MSP430F6723IPN - 25MHz 64KB Flash Metering SoC | Texas Instruments
N.º da peça: MSP430F6723IPN ✓ AtivoMSP430F6723IPN Visão geral
A metering SoC is a specialized mixed-signal microcontroller that integrates measurement, computation, communication, and user-interface functions needed by energy meters and similar embedded systems. The MSP430 architecture belongs to the hierarchy of microcontrollers, embedded processors, and general-purpose semiconductor ICs. Its mixed-signal feature set is intended to simplify systems that measure low-frequency electrical signals while retaining the low-power behavior associated with the MSP430 family.
The device provides two 24-bit sigma-delta ADCs, an LCD driver with integrated contrast control, and a real-time-clock module with alarm capabilities. Supporting communication and timing resources include three enhanced USCI_A modules, one enhanced USCI_B module, four 16-bit timers, a hardware multiplier, and a DMA module. These resources allow sensor inputs, energy measurements, timekeeping, communications, and local display control to be handled within one embedded architecture.
MSP430F6723IPN operates from 2.5 V or 3.3 V, as identified for the specified orderable device, and supports an industrial temperature range of -40°C to 85°C. Its 64 KB flash provides program storage for metering algorithms and communication firmware, while 4 KB of RAM supports working data and protocol processing. The 80-pin LQFP body is 12 mm by 12 mm and is suitable for inspection, rework, and conventional PCB assembly.
Typical uses include single-phase electricity meters, smart energy meters, utility load monitoring, industrial energy-management terminals, low-power sensing nodes, and metering equipment requiring an LCD and real-time clock. The integrated sigma-delta ADCs are particularly useful for slowly varying, high-resolution measurements, while the USCI peripherals support serial communication to local sensors, meters, or service interfaces.
PCB design should preserve clean analog signal paths around the ADC inputs and provide suitable grounding and decoupling between the metering and digital sections. Firmware must also validate clock accuracy, LCD timing, ADC channel configuration, and RTC behavior across the intended operating range. Use the TI datasheet and device pin-description tables when assigning tracks and defining the board footprint.
This product summary combines the manufacturer’s device description with practical guidance on partitioning analog and digital circuitry, validating firmware behavior, and evaluating the MSP430F6723IPN for single-phase metering systems. The available manufacturer and distributor pages provide the primary documentation for ordering information, package details, and lifecycle status.
Alternativas drop-in para MSP430F6723IPN — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
MSP430F6723AIPN
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
MSP430F6724IPZR
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
MSP430F6723IPN Classificações máximas e características elétricas
| Product Type | Single-phase metering SoC |
| CPU Architecture | 16-bit MSP430 CPUXV2 RISC |
| Frequência máxima de clock | 25 MHz |
| Flash Memory | 64 KB (64K x 8) |
| RAM Memory | 4 KB |
| Sigma-Delta ADC Count | 2 |
| Sigma-Delta ADC Resolution | 24-bit |
| Additional ADC | 10-bit ADC |
| Enhanced USCI_A Modules | 3 |
| Enhanced USCI_B Modules | 1 |
| Timer Count | 4 timers with 16-bit resolution |
| Real-Time Clock | Present, with alarm capabilities |
| LCD Driver | Present, with integrated contrast control |
| DMA Module | Present |
| Hardware Multiplier | Present |
| Tensão de alimentação | 2.5 V or 3.3 V |
| Temperatura de operação | -40°C to 85°C |
| Encapsulamento | 80-pin LQFP (PN), 12 mm x 12 mm |
| Tipo de montagem | Surface mount |
| RoHS Compliance | unknown |
| REACH Compliance | unknown |
| AEC-Q100 Qualification | unknown |
Guia de Configuração de Pinos do MSP430F6723IPN 80-pin lqfp (pn), 12 mm x 12 mm
Configuração de pinos para MSP430F6723IPN (pacote 80-pin lqfp (pn), 12 mm x 12 mm). Este CI digital inclui GPIO, interfaces de comunicação (UART, SPI, I2C) e pinos de alimentação. Consulte o datasheet do fabricante para funções alternativas dos pinos e opções de configuração. Essencial para projeto de sistemas embarcados e layout de PCB.
