PCM1755DBQR - 24-Bit Stereo Audio DAC | Texas Instruments
N.º da peça: PCM1755DBQR ✓ AtivoPCM1755DBQR Visão geral
An audio DAC converts digital PCM audio streams into left and right analog voltage signals suitable for headphone, line-level, or power-amplifier inputs. The PCM1755 belongs to the delta-sigma DAC hierarchy, combining a multi-level quantization architecture, fourth-order noise shaping, digital oversampling, and an analog output stage. These functions place it between digital audio processors and downstream analog audio amplification.
Key performance features include 24-bit data resolution, 106 dB dynamic range, 106 dB typical signal-to-noise ratio, and 0.002% typical total harmonic distortion plus noise. The converter supports 4× or 8× oversampling and provides 50 dB stop-band attenuation. A typical full-scale analog output of 4 VPP provides useful headroom for balanced or single-ended audio circuitry.
The PCM1755 uses TI's enhanced multilevel delta-sigma architecture with eight-level amplitude quantization and fourth-order noise shaping. This architecture is intended to improve clock-jitter tolerance while retaining high-resolution performance. Configuration is available through hardware control or a three-wire serial control port that supports register writes, allowing the host processor to select operating modes and implement programmable functions.
Typical applications include high-resolution audio players, network audio equipment, home-theater audio systems, digital mixing consoles, active speakers, and professional audio interfaces. Its 106 dB SNR supports low-noise reconstruction, while the 24-bit interface accommodates modern digital audio pipelines. The I2S-compatible interface also simplifies connection to audio DSPs and digital audio engines.
Layout should prioritize short, symmetric analog output paths and clean return currents between the DAC, output filtering network, and following amplifier. Power and ground planes should be decoupled close to the device, and analog signal routing should avoid digital clock and serial-control traces. The analog output architecture and supported single-ended interface determine the external filtering and gain-stage requirements.
This page combines the manufacturer's device specifications, package and ordering details, drop-in replacement evidence, comparison parameters, and practical PCB guidance. It is intended to help engineers evaluate the PCM1755DBQR for audio DAC boards, digital audio platforms, and retrofit projects where 24-bit conversion, 106 dB SNR, and a 16-pin SSOP footprint are central design requirements.
Alternativas drop-in para PCM1755DBQR — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
PCM1754DBQG4
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PCM1755DBQ
✅ Drop-InConsulte o preço
Ver ficha técnica →PCM1755DBQG4
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PCM1755DBQR Classificações máximas e características elétricas
| Device Type | Stereo audio digital-to-analog converter (DAC) |
| Data Resolution | 24 bit |
| Maximum Listed Sampling Rate | 200 kHz |
| Digital Audio Interface | I2S |
| Dynamic Range at 5 V | 106 dB |
| Signal-to-Noise Ratio at 5 V | 106 dB typical |
| Total Harmonic Distortion Plus Noise at 5 V | 0.002% typical |
| Full-Scale Output at 5 V | 4 VPP typical |
| Digital Filter Oversampling | 4× or 8× |
| Stop-Band Attenuation | -50 dB |
| Control Interface | Hardware control or 3-wire serial register-write control |
| Converter Architecture | Enhanced multilevel delta-sigma with 4th-order noise shaping and 8-level amplitude quantization |
| Tensão de alimentação | 5 V for stated analog-performance conditions |
| Encapsulamento | 16-pin SSOP (DBQ), 0.154 in × 3.90 mm |
| Tipo de montagem | Surface mount |
| Packaging | Tape and reel |
| Status RoHS | RoHS3 compliant |
| Lead-Free Status | Lead free |
Guia de Configuração de Pinos do PCM1755DBQR 16-pin ssop (dbq), 0.154 in × 3.90 mm
Configuração de pinos para PCM1755DBQR (pacote 16-pin ssop (dbq), 0.154 in × 3.90 mm). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.
Nenhum dado detalhado de pinagem disponível para PCM1755DBQR.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
PCM1755DBQR é adequado para 6 aplicaçãos: High-Resolution Network Audio Player, Professional Audio Interface, Digital Mixing Console Output, Active Speaker USB Audio Interface, Home Theater Stereo Output, Digital Audio Recorder Playback Monitor.
High-Resolution Network Audio Player
The PCM1755DBQR fits a network audio player that accepts 24-bit digital streams and requires a clean stereo analog stage. Its 106 dB typical SNR and 0.002% typical THD+N at a 5 V supply establish a high-performance conversion baseline, while the I2S interface connects to an audio DSP or network-audio SoC. The device accepts up to the listed 200 kHz sampling rate and offers 4× or 8× oversampling. A practical implementation places the DAC close to the output connector, uses short left and right analog routes, and preserves a quiet ground return to the line-level amplifier. The main trade-off is that a linear analog reconstruction and output-filter network remain necessary to translate the converter’s current or voltage-domain outputs into the exact gain and impedance required by the following stage.
