SN74LS242D - Quad Bus Transceiver | Texas Instruments | SOIC-14
N.º da peça: SN74LS242D ✓ AtivoSN74LS242D Visão geral
A bus transceiver is a logic-interface device that combines driver and receiver functions in one package. In the broader semiconductor hierarchy, the SN74LS242D belongs to the logic IC family, specifically the 74LS bus-buffer and transceiver category. Its four sections can help reduce the number of discrete buffers required when a system exchanges data between incompatible bus directions or separates a source from a receiving device.
The principal device-level facts are its quadruple-transceiver configuration, 14-pin SOIC package, and 0°C-to-70°C operating range. Pin functions, supply voltage, propagation delay, output-current capability, input and output thresholds, and enable-control logic should be confirmed in the Texas Instruments SN74LS242 datasheet before schematic capture or timing analysis. The SOIC form factor supports conventional through-hole PCB assembly and automated insertion.
As a member of the SN74LS logic family, the device is intended for digital bus-interface applications rather than precision analog, high-speed memory, or RF signal conditioning. The four channels provide a practical way to implement buffered, direction-controlled interconnects in equipment built with TTL-compatible logic. PCB designers should preserve the manufacturer's connection and decoupling recommendations to avoid introducing bus-contention or signal-integrity problems.
Typical uses include general-purpose digital bus isolation, data acquisition, industrial control interfaces, instrumentation, computer peripherals, and test-equipment signal routing. In each case, the transceiver's direction-control and enable behavior must be coordinated with the logic driving the bus so that drivers are never simultaneously commanded in opposite directions.
The principal design consideration is bus contention. Before enabling either side of a channel, confirm that all external devices connected to that side are disabled or high-impedance. Keep data and direction traces short, provide a stable supply reference, and place the required bypassing capacitance close to the device. The 0°C-to-70°C rating makes this part appropriate for commercial-temperature equipment rather than extended industrial or automotive environments.
This page organizes the SN74LS242D's function, package, environmental limits, sourcing information, replacement constraints, and application guidance. It also distinguishes verified ordering information from engineering assumptions, helping designers determine whether the 14-pin SOIC device fits an existing board and which signal-integrity checks are required before deployment.
Alternativas drop-in para SN74LS242D — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Nenhuma alternativa drop-in disponível para este produto.
Solicitar alternativasSN74LS242D Classificações máximas e características elétricas
| Device Type | Quad bus transceiver |
| Number of Transceiver Elements | 4 elements |
| Logic Family | 74LS |
| Encapsulamento | 14-pin SOIC |
| Tipo de montagem | Through-hole SOIC |
| Faixa de temperatura de operação | 0°C to 70°C |
Guia de Configuração de Pinos do SN74LS242D 14-pin soic
Configuração de pinos para SN74LS242D (pacote 14-pin soic). Este CI digital inclui GPIO, interfaces de comunicação (UART, SPI, I2C) e pinos de alimentação. Consulte o datasheet do fabricante para funções alternativas dos pinos e opções de configuração. Essencial para projeto de sistemas embarcados e layout de PCB.
Nenhum dado detalhado de pinagem disponível para SN74LS242D.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
SN74LS242D é adequado para 6 aplicaçãos: General-Purpose Digital Bus Buffering, Data Acquisition Interface, Industrial Control Interface, Test and Measurement Equipment, Computer Peripheral Interconnect, Instrumentation Signal Routing.
General-Purpose Digital Bus Buffering
The SN74LS242D fits general-purpose digital bus buffering because it combines four transceiver sections in one 14-pin SOIC package. Each section can support a direction-controlled interface between a bus source and a bus receiver, reducing the number of separate buffer packages required on a board. The confirmed commercial temperature range of 0°C to 70°C suits room-temperature control and instrumentation equipment. During implementation, verify the enable and direction truth table in the manufacturer datasheet, prevent simultaneous opposing drive from connected devices, and route the bus so that disabled outputs do not contend with active logic.
