OPA683ID - 1.44GHz Current-Feedback Amplifier | Texas Instruments
N.º da peça: OPA683ID ✓ AtivoOPA683ID Visão geral
A current-feedback operational amplifier is a voltage-feedback amplifier subclass that uses feedback-network current, rather than differential input voltage alone, to establish closed-loop gain. Current-feedback amplifiers sit within the broader operational-amplifier and analog-signal-processing hierarchies. Their high bandwidth and slew capability make them useful in video, communications, instrumentation, and data-conversion interfaces where a conventional general-purpose amplifier may not provide sufficient operating speed.
The OPA683ID combines its 1.44 GHz bandwidth with a low-power design and a dedicated disable function. The disable control allows the amplifier to enter a low-power state when the associated signal path is not required, which can help reduce system power consumption. Its single-amplifier configuration simplifies designs that need one high-speed analog channel rather than a multi-amplifier package. The 8-pin SOIC (D) package also supports conventional surface-mount PCB assembly.
Unlike a general-purpose voltage-feedback amplifier optimized around nearly constant gain-bandwidth behavior, the OPA683ID uses current-feedback architecture. The exact closed-loop gain, output amplitude, output impedance, load, and feedback-resistor selection must therefore be evaluated together rather than treated as an independent gain-bandwidth calculation. The manufacturer datasheet remains the controlling document for these relationships and for the minimum recommended feedback resistance.
Typical uses include video-signal conditioning, communications infrastructure, high-speed instrumentation, test and measurement equipment, and interface circuitry associated with high-speed converters. The amplifier can also be used where its disable function supports controlled power management in intermittently active signal chains. External signal conditioning may still be required when source impedance, cable capacitance, or output loading exceed the recommended operating conditions.
PCB implementation requires a low-inductance ground reference, short feedback traces, and careful separation between input and output paths. Place the feedback components close to the device, terminate unused inputs and outputs appropriately, and confirm stability with the actual source and load impedances. Decoupling capacitors should be positioned directly beside the supply pins according to the manufacturer layout guidance.
This page combines package, bandwidth, temperature, lifecycle, sourcing, replacement, and design considerations into a compact engineering reference. It also distinguishes verified drop-in alternatives from parts that are merely similar amplifiers, helping designers preserve package compatibility, pin behavior, and the intended current-feedback performance before approving a substitution.
Alternativas drop-in para OPA683ID — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
OPA687ID
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
OPA683ID Classificações máximas e características elétricas
| Amplifier Type | Current-feedback operational amplifier |
| Number of Circuits | 1 circuit |
| Gain-Bandwidth Product | 1.44 GHz |
| Disable Function | Yes |
| Faixa de temperatura de operação | -40°C to +85°C |
| Encapsulamento | 8-pin SOIC (D), 3.90 mm body width |
| Tipo de montagem | Surface mount |
| Status RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
Guia de Configuração de Pinos do OPA683ID 8-pin soic (d), 3.90 mm body width
Configuração de pinos para OPA683ID (pacote 8-pin soic (d), 3.90 mm body width). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.
Nenhum dado detalhado de pinagem disponível para OPA683ID.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
OPA683ID é adequado para 6 aplicaçãos: Wideband Video Signal Conditioning, Communications Interface Amplification, High-Speed Instrumentation Signal Paths, Test and Measurement Equipment, Data Converter Interface, Portable Battery-Powered Analog Equipment.
Wideband Video Signal Conditioning
The OPA683ID fits video-conditioning paths that require a 1.44 GHz current-feedback amplifier in an 8-pin SOIC package. It can amplify or level-shift video signals when the selected feedback network supports the intended closed-loop gain and the source and load impedances remain compatible with the manufacturer's stability guidance. The disable function provides a practical way to reduce power demand when a video channel is inactive. Keep the feedback resistor close to the amplifier, use a low-inductance ground plane, and maintain short traces to minimize added distortion and instability.
Recomendado
Communications Interface Amplification
OPA683ID is suitable for communications interface amplification where a 1.44 GHz bandwidth and current-feedback architecture are needed to process moderate-frequency signals through short PCB paths. Its very-low-power design is useful in portable or intermittently active communication equipment, while the disable function allows the amplifier to be shut down when the associated RF or baseband path is inactive. The exact signal amplitude and impedance environment must be checked against the datasheet, particularly for cable loading, source impedance, output drive, and stable feedback resistance.
