Texas Instruments

MSP430F6723IPN - 25MHz 64KB Flash Metering SoC | Texas Instruments

MPN: MSP430F6723IPN ✓ 啟用中
2.5 V or 3.3 V Vdss 80-pin LQFP (PN), 12 mm x 12 mm Package 25 MHz Speed 64 KB (64K x 8) Memory
MOQ: 1 |

MSP430F6723IPN 概覽

Texas Instruments MSP430F6723IPN is a single-phase metering system-on-chip with a 16-bit MSP430 CPU, 25 MHz maximum clock speed, 64 KB flash memory, 4 KB RAM, two sigma-delta ADCs, an LCD driver, and a real-time clock in an 80-pin LQFP (PN) package. It combines mixed-signal acquisition, embedded control, display support, and metering-specific peripherals in one low-power device.

A metering SoC is a specialized mixed-signal microcontroller that integrates measurement, computation, communication, and user-interface functions needed by energy meters and similar embedded systems. The MSP430 architecture belongs to the hierarchy of microcontrollers, embedded processors, and general-purpose semiconductor ICs. Its mixed-signal feature set is intended to simplify systems that measure low-frequency electrical signals while retaining the low-power behavior associated with the MSP430 family.

The device provides two 24-bit sigma-delta ADCs, an LCD driver with integrated contrast control, and a real-time-clock module with alarm capabilities. Supporting communication and timing resources include three enhanced USCI_A modules, one enhanced USCI_B module, four 16-bit timers, a hardware multiplier, and a DMA module. These resources allow sensor inputs, energy measurements, timekeeping, communications, and local display control to be handled within one embedded architecture.

MSP430F6723IPN operates from 2.5 V or 3.3 V, as identified for the specified orderable device, and supports an industrial temperature range of -40°C to 85°C. Its 64 KB flash provides program storage for metering algorithms and communication firmware, while 4 KB of RAM supports working data and protocol processing. The 80-pin LQFP body is 12 mm by 12 mm and is suitable for inspection, rework, and conventional PCB assembly.

Typical uses include single-phase electricity meters, smart energy meters, utility load monitoring, industrial energy-management terminals, low-power sensing nodes, and metering equipment requiring an LCD and real-time clock. The integrated sigma-delta ADCs are particularly useful for slowly varying, high-resolution measurements, while the USCI peripherals support serial communication to local sensors, meters, or service interfaces.

PCB design should preserve clean analog signal paths around the ADC inputs and provide suitable grounding and decoupling between the metering and digital sections. Firmware must also validate clock accuracy, LCD timing, ADC channel configuration, and RTC behavior across the intended operating range. Use the TI datasheet and device pin-description tables when assigning tracks and defining the board footprint.

This product summary combines the manufacturer’s device description with practical guidance on partitioning analog and digital circuitry, validating firmware behavior, and evaluating the MSP430F6723IPN for single-phase metering systems. The available manufacturer and distributor pages provide the primary documentation for ordering information, package details, and lifecycle status.

直接替換替代品,適用於 MSP430F6723IPN — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

MSP430F6723AIPN

✅ 直接替換
📦 80-pin LQFP (PN)
Newer MSP430F6723A family revision with the same 16-bit MSP430 and 80-pin PN package designation; ADC count, memory details, and terminal mapping require verification.

📋 參考替代品(不在目錄中)

MSP430F6724IPZR

✅ 直接替換
📦 80-pin LQFP (PN)
Related MSP430F672x metering device with up to three 24-bit sigma-delta ADCs versus two for MSP430F6723; ZR pin mapping and exact package compatibility require verification.

📋 參考替代品(不在目錄中)

MSP430F6723IPN 最大額定值與電氣特性

Product Type Single-phase metering SoC
CPU Architecture 16-bit MSP430 CPUXV2 RISC
最大時脈頻率 25 MHz
Flash Memory 64 KB (64K x 8)
RAM Memory 4 KB
Sigma-Delta ADC Count 2
Sigma-Delta ADC Resolution 24-bit
Additional ADC 10-bit ADC
Enhanced USCI_A Modules 3
Enhanced USCI_B Modules 1
Timer Count 4 timers with 16-bit resolution
Real-Time Clock Present, with alarm capabilities
LCD Driver Present, with integrated contrast control
DMA Module Present
Hardware Multiplier Present
供應電壓 2.5 V or 3.3 V
工作溫度 -40°C to 85°C
封裝 80-pin LQFP (PN), 12 mm x 12 mm
安裝類型 Surface mount
RoHS Compliance unknown
REACH Compliance unknown
AEC-Q100 Qualification unknown

MSP430F6723IPN 80-pin lqfp (pn), 12 mm x 12 mm 腳位配置指南

MSP430F6723IPN(80-pin lqfp (pn), 12 mm x 12 mm 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。

MSP430F6723IPN 的 80-pin lqfp (pn), 12 mm x 12 mm 封裝腳位圖

無詳細腳位定義資料: MSP430F6723IPN.

