STM32G431K6U3 - 170MHz Cortex-M4F MCU, 32KB | STMicroelectronics
N.º da peça: STM32G431K6U3 ✓ AtivoSTM32G431K6U3 Visão geral
A general-purpose microcontroller is a programmable semiconductor that executes firmware, controls peripherals, and exchanges data with sensors, actuators, and communications equipment. The STM32G4 family belongs to the hierarchy of embedded microcontroller, 32-bit RISC processor, Arm Cortex-M4F core, and embedded-control semiconductor. STM32G431K6U3 is particularly suited to systems requiring deterministic control, fast analog conversion, and communication functions in a space-constrained design.
Key features include a 170 MHz Arm Cortex-M4F processor with floating-point capability, 32 KB of Flash program memory, 26 I/O pins, and an integrated math accelerator. Its connected peripherals include CANbus, I2C, SPI, UART/USART, and other serial interfaces, while its analog resources include medium-resolution ADCs, operational amplifiers, comparators, and DAC functions. These resources allow a compact controller to supervise power conversion, acquire sensor data, and communicate with external equipment without requiring several separate devices.
The Cortex-M4F architecture uses a 32-bit RISC instruction set and includes single-precision floating-point instructions for control calculations. The STM32G431K6U3 also supports programmable timer resources for motor control, digital power conversion, and periodic signal generation. Brown-out detection and reset, DMA, programmable power and timing behavior, and direct-memory-access peripherals help separate data-transfer tasks from the CPU core.
Typical applications include digital power supplies and motor controllers, where PWM generation, fast analog feedback, and communication interfaces are valuable. The device can also serve in industrial sensor hubs, data-acquisition modules, compact industrial control panels, and communication equipment requiring CANbus, SPI, or UART connectivity. Its 32-pin package reduces board area while preserving a broad selection of general-purpose interfaces.
PCB design should preserve access to every UFQFPN lead, provide a stable local supply and ground distribution, and route analog inputs away from fast switching and high-current paths. Check the manufacturer pin-description and land-pattern tables before assigning signals, and use the recommended decoupling arrangement for reliable operation.
This page combines device specifications, application guidance, package information, and same-package alternatives to support faster engineering evaluation. Because flash capacity and package dimensions can change the most appropriate replacement, verify firmware size, peripheral requirements, and pin assignments before approving any substitution.
Alternativas drop-in para STM32G431K6U3 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com STM32G431K6U3 (mesmo formato e footprint) — diferindo em Package, Math Accelerator, Mounting Type, Core, Flash Memory.
STM32G431K6T6
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
STM32G431K8T6
✅ Drop-In ⚠️ Especificações não verificadasConsulte o preço
Ver ficha técnica →STM32G431K8T3
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
STM32G431KBT6
✅ Drop-In ⚠️ Especificações não verificadasConsulte o preço
Ver ficha técnica →STM32G431K6U3 Classificações máximas e características elétricas
| Product Type | 32-bit Arm Cortex-M4F microcontroller |
| Maximum CPU Frequency | 170 MHz |
| Core Architecture | Arm Cortex-M4F with floating-point instructions |
| Instruction Set Width | 32-bit RISC |
| Program Memory Size | 32 KB Flash |
| Flash Organization | 32K × 8 bits |
| Number of I/O Pins | 26 pins |
| Encapsulamento | 32-pin UFQFPN, 5 mm × 5 mm |
| Tipo de montagem | Surface mount |
| Serial Interfaces | CANbus, I2C, SPI, UART/USART |
| Math Accelerator | Integrated hardware math accelerator |
| Data Transfer | DMA-supported peripherals |
| System Protection | Brown-out detection and reset |
Guia de Configuração de Pinos do STM32G431K6U3 32-pin ufqfpn, 5 mm × 5 mm
Configuração de pinos para STM32G431K6U3 (pacote 32-pin ufqfpn, 5 mm × 5 mm). Este CI digital inclui GPIO, interfaces de comunicação (UART, SPI, I2C) e pinos de alimentação. Consulte o datasheet do fabricante para funções alternativas dos pinos e opções de configuração. Essencial para projeto de sistemas embarcados e layout de PCB.
Nenhum dado detalhado de pinagem disponível para STM32G431K6U3.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
STM32G431K6U3 é adequado para 6 aplicaçãos: Digital Power Converters, BLDC and PMSM Motor Control, Industrial Sensor Hubs, Data Acquisition Modules, CAN-Connected Equipment, Programmable Logic and Timing.
Digital Power Converters
The STM32G431K6U3 suits digitally controlled power converters because its 170 MHz Cortex-M4F core can execute compensation calculations while advanced timers generate precision PWM drive signals. Integrated analog resources support feedback acquisition, and UART, SPI, or CANbus can connect the converter to a supervisory controller. A 32-pin UFQFPN footprint also reduces board area compared with larger leaded packages. Confirm the ADC performance, PWM timing, operating voltage, and current-sense limits in the manufacturer specifications before finalizing the control loop.