Nenhum dado detalhado de pinagem disponível para MSP430F6723IPN.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
MSP430F6723IPN é adequado para 6 aplicaçãos: Single-Phase Smart Electricity Meters, Utility Load Monitoring Terminals, Smart Energy-Management Gateways, Industrial Energy Sensors, LCD-Enabled Environmental Monitoring, Time-Based Data Acquisition Systems.
Single-Phase Smart Electricity Meters
MSP430F6723IPN fits single-phase smart meters because it combines a 25 MHz 16-bit MSP430 processor with two 24-bit sigma-delta ADCs in one metering SoC. The ADCs support high-resolution acquisition of slowly varying electrical signals, while the hardware multiplier and DMA improve the handling of metering calculations and sampled data. Its 64 KB flash stores measurement, calibration, and communications firmware, and the 4 KB RAM accommodates working buffers and protocol state. The integrated RTC with alarm capabilities supports time stamping, tariff schedules, and periodic sampling. Compared with a discrete measurement-and-control design, the integrated ADC, LCD driver, timers, and serial interfaces reduce the number of supporting components and simplify board partitioning. Final qualification must verify input protection, metrology accuracy, isolation, EMC behavior, and the exact calibration workflow required by the meter specification.
Recomendado
Utility Load Monitoring Terminals
MSP430F6723IPN can serve as the control and measurement core of a compact utility load-monitoring terminal. Two 24-bit sigma-delta ADCs provide measurement channels for the analog front end, while four 16-bit timers support timebase and sampling functions. The 25 MHz MSP430 CPU provides sufficient throughput for calibration, event handling, local data processing, and communication firmware within the 64 KB flash and 4 KB RAM limits. Three eUSCI_A modules and one eUSCI_B module allow the terminal to connect serial sensors, service interfaces, or a communications transceiver. The LCD driver supports an operator display without a separate display controller, and the RTC with alarms enables scheduled logging. A practical design should isolate the metering analog section from switching and communications circuitry, while the RTC accuracy and low-power behavior must be evaluated against the target reporting interval.
Recomendado
Smart Energy-Management Gateways
MSP430F6723IPN is suitable for edge energy-management nodes that acquire measurements and control a local display or downstream communications interface. Its two 24-bit sigma-delta ADCs are appropriate for precision acquisition from transducer and sensing circuits, while DMA can transfer sampled data without burdening the CPU. The three eUSCI_A and one eUSCI_B peripherals support a mixture of UART, SPI, or I2C links when configured for those functions. The 64 KB flash and 4 KB RAM are sufficient for compact metering logic and communication stacks, although application code and protocol buffer requirements must be checked. The LCD driver and RTC simplify human-readable status displays and scheduled operations. When designing a gateway, provide local decoupling and careful ground partitioning around the ADC circuitry, and use the eUSCI pin multiplexing table to avoid conflicts with LCD, debug, and auxiliary functions.
Recomendado
Industrial Energy Sensors
MSP430F6723IPN can support industrial energy sensors that require accurate signal acquisition, deterministic timing, and flexible serial connectivity. The two 24-bit sigma-delta ADCs suit transducer outputs and low-bandwidth measurement channels, while the four 16-bit timers and DMA module help coordinate sampling, pulse counting, and data transfer. A 25 MHz CPU provides useful processing headroom for filtering, calibration, and diagnostics within the device’s 64 KB flash and 4 KB RAM. If a local display is needed, the integrated LCD driver reduces external controller overhead; if not, the available serial modules can be assigned to sensors and industrial communications. The -40°C to 85°C operating range is appropriate for many industrial environments, although enclosure temperature, power-supply tolerance, and EMC requirements still require system-level validation. ADC reference routing, guard structures, and separation from high-current switching stages are especially important in energy-measurement layouts.
Recomendado
LCD-Enabled Environmental Monitoring
MSP430F6723IPN can implement a local sensing and display node when the design needs a low-power MSP430 controller, precision analog inputs, and an LCD. The two sigma-delta ADCs can acquire outputs from suitable environmental or process sensors, while the four timers provide periodic measurement and display-update timing. The 64 KB flash accommodates application firmware and display data, and the 4 KB RAM supports acquired samples and communication buffers. The integrated LCD controller with contrast control can simplify a human-machine interface for industrial panels, while the RTC with alarms enables scheduled readings and event logs. The three eUSCI_A and one eUSCI_B modules can connect selected sensors or a host interface. Designers should confirm the LCD segment count and voltage requirements against the device specifications, verify sensor bandwidth requirements before choosing sigma-delta conversion, and keep LCD and switching-supply routing away from sensitive analog inputs.