請參閱 資料表 以查看完整腳位配置。

典型應用

MSP430F6723IPN 適用於 6 應用s: Single-Phase Smart Electricity Meters, Utility Load Monitoring Terminals, Smart Energy-Management Gateways, Industrial Energy Sensors, LCD-Enabled Environmental Monitoring, Time-Based Data Acquisition Systems.

⚡

Single-Phase Smart Electricity Meters

MSP430F6723IPN fits single-phase smart meters because it combines a 25 MHz 16-bit MSP430 processor with two 24-bit sigma-delta ADCs in one metering SoC. The ADCs support high-resolution acquisition of slowly varying electrical signals, while the hardware multiplier and DMA improve the handling of metering calculations and sampled data. Its 64 KB flash stores measurement, calibration, and communications firmware, and the 4 KB RAM accommodates working buffers and protocol state. The integrated RTC with alarm capabilities supports time stamping, tariff schedules, and periodic sampling. Compared with a discrete measurement-and-control design, the integrated ADC, LCD driver, timers, and serial interfaces reduce the number of supporting components and simplify board partitioning. Final qualification must verify input protection, metrology accuracy, isolation, EMC behavior, and the exact calibration workflow required by the meter specification.

🏭

Utility Load Monitoring Terminals

MSP430F6723IPN can serve as the control and measurement core of a compact utility load-monitoring terminal. Two 24-bit sigma-delta ADCs provide measurement channels for the analog front end, while four 16-bit timers support timebase and sampling functions. The 25 MHz MSP430 CPU provides sufficient throughput for calibration, event handling, local data processing, and communication firmware within the 64 KB flash and 4 KB RAM limits. Three eUSCI_A modules and one eUSCI_B module allow the terminal to connect serial sensors, service interfaces, or a communications transceiver. The LCD driver supports an operator display without a separate display controller, and the RTC with alarms enables scheduled logging. A practical design should isolate the metering analog section from switching and communications circuitry, while the RTC accuracy and low-power behavior must be evaluated against the target reporting interval.

🌐

Smart Energy-Management Gateways

MSP430F6723IPN is suitable for edge energy-management nodes that acquire measurements and control a local display or downstream communications interface. Its two 24-bit sigma-delta ADCs are appropriate for precision acquisition from transducer and sensing circuits, while DMA can transfer sampled data without burdening the CPU. The three eUSCI_A and one eUSCI_B peripherals support a mixture of UART, SPI, or I2C links when configured for those functions. The 64 KB flash and 4 KB RAM are sufficient for compact metering logic and communication stacks, although application code and protocol buffer requirements must be checked. The LCD driver and RTC simplify human-readable status displays and scheduled operations. When designing a gateway, provide local decoupling and careful ground partitioning around the ADC circuitry, and use the eUSCI pin multiplexing table to avoid conflicts with LCD, debug, and auxiliary functions.

🏭

Industrial Energy Sensors

MSP430F6723IPN can support industrial energy sensors that require accurate signal acquisition, deterministic timing, and flexible serial connectivity. The two 24-bit sigma-delta ADCs suit transducer outputs and low-bandwidth measurement channels, while the four 16-bit timers and DMA module help coordinate sampling, pulse counting, and data transfer. A 25 MHz CPU provides useful processing headroom for filtering, calibration, and diagnostics within the device’s 64 KB flash and 4 KB RAM. If a local display is needed, the integrated LCD driver reduces external controller overhead; if not, the available serial modules can be assigned to sensors and industrial communications. The -40°C to 85°C operating range is appropriate for many industrial environments, although enclosure temperature, power-supply tolerance, and EMC requirements still require system-level validation. ADC reference routing, guard structures, and separation from high-current switching stages are especially important in energy-measurement layouts.

