TLV2765ID - Quad 3.6V Micro-Power RRIO Op Amp | Texas Instruments
N.º da peça: TLV2765ID ✓ AtivoTLV2765ID Visão geral
An operational amplifier is a high-gain, low-output-impedance analog building block used to amplify, buffer, filter, compare, and drive signals. The TLV2765 belongs to the micropower operational-amplifier hierarchy, combining low-voltage operation, rail-to-rail input/output capability, and a shutdown function in one quad device. Its four amplifiers make it useful when board area, supply current, and component count matter more than very high bandwidth.
The principal operating features are a 3.6 V maximum supply, 500 kHz unity-gain bandwidth, rail-to-rail inputs and outputs, approximately 20 µA typical supply current per amplifier, and a shutdown pin. These characteristics suit battery-operated instrumentation, portable sensing, low-voltage industrial measurement, and general analog signal conditioning where a 5 V supply is unavailable or undesirable.
The TLV2765 combines four rail-to-rail operational amplifiers in one SOIC-16 device. Rail-to-rail input capability keeps the usable common-mode input range close to the supply rails, while rail-to-rail output capability provides improved dynamic range when the output must approach either supply limit. The shutdown control provides a way to reduce operating current when the measured or amplified signal is not needed, although switching and output-state details should be confirmed in the manufacturer datasheet before sequencing the rails.
Typical uses include portable sensor interfaces, low-voltage transimpedance stages, active filters, battery monitoring, audio and communication signal conditioning, and general-purpose embedded analog channels. In a four-channel sensor interface, the quad organization can reduce external component count and simplify power routing. In portable equipment, the low-voltage supply and micropower operation help control energy use, while the 500 kHz bandwidth provides enough response for many low-to-moderate-frequency measurement paths.
Designers should keep input and output signal amplitudes within the linear operating region, account for output-swing limits near the supply rails, and observe the shutdown pin's required logic levels. Decoupling capacitors should be placed close to the supply pins, and sensitive analog inputs should be routed away from switching nodes and high-current return paths. Stable operation also depends on the source impedance, load, and feedback network selected for the intended gain.
This product page consolidates the TLV2765ID operating limits, package information, sourcing path, replacement considerations, and practical PCB guidance. It is intended to help engineers determine whether a low-voltage, four-amplifier SOIC solution satisfies the precision, power, and layout requirements of a new analog design.
Alternativas drop-in para TLV2765ID — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com TLV2765ID (mesmo formato e footprint) — diferindo em Operating Temperature Range, Package.
TLV2764IPWR
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
TLV2765ID Classificações máximas e características elétricas
| Amplifier Type | General-purpose operational amplifier |
| Number of Amplifiers | 4 circuits |
| Supply Voltage Range | 1.8 V to 3.6 V |
| Maximum Recommended Supply Voltage | 3.6 V |
| Unity-Gain Bandwidth | 500 kHz |
| Input Common-Mode Mode | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Typical Supply Current | 20 µA per amplifier |
| Shutdown Control | Yes |
| Supply Type | Single supply |
| Faixa de temperatura de operação | -40 °C to +85 °C |
| Encapsulamento | 16-pin SOIC, 3.9 mm wide |
| Tipo de montagem | Surface mount |
| Product Category | Instrumentation, operational amplifiers, buffer amplifiers |
Guia de Configuração de Pinos do TLV2765ID 16-pin soic, 3.9 mm wide
Configuração de pinos para TLV2765ID (pacote 16-pin soic, 3.9 mm wide). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.
Nenhum dado detalhado de pinagem disponível para TLV2765ID.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
TLV2765ID é adequado para 6 aplicaçãos: Portable Sensor Signal Conditioning, Battery Monitoring and Protection, Low-Voltage Active Filters, Industrial Low-Voltage Acquisition, Low-Power Audio and Communication Buffers, Shutdown-Enabled Measurement Channels.
Portable Sensor Signal Conditioning
The TLV2765ID fits portable sensor interfaces that operate from a 1.8 V to 3.6 V supply and need several conditioned channels. Four rail-to-rail amplifiers can buffer or amplify temperature, pressure, and resistive sensor outputs without requiring a separate amplifier for every channel. Its approximately 20 µA typical supply current per amplifier helps control consumption, while 500 kHz bandwidth comfortably covers many low-frequency sensor signals. The design trade-off is that output swing and input common-mode range approach the supply limits, so sensor headroom must be checked against the application voltage.
Recomendado
Battery Monitoring and Protection
The TLV2765ID can provide low-power comparison and buffering for battery monitoring circuits operating below 3.6 V. Its four-amplifier arrangement allows cell sensing, midpoint referencing, threshold comparison, and output buffering to be implemented with fewer external devices. Shutdown support is useful when the monitoring function is sampled periodically rather than continuously. Because the amplifiers operate rail-to-rail, cell measurements near the supply extremes remain useful, although designers should preserve output margin and confirm the exact common-mode and shutdown limits in the family datasheet.