Recomendado
Time-Based Data Acquisition Systems
MSP430F6723IPN suits compact acquisition systems that combine a real-time clock, programmable timers, DMA, and high-resolution analog conversion. The RTC with alarm capabilities can initiate scheduled measurements, while the four 16-bit timers support sampling cadence, timeout, and pulse-measurement tasks. Two 24-bit sigma-delta ADCs are most effective for low-frequency or narrow-band signals rather than high-speed waveform acquisition. The hardware multiplier supports efficient arithmetic in filtering and scaling routines, while DMA reduces interrupt-driven data movement. Firmware can store event histories in the 64 KB flash and use the 4 KB RAM for acquisition buffers, although sustained logging rates require a capacity calculation. The RTC provides a time reference, but long-term accuracy depends on the crystal source, load capacitance, layout, and calibration strategy. Use the manufacturer timing and clock-tree documentation when assigning timers and programming the RTC.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para MSP430F6723IPN — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | MSP430F6723AIPN | MSP430F6724IPZR |
|---|---|---|---|
| Package | 80-pin LQFP (PN), 12 mm x 12 mm | 80-pin LQFP (PN) | 80-pin LQFP family option; exact ZR footprint requires confirmation |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Product Category | Single-phase metering SoC | Single-phase metering SoC | MSP430F672x mixed-signal microcontroller |
| CPU Architecture | 16-bit MSP430 CPUXV2 | 16-bit MSP430 | 16-bit MSP430 |
| LCD Driver | Present, with integrated contrast control | Present | Present in MSP430F672x family |
| Real-Time Clock | Present, with alarm capabilities | Present | Present in MSP430F672x family |
Principais diferenciais
- Metering-focused mixed-signal integration (vs MSP430F5529IPNR)
- Dedicated high-resolution measurement channels (vs MSP430F6724IPZR)
- Direct single-phase metering positioning (vs MSP430F5521IPN)
Notas de projeto
Keep the sigma-delta ADC input paths short, controlled, and away from LCD drive, communication edges, and switching-supply nodes. Follow the manufacturer’s recommended analog grounding and reference layout from the datasheet, including the treatment of AVSS and the device ground pins. A single solid ground plane is often preferable to fragmented return paths, but partition high-current switching returns so they do not cross the measurement area. Confirm the exposed-package and thermal-land requirements directly against the TI package drawing before releasing the PCB footprint.
Use the TI power-supply connection and decoupling guidance for the 2.5 V or 3.3 V operating condition selected for the design. Place required bulk and high-frequency decoupling capacitors at the corresponding supply pins, with the shortest possible current loops and an unobstructed return path. The ADC reference and auxiliary supply pins must receive the values and filtering required by the datasheet. Validate startup sequencing, voltage tolerance, and measured noise because marginal reference supply can affect meter accuracy even when the main digital rail is within specification.
Do not treat the MSP430F6723A and MSP430F6724IPZR candidates as automatic drop-in devices. Their family relationship supports close functional evaluation, but package drawings, terminal assignments, ADC channels, memory configuration, and peripheral multiplexing must be checked against the manufacturer documentation. Preserve the original MSP430F6723IPN footprint only after a complete schematic and firmware review. For production, verify the exact orderable suffix, pin count, package body size, and programming configuration.
Two 24-bit sigma-delta ADCs do not make the device suitable for arbitrary high-speed waveform acquisition. Confirm input bandwidth, sample rate, digital filter response, latency, and acquisition time for each analog channel. Likewise, the RTC, LCD, timers, DMA, and four serial modules share a finite peripheral-pin set. Build the peripheral-allocation matrix early so display segments, communications, debug functions, analog inputs, and timer outputs do not conflict.
Informações de conformidade
The available manufacturer and distributor summaries do not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Use the current TI environmental-compliance information and material declaration for procurement decisions.