📺

LCD-Enabled Environmental Monitoring

MSP430F6723IPN can implement a local sensing and display node when the design needs a low-power MSP430 controller, precision analog inputs, and an LCD. The two sigma-delta ADCs can acquire outputs from suitable environmental or process sensors, while the four timers provide periodic measurement and display-update timing. The 64 KB flash accommodates application firmware and display data, and the 4 KB RAM supports acquired samples and communication buffers. The integrated LCD controller with contrast control can simplify a human-machine interface for industrial panels, while the RTC with alarms enables scheduled readings and event logs. The three eUSCI_A and one eUSCI_B modules can connect selected sensors or a host interface. Designers should confirm the LCD segment count and voltage requirements against the device specifications, verify sensor bandwidth requirements before choosing sigma-delta conversion, and keep LCD and switching-supply routing away from sensitive analog inputs.

🧩

Time-Based Data Acquisition Systems

MSP430F6723IPN suits compact acquisition systems that combine a real-time clock, programmable timers, DMA, and high-resolution analog conversion. The RTC with alarm capabilities can initiate scheduled measurements, while the four 16-bit timers support sampling cadence, timeout, and pulse-measurement tasks. Two 24-bit sigma-delta ADCs are most effective for low-frequency or narrow-band signals rather than high-speed waveform acquisition. The hardware multiplier supports efficient arithmetic in filtering and scaling routines, while DMA reduces interrupt-driven data movement. Firmware can store event histories in the 64 KB flash and use the 4 KB RAM for acquisition buffers, although sustained logging rates require a capacity calculation. The RTC provides a time reference, but long-term accuracy depends on the crystal source, load capacitance, layout, and calibration strategy. Use the manufacturer timing and clock-tree documentation when assigning timers and programming the RTC.

