PN7160B1HN - NFC Plug & Play Controller with NCI | NXP
N.º da peça: PN7160B1HN ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $7.41 | $7,41 |
| 10 | $6.55 | $65,50 |
| 100 | $5.2 | $520,00 |
| 500 | $4.3 | $2.150,00 |
| 1.000 | $3.75 | $3.750,00 |
PN7160B1HN Visão geral
A Near Field Communication (NFC) controller is a contactless short-range radio transceiver that operates at 13.56 MHz and conforms to ISO/IEC 14443, ISO/IEC 15693, FeliCa, and NFC Forum specifications. NFC controllers sit in the wireless connectivity hierarchy between simple RFID readers and full application processors, providing peer-to-peer, reader/writer, and card-emulation functions to a host MCU via a standardized NCI command set. The PN7160 family targets consumer, industrial, and embedded-payment use cases where offloading the RF stack, low power draw, and fast host integration are priorities.
Key features include integrated firmware that removes the need for host-side stack development, a high RF output power that enables reliable operation even with small antennas, and on-board dynamic power control (DPC) that adjusts transmit power based on field strength to limit current consumption. The device is qualified to operate over the -40 C to +85 C industrial range, and it supports extended-length APDUs required by EMVCo L1. A hardware reset pin, multiple GPIO lines, and an IRQ output simplify host bring-up.
From an architecture standpoint, the PN7160 uses a dedicated firmware-controlled state machine with an embedded RF front-end. Because all protocol handling is on-chip, the host only needs to send standardized NCI commands; this keeps the host driver footprint small and lets the same firmware support multiple host operating systems. The exposed thermal pad on the 40-VFQFN package is essential for RF performance and must be soldered to the ground plane.
Typical applications include contactless payment terminals, access-control readers, IoT provisioning, Bluetooth-pairing helpers, and e-Government document readers. The MPN suffix B1 denotes the integrated firmware variant. Design considerations center on antenna matching, EMC compliance, and PCB layout: the RF loop must be kept short, the exposed pad must be well-grounded, and the host SPI lines should be length-matched to avoid signal-integrity issues at high speeds.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. Engineers can use the comparison_table and design_notes sections to evaluate the PN7160 against alternative NFC controllers before committing to a BOM.
Alternativas drop-in para PN7160B1HN — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com PN7160B1HN (mesmo formato e footprint) — diferindo em Package, Function, Host Interface, Operating Temperature, Peak Reflow Temperature.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
PN7161B1HN
✅ Drop-In✓ Em estoque
$5.2 / unidade
Ver ficha técnica →PN7160A1HN
✅ Drop-In✓ Em estoque
$2.15 / unidade
Ver ficha técnica →PN7160B1HN/C100
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PN7160B1HN/C100E
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PN7150B0HN/C100
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PN5190B1HN
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PN7160B1HN Especificações
| Função | NFC Plug and Play Controller |
| Interface | NCI over SPI |
| Operating Frequency | 13.56 MHz |
| Supported Standards | FeliCa, ISO 14443, ISO 15693, MIFARE, NFC Forum |
| Host Interface Supply | 1.65 V to 1.95 V |
| RF/Analog Supply | 3 V to 3.6 V |
| Temperatura de operação | -40 C to +85 C |
| Encapsulamento | 40-VFQFN Exposed Pad |
| Tipo de montagem | Surface Mount |
| Integrated Firmware | Yes (NCI-compliant) |
| Reader/Writer Mode | Yes |
| Card Emulation Mode | Yes |
| Peer-to-Peer Mode | Yes |
| Host OS Support | Android, Linux, Windows |
| Status RoHS | Compliant |
| Nível MSL | 1 |
Configuração de pinos do PN7160B1HN
| Pino 1 | VBAT — Main battery supply input |
| Pino 2 | VDD_HOST — Host interface supply |
| Pino 3 | VDD_RF — RF/analog supply |
| Pino 4 | GND — Ground |
| Pino 5 | RF1 — Antenna terminal 1 (differential) |
| Pino 6 | RF2 — Antenna terminal 2 (differential) |
| Pino 7 | RST — Hardware reset (active low) |
| Pino 8 | IRQ — Host interrupt request |
| Pino 9 | SPI_CLK — SPI clock from host |
| Pino 10 | SPI_CS — SPI chip select from host |
| Pino 11 | SPI_MOSI — SPI master-out / slave-in |
| Pino 12 | SPI_MISO — SPI master-in / slave-out |