Recomendado
Low-Voltage Active Filters
The TLV2765ID is suitable for active filtering in portable and embedded measurement systems where a 3.6 V maximum supply limits available signal swing. Its 500 kHz unity-gain bandwidth allows the amplifiers to implement low-frequency filters with useful closed-loop bandwidth and phase margin when configured with suitable external resistors and capacitors. Multiple amplifier sections can form a second- or fourth-order response on one board. Component tolerances, capacitor types, and the amplifier's gain-bandwidth behavior should be evaluated during simulation to avoid unexpected gain peaking near the filter cutoff.
Recomendado
Industrial Low-Voltage Acquisition
The TLV2765ID can condition low-level signals in compact industrial acquisition modules powered from a 3.3 V rail. Rail-to-rail input and output operation helps preserve signal range when transducer outputs are referenced near ground or near the positive supply, while four channels reduce the number of amplifiers needed for a multichannel front end. The 500 kHz bandwidth is appropriate for many sensor and control signals rather than high-speed instrumentation. Layout should include close decoupling, guarded input routing, and separation from motors, relays, and switching regulators.
Recomendado
Low-Power Audio and Communication Buffers
The TLV2765ID can provide low-level audio or communication-signal buffering when the system supply is limited to 3.6 V. Four rail-to-rail channels support input coupling, gain stages, mixers, and output drivers within a compact package. The 500 kHz bandwidth covers a substantial portion of the audible range and many low-speed communication signals, while the micropower operating current is advantageous in portable equipment. Designers should check output-current capability into the actual load and account for the output-swing limit rather than treating the output as an unrestricted rail-to-rail driver.
Recomendado
Shutdown-Enabled Measurement Channels
The TLV2765ID fits measurement systems that periodically enable and disable analog channels to reduce power consumption. Shutdown can remove amplifiers from the active state during idle periods, while the integrated quad architecture supports several independent channels on one 16-pin SOIC. This arrangement is useful in handheld analyzers, environmental monitors, and embedded diagnostic equipment. The system should include an unambiguous shutdown logic level and account for startup time, output settling, and any state present on the amplifier outputs while disabled.
Recomendado
Dados de referência de engenharia para TLV2765ID — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | TLV2764IPWR |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 16-pin SOIC | 16-pin SOIC |
| Number of Amplifiers | 4 circuits | 4 circuits |
| Supply Voltage Range | 1.8 V to 3.6 V | 1.8 V to 3.6 V |
| Maximum Supply Voltage | 3.6 V | 3.6 V |
| Input Common-Mode Mode | Rail-to-rail | Rail-to-rail |
| Output Swing | Rail-to-rail | Rail-to-rail |
| Shutdown Control | Yes | Yes |
Principais diferenciais
- Four low-power amplifiers in one SOIC package (vs TLV2764IPWR)
- 500 kHz bandwidth for the target family (vs TLV2764IPWR)
- Rail-to-rail input and output operation (vs TLV2764IPWR)
Notas de projeto
Place the recommended decoupling capacitors directly beside the TLV2765ID supply and ground pins, using short traces and a compact ground return. Keep the feedback components close to their associated amplifier pins to minimize parasitic coupling. Route input and feedback nets away from switching converters, relay contacts, and high-current output paths. This is especially important in portable and industrial systems where the device may operate near its 1.8 V lower supply limit.
Confirm the complete power budget when using all four amplifier channels. With approximately 20 µA typical supply current per amplifier, the four amplifiers contribute about 80 µA under the typical condition, before shutdown-state overhead, bias currents, and external circuitry. Use the shutdown input during long idle periods and validate startup and settling time before sampling immediately after enabling the device.
Rail-to-rail input and output operation does not guarantee distortion-free operation arbitrarily close to the supply rails. Preserve the specified input common-mode and output-swing margins, especially in sensor dividers or battery-powered measurements where the signal may approach 0 V or 3.6 V. For low-frequency precision work, evaluate input offset, bias-current error, and source impedance using the manufacturer characterization curves rather than relying only on the nominal rail-to-rail description.
Do not treat the family relationship between TLV2764 and TLV2765 as proof of identical behavior. Compare the complete pin descriptions, gain-bandwidth product, output-swing limits, shutdown response, and electrical characteristics before using either device in the same design. Also avoid extending the TLV2765ID supply beyond its 3.6 V maximum recommended voltage, particularly during transients or supply ramp conditions.
Informações de conformidade
The manufacturer identifies the TLV2765 as an industrial-temperature family, but no explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was captured. These fields remain unknown rather than inferred from the general-purpose product classification.