推薦產品摘要

MSP430F6723A Newer single-phase metering SoC family candidate 用於: Single-Phase Smart Electricity Meters, Utility Load Monitoring Terminals, Smart Energy-Management Gateways, Industrial Energy Sensors, LCD-Enabled Environmental Monitoring, Time-Based Data Acquisition Systems MSP430F6724IPZR Related MSP430F672x metering device 用於: Single-Phase Smart Electricity Meters, Time-Based Data Acquisition Systems MSP430F5521IPN Texas Instruments 用於: Utility Load Monitoring Terminals, LCD-Enabled Environmental Monitoring MSP430F5529IPNR Texas Instruments 用於: Smart Energy-Management Gateways, Industrial Energy Sensors
What is the MSP430F6723IPN?
The MSP430F6723IPN is a Texas Instruments single-phase metering system-on-chip built around a 16-bit MSP430 CPU. It combines two 24-bit sigma-delta ADCs, 64 KB of flash, 4 KB of RAM, an LCD driver, and a real-time clock in an 80-pin LQFP package. According to the manufacturer product page, these resources target energy-metering and other low-power mixed-signal systems.
What are the key specifications of MSP430F6723IPN?
MSP430F6723IPN combines a 25 MHz 16-bit MSP430 CPU, 64 KB of flash, 4 KB of RAM, two 24-bit sigma-delta ADCs, and a 10-bit ADC. The device also includes three eUSCI_A modules, one eUSCI_B module, four 16-bit timers, DMA, a hardware multiplier, an LCD driver, and an RTC with alarms. The manufacturer describes it as a single-phase metering SoC operating in an 80-pin LQFP package.
What is the operating voltage of MSP430F6723IPN?
MSP430F6723IPN supports 2.5 V and 3.3 V supply operation for the specified orderable device. The manufacturer ordering information identifies the PN-package variant, while distributor technical listings identify the device as a 2.5 V or 3.3 V mixed-signal microcontroller. Verify the exact power rails, decoupling values, and analog operating conditions against the TI datasheet before finalizing the power supply.
Where can I download the MSP430F6723IPN datasheet PDF?
The official MSP430F6723 datasheet is available through Texas Instruments at https://www.ti.com/lit/gpn/MSP430F6723. The manufacturer product page at https://www.ti.com/product/MSP430F6723 provides parameters, ordering information, quality information, and links to supporting documents. Use the manufacturer PDF for the authoritative pin descriptions, electrical limits, timing requirements, and application guidance.
Where can I find the MSP430F6723IPN pinout?
The MSP430F6723IPN pinout is found in the pin-description table of the TI MSP430F6723 datasheet, available from the manufacturer’s official document link. The device uses an 80-pin LQFP package designated PN by Texas Instruments. Use the datasheet’s terminal-number diagram and signal descriptions when assigning analog inputs, communication ports, LCD outputs, power pins, grounds, and test points.
Is MSP430F6723IPN suitable for a single-phase smart meter?
MSP430F6723IPN is specifically positioned for single-phase metering because it integrates two 24-bit sigma-delta ADCs, metering-oriented computation, an LCD driver, and a real-time clock with alarms. Its 64 KB flash and 4 KB RAM support firmware, measurement processing, and display or communications routines. The final design still requires validation of input bandwidth, accuracy, safety isolation, and metrology requirements for the specific product.
MSP430F6723IPN vs MSP430F6723A — which should I choose?
MSP430F6723A is the newer TI product family associated with the same single-phase metering function, while MSP430F6723IPN is the specified orderable device with 64 KB flash and 4 KB RAM. Both are 16-bit MSP430 solutions targeted at metering designs, but firmware, ordering, and device-status details should be checked on their separate TI product pages. Do not assume revision equivalence without reviewing the manufacturer documentation.
What is the difference between MSP430F6723IPN and MSP430F6724IPZR?
MSP430F6723IPN is the 80-pin PN-package variant with two sigma-delta ADCs, while MSP430F6724IPZR belongs to the related MSP430F672x family and uses a different ZR package designation. The family documentation notes support for up to three high-performance sigma-delta ADCs across the combined MSP430F673x and MSP430F672x families. Because package and ADC configurations differ, MSP430F6724IPZR is not a confirmed drop-in replacement.
When should I choose MSP430F6723IPN over MSP430F5529IPNR?
Choose MSP430F6723IPN when the design specifically benefits from its metering-oriented integration: two 24-bit sigma-delta ADCs, an LCD driver, and an RTC with alarm capabilities. MSP430F5529IPNR is identified as a related 16-bit, 25 MHz, 80-pin MSP430 option, but it is not confirmed as a pin-to-pin functional match. Select it only after comparing its ADC architecture, memory, peripherals, pin assignments, and firmware requirements.
What can replace MSP430F6723IPN?
No drop-in replacement for MSP430F6723IPN is confirmed by the available manufacturer and cross-reference information. MSP430F6723A is the closest newer TI family candidate, but it must be evaluated as a redesign rather than treated as a verified drop-in part. Verify package dimensions, terminal assignments, ADC inputs, LCD mapping, supply requirements, memory organization, and firmware compatibility before selecting any replacement.
Is MSP430F5521IPN a drop-in replacement for MSP430F6723IPN?
MSP430F5521IPN should not be assumed to be a drop-in replacement for MSP430F6723IPN. Although both are TI 16-bit MSP430 devices associated with 80-pin LQFP options, the available comparison result does not establish identical terminal assignments or metering peripherals. Treat MSP430F5521IPN as a functional alternative requiring a complete hardware and software review, not as a footprint-compatible substitute.
Where can I buy MSP430F6723IPN online?
Use the Request a Quote form on this page to request MSP430F6723IPN availability, current commercial terms, and a traceable quotation from XAIPART. The manufacturer product page also provides ordering information for the PN-package device. Because prices and inventory can change by quantity and market conditions, a current quotation is the appropriate method for confirming supply, MOQ, and delivery.
What is the lead time for MSP430F6723IPN?
The current MSP430F6723IPN lead time should be confirmed through the Request a Quote form on this page. Texas Instruments lists the MSP430F6723IPN as an orderable PN-package device, but ordering status alone does not establish a fixed delivery interval. For production planning, request current stock, factory lead time, MOQ, and available shipment quantities for the exact 80-pin PN orderable part.
Is MSP430F6723IPN in stock?
Current MSP430F6723IPN stock should be confirmed through the Request a Quote form on this page. Marketplace search results can reflect changing inventory, authorized-channel quantities, or different orderable suffixes, so they should not be treated as a guaranteed allocation. Specify the required quantity, packaging method, and permitted manufacturer date codes when requesting the quotation.
Does MSP430F6723IPN meet RoHS and REACH requirements?
The MSP430F6723IPN compliance status is not established by the available product summaries, so RoHS, REACH, lead-free, halogen-free, and conflict-minerals status remain unknown. Use the TI product page’s environmental-compliance controls and the manufacturer’s current material declaration for an authoritative procurement decision. Do not infer compliance solely from the device’s RoHS-era availability or packaging format.