Recomendado
Professional Audio Interface
The PCM1755DBQR is appropriate for a professional stereo audio interface that reconstructs high-resolution playback channels for monitoring and recording systems. Its 24-bit data path, 106 dB dynamic range, and 106 dB typical SNR provide headroom for the converter stage, while the three-wire serial control port allows a host controller to configure programmable functions. The I2S connection can link to an audio DSP that handles routing, sample-rate conversion, and clock generation. Use short analog traces and independent left and right filtering to minimize channel skew and crosstalk. Because system noise also originates in references, regulators, clock sources, and the analog output amplifier, evaluate the complete signal chain rather than treating the DAC’s SNR as the only system noise limit.
Recomendado
Digital Mixing Console Output
The PCM1755DBQR can serve as the final stereo monitoring DAC in a digital mixing console because it combines a 24-bit conversion path with software-controlled operating functions. The 106 dB typical SNR and 0.002% typical THD+N are useful when preserving quiet program material through the console’s output stage. The converter can be driven from an I2S-enabled DSP, with its three-wire serial interface providing configuration and control. Keep the digital bus and clock away from the analog outputs, provide local supply bypassing, and route both channels with matched geometry. Designers should verify the required digital filter mode, de-emphasis behavior, output topology, and master-clock arrangement against the manufacturer datasheet before finalizing the console output board.
Recomendado
Active Speaker USB Audio Interface
The PCM1755DBQR is well suited to the stereo playback section of a USB audio interface feeding powered speakers or headphones. Its I2S input accepts digital audio from a USB controller, while the 106 dB dynamic range and 0.002% typical THD+N support quiet reconstruction of high-resolution recordings. The 16-pin SSOP package keeps the converter compact, and the listed maximum sampling rate of 200 kHz accommodates high-rate source formats. A practical board should isolate the DAC’s analog path from USB and clock routing, use a continuous ground plane, and place output-network components close to their associated pins. The downstream amplifier and headphone driver still set the final output noise, output impedance, and channel-balance performance.
Recomendado
Home Theater Stereo Output
The PCM1755DBQR can provide the stereo analog output for a home-theater processor, television, or compact media appliance. The 24-bit interface and 106 dB typical SNR support accurate reconstruction of compressed and lossless source material, while the converter’s 4× or 8× oversampling options provide digital-filter flexibility. Connect the I2S data, clock, and channel-selection signals from the system audio processor, then use a low-noise analog filter before the line-level amplifier. Short output routing and quiet reference connections help preserve the converter’s performance. If the design requires additional surround channels, a multi-channel codec may be more integration-efficient than adding one stereo PCM1755DBQR for each pair of channels.
Recomendado
Digital Audio Recorder Playback Monitor
The PCM1755DBQR fits the playback-monitoring DAC in a digital recorder because it delivers 24-bit stereo reconstruction with 106 dB typical SNR and low 0.002% typical THD+N. The I2S interface allows direct connection to the recorder’s digital audio engine, and hardware or three-wire serial control supports integration with different system architectures. For monitoring applications, maintain matched analog paths for the two channels and keep the DAC reference and supply return currents away from noisy digital and power-converter regions. Validate the required output level, filter mode, and clock relationship against the manufacturer application circuit. This device addresses conversion quality, while the monitor amplifier, headphone stage, and mechanical isolation determine much of the final perceived performance.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PCM1755DBQR — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PCM1754DBQG4 | PCM1755DBQ | PCM1755DBQG4 |
|---|---|---|---|---|
| Package | 16-pin SSOP (DBQ) | 16-pin SSOP (DBQ) | 16-pin SSOP (DBQ) | 16-pin SSOP (DBQ) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Device Type | Stereo audio DAC | Stereo audio DAC | Stereo audio DAC | Stereo audio DAC |
| Data Resolution | 24 bit | 24 bit | 24 bit | 24 bit |
Principais diferenciais
- Software-control capability through a three-wire serial register-write interface (vs PCM1754DBQG4)
- High-resolution conversion with a 106 dB dynamic range (vs PCM1754DBQG4)
- Flexible digital filtering and broad high-rate support (vs PCM1754DBQG4)
Notas de projeto
Keep the I2S data and clock routes away from the left and right analog outputs, and use symmetrical geometry for the two channels. Place output-filter components close to the relevant DAC pins, maintain a continuous ground plane beneath the analog section, and return digital and analog currents without sharing narrow paths. This reduces coupling from the 200 kHz-class digital activity into the reconstructed audio and helps preserve channel balance.
Use the manufacturer application circuit as the basis for supply and reference decoupling, then place the required capacitors at the device pins with short, low-inductance connections. The quoted 106 dB SNR, 0.002% THD+N, and 4 VPP output are specified at a 5 V supply, so verify that the power topology provides a stable operating point under the intended load. Pay particular attention to reference noise because it can directly establish the system’s audible noise floor.
Treat the I2S serial clock as a high-speed digital signal even though the audio payload is low bandwidth. Maintain a continuous return path beneath the bus, avoid stubs, and keep clock routing away from the analog output nodes. Confirm the master-clock relationship, bit-clock polarity, data format, and channel selection against the manufacturer configuration tables before releasing the PCB layout.
Informações de conformidade
The PCM1755DBQR listing identifies RoHS3 compliance and lead-free construction. No additional REACH, AEC-Q100, halogen-free, or conflict-minerals declarations are stated.