Recomendado
High-Speed Instrumentation Signal Paths
The OPA683ID can serve as a wideband instrumentation amplifier stage when the measurement bandwidth requires the device's 1.44 GHz gain-bandwidth product. It is especially relevant where low power and a shutdown function are useful for portable test equipment. Front-end attenuation, gain, input protection, and sensor drive requirements must be designed around the amplifier's input range, output swing, and current capability. Use short, shielded signal routes where appropriate and validate stability with the complete sensor, cable, and termination network rather than an ideal source model.
Recomendado
Test and Measurement Equipment
OPA683ID is appropriate for compact test and measurement equipment that needs a fast, low-power signal-conditioning channel. Its 1.44 GHz bandwidth can accommodate high-bandwidth probes and transient signals, while the disable function can reduce consumption when a test channel is idle. A practical implementation should include controlled input termination, short feedback paths, and local supply bypassing to preserve measurement integrity. Confirm the required output amplitude, load, source impedance, and gain against the manufacturer data before defining the surrounding attenuator and driver circuitry.
Recomendado
Data Converter Interface
The OPA683ID can be used in interface paths around high-speed data converters when the converter requires an amplifier with wide bandwidth and low power. Its 1.44 GHz gain-bandwidth product provides bandwidth for edge-rate requirements, while its current-feedback architecture can be advantageous with the correct feedback impedance. The amplifier should be placed close to the converter or isolation resistor, and its inputs and outputs should be routed away from noisy digital and clock paths. Use the manufacturer's recommended decoupling and feedback arrangements to avoid converter-edge ringing.
Recomendado
Portable Battery-Powered Analog Equipment
OPA683ID is suitable for portable battery-powered analog equipment because Texas Instruments describes it as a very-low-power current-feedback amplifier and includes an active disable function. The 1.44 GHz bandwidth supports wideband processing without requiring a larger high-speed amplifier package, while shutdown can reduce demand when the instrument is between measurements. Power architecture should account for the exact quiescent current, active current, and disable leakage from the manufacturer data. The complete signal path must also remain stable over the battery-voltage range and across source and load variations.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para OPA683ID — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | OPA687ID |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC (D) | 8-pin SOIC (D) |
| Amplifier Architecture | Current-feedback | Current-feedback |
| Number of Circuits | 1 circuit | 1 circuit |
| Gain-Bandwidth Product | 1.44 GHz | Approximately 1.5 GHz |
| Disable Function | Yes | Yes |
| Special Features | Very-low-power wideband amplifier with disable | Wideband current-feedback amplifier with disable |
Principais diferenciais
- Closely matched same-family bandwidth (vs OPA687ID)
- Integrated power-state control (vs OPA687ID)
- Purpose-built very-low-power wideband positioning (vs OPA687ID)
Notas de projeto
Place the feedback resistor and its return path directly beside the OPA683ID pins, and keep the input and output routing short. Use a continuous ground plane with no split beneath the device, and place supply-bypass capacitors at the closest available supply and ground pins. High-speed current-feedback amplifiers can amplify trace inductance, parasitic capacitance, and impedance discontinuities, so the physical layout should be treated as part of the feedback network.
Validate stability with the actual source impedance, transmission-line loading, output load, and selected feedback resistor rather than assuming ideal sources. Current-feedback amplifiers do not follow voltage-feedback bandwidth rules, and changing source impedance can alter frequency response. If ringing appears, verify grounding, component placement, feedback-loop length, output isolation, and termination before increasing the feedback resistance.
Do not infer disable polarity or inactive output behavior from the product description. Read the logic thresholds and timing information in the manufacturer data, and ensure external circuitry cannot back-drive the disabled output. Also check maximum input and output voltages under every operating state. The -40°C to +85°C rating identifies the operating temperature range, but it does not by itself guarantee performance across every combination of supply, load, and source impedance.
Informações de conformidade
The verified manufacturer and distributor information does not state the requested compliance statuses. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations for the exact orderable MPN and current manufacturing status.