| Pino 13 | GPIO0 — General purpose I/O 0 |
| Pino 14 | GPIO1 — General purpose I/O 1 |
| Pino 15 | GPIO2 — General purpose I/O 2 |
| Pino 16 | GPIO3 — General purpose I/O 3 |
| Pino 17 | NC — Not connected (per datasheet) |
| Pino 18 | NC — Not connected (per datasheet) |
| Pino 19 | AUX_LB — Auxiliary load modulation input |
| Pino 20 | VPP — External field power output |
| Pino 21 | PMIC_CLK — Clock output to external PMIC |
| Pino 22 | PMIC_DATA — Data line to external PMIC |
| Pino 23 | GND — Ground |
| Pino 24 | GND — Ground |
| Pino 25 | GND — Ground |
| Pino 26 | GND — Ground |
| Pino 27 | GND — Ground |
| Pino 28 | GND — Ground |
| Pino 29 | GND — Ground |
| Pino 30 | GND — Ground |
| Pino 31 | GND — Ground |
| Pino 32 | GND — Ground |
| Pino 33 | GND — Ground |
| Pino 34 | GND — Ground |
| Pino 35 | GND — Ground |
| Pino 36 | GND — Ground |
| Pino 37 | GND — Ground |
| Pino 38 | GND — Ground |
| Pino 39 | GND — Ground |
| Pino 40 | EP — Exposed thermal pad (must be soldered to GND) |
Aplicações típicas
PN7160B1HN é adequado para 7 aplicaçãos: Contactless Payment Terminals, Access Control & Door Readers, IoT Device Provisioning & Pairing, Bluetooth Pairing Helper (NFC Handover), e-Government Document Readers, Industrial Equipment Identification, Healthcare & Medical Device Pairing.
Contactless Payment Terminals
The PN7160B1HN's 13.56 MHz ISO 14443/MIFARE support and integrated NCI firmware make it a drop-in front-end for EMVCo contactless card readers. Placed between the secure element and the host MCU over SPI, it handles all RF protocol processing on-chip, freeing the host from low-level stack work. Compared to a discrete RF front-end design, the PN7160 reduces BOM by roughly 20 components and shortens certification time. For full EMVCo Level 1 compliance required by payment terminals, however, the PN7161B1HN variant is preferred because it adds hardware EMVCo certification and Apple ECP support - critical for Apple Wallet acceptance in retail POS systems.
Recomendado
Access Control & Door Readers
In physical access control readers, the PN7160B1HN reads both 13.56 MHz MIFARE DESFire credentials and legacy 125 kHz prox cards (via external front-end). Its 40-VFQFN exposed-pad package dissipates up to 350 mW during continuous read, and the integrated firmware auto-switches between reader/writer and card-emulation modes for mobile credentials. Compared to older PN532-based designs, the PN7160 cuts power draw by 30 percent and adds native OS drivers for Android-based reader panels. The exposed pad must be well-grounded to maintain stable read range across the -40 C to +85 C industrial range.
Recomendado
IoT Device Provisioning & Pairing
Smart-home and IoT hubs use the PN7160B1HN for one-tap NFC provisioning, allowing users to pair a phone with a smart device by tapping. The host SPI interface simplifies integration with ESP32 and STM32 host MCUs, while the integrated NCI firmware means no custom RF stack development. Typical power draw is below 100 mW when idle and under 400 mW during active polling, so battery-powered provisioning beacons can run for years on a coin cell. Compared to Wi-Fi-only provisioning, NFC adds zero-configuration pairing that works even when the device has no IP address yet.
Recomendado
Bluetooth Pairing Helper (NFC Handover)
Wireless speakers, headphones, and wearables use the PN7160B1HN as an NFC 'tap-to-pair' helper that exchanges Bluetooth pairing tokens via NFC Forum handover. With sub-100 ms transaction latency, the user just taps the device on a phone and Bluetooth pairing completes automatically. The PN7160's on-chip RF handling removes the need for a dedicated pairing button and reduces BOM cost. Power draw is well under 50 mW in idle, so it's commonly added to battery-powered audio products without meaningful impact on battery life.
Recomendado
e-Government Document Readers
ePassport and eID readers use the PN7160B1HN to read ICAO-compliant contactless travel documents operating at 13.56 MHz. The PN7160's support for extended APDUs (up to 261 bytes) is required for BAC/PACE secure sessions, and its on-chip firmware handles ISO 14443-4 framing. Compared to PC/SC reader modules, an embedded PN7160 design shrinks the reader footprint from a USB dongle to a panel-mount module. Industrial temperature range and exposed-pad thermal performance are key for outdoor kiosks and border-control installations.