Recomendado
Data Acquisition Interface
The SN74LS242D can be used at the interface between a data-acquisition system and external digital equipment when the system requires four controlled transceiver channels rather than four separate devices. Its 14-pin SOIC format keeps the circuit compact, while the quad organization provides a consistent way to isolate or buffer two sides of a digital connection. Because the device is a logic transceiver rather than an analog front end, it should remain behind the converter that represents each measurement. Confirm the direction controls and signal thresholds against the Texas Instruments datasheet, and design the analog section to prevent bus activity from disturbing sensitive conversion circuitry.
Recomendado
Industrial Control Interface
The SN74LS242D is applicable to commercial-temperature industrial control equipment that uses TTL-compatible logic and requires four direction-controlled bus paths. The quad arrangement can connect a controller to external modules while keeping driver and receiver functions in one standardized package. Its stated 0°C-to-70°C range suits controlled indoor installations, but it does not by itself establish suitability for extended industrial temperatures. Designers should include system-level bus isolation where required, control enable states during reset, and verify that all connected outputs are high impedance before enabling a driver. PCB placement should minimize loop area and preserve a common ground reference between the transceiver and communicating devices.
Recomendado
Test and Measurement Equipment
The SN74LS242D can support internal digital routing in test and measurement instruments where four TTL-compatible transceiver sections are needed between test-control logic and external connectors or fixtures. Combining four sections in one 14-pin SOIC can simplify PCB area planning, while the controlled operating range of 0°C to 70°C aligns with laboratory and production-test environments. Engineers should treat the transceiver as a digital route, not as an instrument input or analog buffer. Use the datasheet timing information when establishing setup and hold requirements, avoid reflective stubs on long cable connections, and ensure that connected test equipment remains disabled during mode changes to prevent bus contention.
Recomendado
Computer Peripheral Interconnect
The SN74LS242D is suitable for legacy-style computer peripheral interconnects that use TTL-compatible bidirectional digital buses and require four controlled channels. Its four transceiver sections can support routing between a controller and multiple peripheral-side buses when direction is managed by the host logic. The 14-pin SOIC package is convenient for conventional through-hole board assembly and does not require a fine-pitch surface-mount footprint. The key integration risk is contention at power-up or during reset. Hold the transceiver disabled until every connected device has reached a defined state, and use the manufacturer enable and direction truth table to avoid driving two outputs against each other.
Recomendado
Instrumentation Signal Routing
The SN74LS242D can route digital control and status signals inside instrumentation systems where separate source and destination logic domains must be connected through a direction-controlled transceiver. Its four channels offer a consolidated interface for enable, mode, interlock, or status paths while preserving the familiar 74LS logic family. The device should be used only for compatible digital signals; it is not a substitute for precision analog buffers or isolation amplifiers. Use short, properly referenced traces and follow the datasheet recommendations for bypassing and enable sequencing. Where safety or high-voltage isolation matters, add the required isolation barrier rather than relying on the transceiver package for protection.
Recomendado
Dados de referência de engenharia para SN74LS242D — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto |
|---|---|
| Device Type | Quad bus transceiver |
| Number of Elements | 4 |
| Logic Family | 74LS |
| Package | 14-pin SOIC |
| Brand | Texas Instruments |
| Operating Temperature Range | 0°C to 70°C |
Notas de projeto
Prevent bus contention by keeping every transceiver channel disabled until all devices connected to the bus have reached a defined output state. Two outputs driving opposite logic levels through a low-impedance path can produce excessive current, undefined voltage, and possible component damage. Use the manufacturer's enable and direction truth table, hold the device inactive during reset, and ensure external devices provide a defined disable state before the transceiver becomes active.
Place the transceiver close to the digital interface it serves and keep data and direction traces short enough to limit propagation delay, ringing, and susceptibility to crosstalk. Provide a continuous ground plane and follow the datasheet's supply-bypassing recommendations. Because the SN74LS242D is a 14-pin SOIC, verify the PCB's through-hole pad pattern, pin-one orientation, and component clearance against the actual package drawing before releasing the board layout.
Treat each transceiver channel as a bidirectional logic connection rather than two independent point-to-point links. Direction-control traces should not be allowed to change while the corresponding outputs are actively driving. Check propagation-delay and enable timing from the datasheet against the clocking rate of the connected system, and add termination or series damping only when required by the complete board topology and edge rate.
Informações de conformidade
No compliance declarations were identified in the available product and distributor information. AEC-Q100 is not applicable to this commercial-temperature 74LS logic device.