工程參考資料,適用於 MSP430F6723IPN — 比較、設計指引及合規資訊。

選型指南

Choose MSP430F6723IPN for a new single-phase metering design that benefits from two 24-bit sigma-delta ADCs, a 25 MHz 16-bit MSP430 CPU, 64 KB flash, 4 KB RAM, an LCD controller, and an alarm-capable RTC in an 80-pin LQFP package. It is especially suitable when measurement accuracy, local metering, and compact integration matter more than maximum code or RAM capacity. Consider MSP430F6723AIPN when you need the newer TI family and have completed a pin, memory, peripheral, and firmware comparison. Consider MSP430F6724IPZR when the design can benefit from the additional ADC capacity found in the broader MSP430F672x family. MSP430F5521IPN and MSP430F5529IPNR should be treated as redesign candidates rather than drop-in replacements because equivalent terminal mappings and metering peripherals have not been established. For any substitution, review the TI datasheets, package drawings, peripheral mux tables, ADC specifications, and required code changes before PCB release.

與替代品比較

參數 本產品 MSP430F6723AIPN MSP430F6724IPZR
Package 80-pin LQFP (PN), 12 mm x 12 mm 80-pin LQFP (PN) 80-pin LQFP family option; exact ZR footprint requires confirmation
Brand Texas Instruments Texas Instruments Texas Instruments
Product Category Single-phase metering SoC Single-phase metering SoC MSP430F672x mixed-signal microcontroller
CPU Architecture 16-bit MSP430 CPUXV2 16-bit MSP430 16-bit MSP430
LCD Driver Present, with integrated contrast control Present Present in MSP430F672x family
Real-Time Clock Present, with alarm capabilities Present Present in MSP430F672x family

主要差異化特點

  • Metering-focused mixed-signal integration (對比MSP430F5529IPNR)
  • Dedicated high-resolution measurement channels (對比MSP430F6724IPZR)
  • Direct single-phase metering positioning (對比MSP430F5521IPN)

設計說明

Keep the sigma-delta ADC input paths short, controlled, and away from LCD drive, communication edges, and switching-supply nodes. Follow the manufacturer’s recommended analog grounding and reference layout from the datasheet, including the treatment of AVSS and the device ground pins. A single solid ground plane is often preferable to fragmented return paths, but partition high-current switching returns so they do not cross the measurement area. Confirm the exposed-package and thermal-land requirements directly against the TI package drawing before releasing the PCB footprint.

Use the TI power-supply connection and decoupling guidance for the 2.5 V or 3.3 V operating condition selected for the design. Place required bulk and high-frequency decoupling capacitors at the corresponding supply pins, with the shortest possible current loops and an unobstructed return path. The ADC reference and auxiliary supply pins must receive the values and filtering required by the datasheet. Validate startup sequencing, voltage tolerance, and measured noise because marginal reference supply can affect meter accuracy even when the main digital rail is within specification.

Do not treat the MSP430F6723A and MSP430F6724IPZR candidates as automatic drop-in devices. Their family relationship supports close functional evaluation, but package drawings, terminal assignments, ADC channels, memory configuration, and peripheral multiplexing must be checked against the manufacturer documentation. Preserve the original MSP430F6723IPN footprint only after a complete schematic and firmware review. For production, verify the exact orderable suffix, pin count, package body size, and programming configuration.

Two 24-bit sigma-delta ADCs do not make the device suitable for arbitrary high-speed waveform acquisition. Confirm input bandwidth, sample rate, digital filter response, latency, and acquisition time for each analog channel. Likewise, the RTC, LCD, timers, DMA, and four serial modules share a finite peripheral-pin set. Build the peripheral-allocation matrix early so display segments, communications, debug functions, analog inputs, and timer outputs do not conflict.

合規資訊

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

The available manufacturer and distributor summaries do not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Use the current TI environmental-compliance information and material declaration for procurement decisions.

相關搜尋

MSP430F6723IPN datasheet MSP430F6723IPN datasheet pdf MSP430F6723IPN pinout MSP430F6723IPN footprint Texas Instruments MSP430F6723IPN MSP430F6723IPN price MSP430F6723IPN stock MSP430F6723IPN replacement MSP430F6723IPN equivalent MSP430F6723IPN vs MSP430F6723AIPN MSP430F6723IPN smart meter MSP430F6723IPN single phase metering MSP430F6723IPN LQFP 80 MSP430F6723IPN application circuit

相關元件與詞彙

Texas Instruments MSP430F6723IPN MSP430F6723 MSP430F6723A MSP430F6723AIPN MSP430F6724IPZR MSP430F5521IPN MSP430F5529IPNR MSP430 CPUXV2 16-bit RISC mixed-signal microcontroller metering SoC single-phase smart meter sigma-delta ADC 24-bit ADC 10-bit ADC real-time clock RTC alarm LCD driver eUSCI_A eUSCI_B DMA hardware multiplier 16-bit timer LQFP-80
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情