Recomendado
BLDC and PMSM Motor Control
The STM32G431K6U3 is appropriate for compact BLDC and PMSM motor controllers requiring deterministic real-time execution at 170 MHz. Its timer architecture supports PWM generation, while analog inputs can support current sensing and position feedback. Communication interfaces provide paths to encoders, sensors, and industrial controllers. The 26 available I/O pins help limit external glue logic. Firmware and external gate-driver selection must be matched to the motor voltage, current, and required switching sequence.
Recomendado
Industrial Sensor Hubs
A sensor hub built around the STM32G431K6U3 can acquire and process measurements while consolidating communications on a compact board. The 170 MHz Cortex-M4F core handles protocol processing and control logic, while I2C and SPI suit sensors and storage devices; UART, USART, and CANbus support wider system connectivity. With 32 KB of Flash, the device is best for focused firmware rather than large buffering. Use DMA for throughput-sensitive transfers and isolate analog sensor routes from switching nodes.
Recomendado
Data Acquisition Modules
The STM32G431K6U3 can serve as the control processor in a compact data-acquisition module where fast control, analog measurement, and serial transfer must coexist. Its 170 MHz core supports buffering and signal processing, and integrated ADC, timer, and DMA resources reduce component count. SPI and UART provide straightforward links to data converters or host processors. Engineer the analog front end and reference circuitry independently of the MCU, and verify acquisition bandwidth and input limits from the electrical documentation.
Recomendado
CAN-Connected Equipment
The STM32G431K6U3 fits CAN-connected industrial equipment that needs local control plus network communication. CANbus provides a dedicated path for distributed commands and diagnostics, while I2C, SPI, UART, and USART cover sensors, actuators, and service interfaces. The 170 MHz core can run control algorithms and communications concurrently, with DMA assisting data movement. Design the transceiver and bus protection separately, and validate termination, timing, and protocol-stack behavior on the target network.
Recomendado
Programmable Logic and Timing
The STM32G431K6U3 can implement programmable timing, sequencing, and monitoring functions where deterministic firmware control is preferable to fixed logic. Timers generate precise periodic events and PWM waveforms, while communications allow configuration and diagnostic access. Its floating-point Cortex-M4F core supports calculations that would otherwise require external logic or a higher-cost processor. Validate timer clock accuracy, minimum pulse widths, I/O speed, and interrupt latency before using it as a precision timing source.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para STM32G431K6U3 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | STM32G431K6T6 | STM32G431K8T6 | STM32G431K8T3 | STM32G431KBT6 |
|---|---|---|---|---|---|
| Package | 32-pin UFQFPN (5x5 mm) | 32-pin UFQFPN (5x5 mm) | 32-pin UFQFPN (5x5 mm) | 32-pin UFQFPN (5x5 mm) | 32-pin UFQFPN (5x5 mm) |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Core | Arm Cortex-M4F | Arm Cortex-M4F | Arm Cortex-M4F | Arm Cortex-M4F | Arm Cortex-M4F |
| Maximum CPU Frequency | 170 MHz | 170 MHz | 170 MHz | 170 MHz | 170 MHz |
| Flash Memory | 32 KB | 32 KB | 64 KB | 64 KB | 128 KB |
Principais diferenciais
- Higher-flash alternatives can expand firmware headroom (vs STM32G431KBT6)
- Mid-density option balances memory and package reuse (vs STM32G431K8T6)
- Direct family alternative for identical memory capacity (vs STM32G431K6T6)
Notas de projeto
Route the UFQFPN exposed pad as a thermal and ground structure according to the manufacturer land-pattern guidance. Do not treat the exposed pad as an interchangeable signal pin. Place the device-side input, output, and decoupling capacitors close to their corresponding pins, and keep sensitive analog traces away from PWM, gate-drive, and high-current return paths. A short ground connection beneath the device helps control return current and reduce analog coupling.
Plan the supply rails and decoupling around the STM32G431K6U3's internal power domains. Check the manufacturer table for operating-voltage limits, regulator configurations, startup behavior, and current consumption before connecting external analog or communications circuits. Place bulk energy storage near the power entry point and local ceramic capacitance near the MCU supply pins. Sequence any externally powered communications transceiver if the MCU and transceiver rails have different startup thresholds.
Do not approve a related STM32G431 order code solely because the package drawing matches. Confirm the exact pin-description table, Flash density, temperature marking, ordering suffix, and exposed-pad requirement. The listed alternatives retain the 170 MHz Cortex-M4F architecture but can provide 32, 64, or 128 KB of Flash. Review boot-sector layout, linker settings, firmware size, and any vendor-supported device identifiers before modifying an existing design.
Separate analog and digital return currents carefully in mixed-signal control boards. Keep ADC inputs short, use a quiet analog ground strategy where appropriate, and avoid routing sensitive inputs beneath digital clocks or PWM nets. For communications lines, follow the transceiver recommendations and provide the required termination, protection, and common-mode accommodation. Validate the finished layout with signal-integrity and EMC testing because the MCU package alone does not determine analog accuracy or bus robustness.
Informações de conformidade
Material-compliance and automotive-qualification declarations must be confirmed for the exact STM32G431K6U3 order code.