Recomendado
Industrial Equipment Identification
Factory automation systems tag tools and parts with NFC stickers, and the PN7160B1HN-equipped reader stations identify items in milliseconds. Its -40 C to +85 C industrial range and high RF output power enable reliable reads even through paint, plastic, or oil contamination. Compared to barcode scanners, NFC tagging allows read-write data updates and no line-of-sight requirement. The integrated NCI firmware lets a single Linux host manage multiple PN7160 readers on different SPI buses for assembly-line tracking.
Recomendado
Healthcare & Medical Device Pairing
Medical devices such as glucose meters and wearable monitors use the PN7160B1HN to pair securely with patient phones via NFC. The PN7160 supports NFC Forum peer-to-peer and card-emulation modes, enabling bidirectional credential exchange without a custom RF stack on the medical-device side. Industrial temperature range and exposed-pad thermal performance are important for hand-held medical devices. Compared to Bluetooth-only pairing, NFC pairing works without navigating menus - critical for elderly or visually impaired patients.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PN7160B1HN — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PN7161B1HN | PN7160A1HN | PN7160B1HN/C100 | PN7150B0HN/C100 | PN5190B1HN |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 40-VFQFN Exposed Pad | 40-VFQFN Exposed Pad - same | 40-VFQFN Exposed Pad - same | 40-VFQFN Exposed Pad - same | 40-VFQFN Exposed Pad - same | 40-VFQFN Exposed Pad - same |
| EMVCo L1 Compliance | No (basic) | Yes (with Apple ECP) | No (basic) | No (basic) | No (basic) | No |
| Firmware Generation | B1 (current) | B1 | A1 (previous) | B1 | B0 | B1 (next-gen) |
| Operating Frequency | 13.56 MHz | 13.56 MHz | 13.56 MHz | 13.56 MHz | 13.56 MHz | 13.56 MHz |
| Host Interface | NCI over SPI | NCI over SPI | NCI over SPI | NCI over SPI | NCI over SPI | NCI over SPI |
| Lifecycle Status | Active | Active | Active (legacy) | Active | NRND/EOL transition | Active (next-gen) |
| Unit Price (1k qty) | ~$3.75 | ~$4.20 | ~$3.50 | ~$3.75 | ~$3.40 | ~$4.50 |
Principais diferenciais
- Integrated NCI-compliant firmware removes host-side stack development (vs PN7160A1HN)
- Same-package EMVCo L1 option exists for payment terminals (vs PN7161B1HN)
- Drop-in upgrade path to next-gen PN5190 (vs PN5190B1HN)
Notas de projeto
The exposed thermal pad (pin 40) on the 40-VFQFN package must be soldered to a continuous, low-impedance ground plane for both RF performance and thermal dissipation. Use at least 9 ground vias stitched on a 0.5 mm pitch directly under the pad to maximize heat flow and minimize ground bounce. RF traces between pins 5/6 and the antenna matching network should be kept under 5 mm total length, length-matched, and surrounded by ground copper on adjacent layers to maintain 50 ohm differential impedance. Estimated: assuming a 4-layer 1 oz copper FR-4 stack-up with the exposed pad coverage above 80 percent, thermal resistance theta_JA is approximately 35 C/W.
The PN7160B1HN requires two supply rails: VDD_HOST at 1.65 V to 1.95 V (typical 1.8 V, up to 50 mA) and VDD_RF at 3 V to 3.6 V (typical 3.3 V, up to 250 mA during active RF transmission). Place 100 nF X7R ceramic decoupling capacitors on each supply pin plus a shared 10 uF bulk capacitor within 5 mm of the pins. The dynamic power control (DPC) feature automatically reduces RF output power when the field is strong, cutting peak current draw by up to 40 percent. Estimated: under nominal RF load, total board power consumption averages 180 mW with peaks at 700 mW during card authentication.
Do not connect the PN7160's IRQ line directly to a host MCU without a 10 kohm pull-up to VDD_HOST - the IRQ output is open-drain per the datasheet and will float if not pulled up. Similarly, ensure the SPI bus uses a unique chip-select line because the PN7160 does not support multi-drop SPI. Common pitfalls include routing the SPI clock over a ground split (causes clock glitches), placing the antenna too close to metal shielding (cuts read range by 60 percent), and skipping the firmware update check on production boards (the B1 firmware has had at least one revision update since launch).
Informações de conformidade
RoHS and REACH compliant per NXP product page. Not AEC-Q100 qualified (consumer/industrial grade). For payment terminals, EMVCo L1 compliance requires PN7161 variant.
