protection, IEC Air-Gap Discharge | ±15 kV |
| RS-232 Compliance | TIA/EIA-232-F |
| Charge-Pump Architecture | Dual charge-pump circuit |
| Receiver Enable | Dedicated enable pin |
| RoHS Compliance | 100% RoHS compliant |
| Lead-Free Status | Lead free |
Guia de Configuração de Pinos do MAX3221EIPWE4 16-pin tssop, 4.40 mm width
Configuração de pinos para MAX3221EIPWE4 (pacote 16-pin tssop, 4.40 mm width). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para MAX3221EIPWE4.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
MAX3221EIPWE4 é adequado para 6 aplicaçãos: Industrial RS-232 Control Ports, Programmable Logic Controller Communication, Test and Measurement Equipment, Point-of-Sale Terminal Interfaces, Embedded Serial Adapters, Legacy Equipment Communication.
Industrial RS-232 Control Ports
The MAX3221EIPWE4 fits single-port industrial control equipment that must translate a 3.3 V or 5 V controller into a RS-232 signal. Its 3 V to 5.5 V supply range supports both common logic rails, while the -40 °C to 85 °C rating covers demanding industrial environments. The one-driver, one-receiver arrangement is placed between the host UART and an external DB9 or terminal connector. For a 250-kbps link, the design should include the manufacturer-specified charge-pump capacitors, local supply bypassing, a solid ground reference, and cable-side transient protection where the line leaves the enclosure.
Recomendado
Programmable Logic Controller Communication
The MAX3221EIPWE4 provides a compact electrical interface between a PLC UART and a legacy RS-232 programming or monitoring port. Its 250-kbps maximum rate is suitable for common low-speed controller protocols, while the dual charge pumps eliminate the need for a separate negative supply rail. The receiver's 500 mV hysteresis improves noise margin on industrial wiring. Designers should keep the interface ground close to the transceiver ground reference, use a common return path with the cable, and avoid treating the enhanced on-chip ESD ratings as a substitute for properly coordinated external surge protection.
Recomendado
Test and Measurement Equipment
The MAX3221EIPWE4 is appropriate for a single RS-232 service or control channel in test and measurement equipment. The 3 V to 5.5 V operating range allows use beside modern instrumentation logic, and the 250-kbps rate is adequate for many legacy configuration and diagnostic protocols. The dedicated receiver-enable pin gives the host control over when the receiver output is active, which can simplify control of a shared connector. A robust implementation follows the datasheet's charge-pump and bypass layouts and adds series impedance or surge protection for bench leads connected to long or noisy cables.
Recomendado
Point-of-Sale Terminal Interfaces
The MAX3221EIPWE4 can interface a point-of-sale terminal or peripheral that still uses RS-232 for receipt printers, scanners, or service connectors. Its 250-kbps data rate covers typical peripheral traffic, while operation from 3.3 V reduces the power-supply burden in compact equipment. The 16-TSSOP package preserves PCB area compared with larger RS-232 implementations. Because peripherals often use long or externally routed cables, the connector side should include coordinated overvoltage and surge protection, while signal-ground continuity must be maintained to avoid receiver errors.
Recomendado
Embedded Serial Adapters
The MAX3221EIPWE4 suits compact embedded systems that must add one RS-232 port to a 3.3 V processor, microcontroller, or programmable logic controller. Its dual charge-pump design converts a single positive supply into the bipolar RS-232 levels, reducing external power complexity. The device operates at up to 250 kbps and provides a dedicated receiver-enable control for host-managed signaling. Board implementation should reserve the required charge-pump and bypass capacitor positions, maintain short return paths, and use a protected connector when the adapter is used as a field-accessible peripheral.
Recomendado
Legacy Equipment Communication
The MAX3221EIPWE4 allows modern control electronics to communicate with legacy RS-232 equipment while retaining a compact surface-mount implementation. Its 250-kbps rate supports many configuration, status, and command links, and its 500 mV receiver hysteresis helps reject noise around the input transition region. For reliable integration, use the manufacturer's recommended charge-pump capacitance and power-bypass arrangement, connect the cable shield according to the enclosure strategy, and confirm that the legacy equipment's ground and voltage levels do not require isolation. A dedicated receiver-enable signal may also be useful for port-sharing behavior.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para MAX3221EIPWE4 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | MAX3221EIPW | MAX3221IPWR |
|---|---|---|---|
| Package | 16-TSSOP | 16-TSSOP | 16-TSSOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Transceiver Configuration | 1 driver / 1 receiver | 1 driver / 1 receiver | 1 driver / 1 receiver |
| Maximum Data Rate | 250 kbps | 250 kbps | 250 kbps |
| RS-232 Standard | TIA/EIA-232-F | RS-232 line driver/receiver | RS-232 line driver/receiver |
Principais diferenciais
- Lower minimum supply voltage (vs MAX3221IPWR)
- Specified industrial temperature range (vs MAX3221EIPW)
- Enhanced serial-port ESD ratings (vs MAX3221IPWR)
- Same-footprint upgrade path (vs MAX3221EIPW)
Notas de projeto
Place the charge-pump capacitors and local supply-bypass capacitors close to their specified pins, using the shortest practical ground-return paths. The MAX3221 generates bipolar RS-232 levels through charge pumps, so long capacitor traces and high-resistance ground connections can degrade signal timing and increase emissions. Follow the manufacturer datasheet layout and component values, and keep the serial connector and analog or high-speed circuitry physically separated to minimize coupling.
Do not substitute a nominal 5 V RS-232 transceiver in a 3.3 V design without confirming its minimum supply voltage. The MAX3221EIPWE4 operates from 3 V to 5.5 V, while the MAX3221IPWR is listed with a 4.5 V to 5.5 V range. Also verify the receiver-enable polarity and the complete 16-pin TSSOP pinout before substituting a related orderable code; a matching package outline alone does not guarantee identical environmental or commercial suffixes.
Use the 500 mV receiver hysteresis to improve rejection of noise near the receiver threshold, but also control the physical cable path. Maintain a continuous signal-ground return, use suitable twisted-pair cabling for exposed RS-232 links, and terminate or protect connector pins according to the installation's surge environment. At 250 kbps, edge quality and ground bounce become increasingly important as cable length and data rate increase.
Keep the RS-232 connector and charge-pump region away from clocks, switching supplies, ADC inputs, and sensitive analog nodes. Maintain a compact high-frequency return path and observe the datasheet's component-placement guidance to limit charge-pump ripple from coupling into adjacent circuitry. If the interface drives a long cable, combine correct grounding with connector-side surge protection rather than relying only on the transceiver's integrated ESD capability.
Informações de conformidade
The product listing identifies the MAX3221EIPWE4 as 100% RoHS compliant and lead free. No explicit REACH, AEC-Q100, halogen-free, or conflict-minerals status was identified for this exact orderable MPN.