Texas Instruments

TLV2765ID - Quad 3.6V Micro-Power RRIO Op Amp | Texas Instruments

MPN: TLV2765ID ✓ Hoạt động
1.8 V to 3.6 V Vdss 20 µA per amplifier Id 16-pin SOIC, 3.9 mm wide Package
MOQ: 1 |

TLV2765ID Tóm tắt

Texas Instruments TLV2765ID is a quad, general-purpose operational amplifier with rail-to-rail input and output operation, a 3.6 V maximum supply, 500 kHz gain-bandwidth product, and shutdown support, all in a 16-pin SOIC package. It operates from 1.8 V to 3.6 V and supports low-voltage, low-power signal-chain designs requiring four amplifiers in one package.

An operational amplifier is a high-gain, low-output-impedance analog building block used to amplify, buffer, filter, compare, and drive signals. The TLV2765 belongs to the micropower operational-amplifier hierarchy, combining low-voltage operation, rail-to-rail input/output capability, and a shutdown function in one quad device. Its four amplifiers make it useful when board area, supply current, and component count matter more than very high bandwidth.

The principal operating features are a 3.6 V maximum supply, 500 kHz unity-gain bandwidth, rail-to-rail inputs and outputs, approximately 20 µA typical supply current per amplifier, and a shutdown pin. These characteristics suit battery-operated instrumentation, portable sensing, low-voltage industrial measurement, and general analog signal conditioning where a 5 V supply is unavailable or undesirable.

The TLV2765 combines four rail-to-rail operational amplifiers in one SOIC-16 device. Rail-to-rail input capability keeps the usable common-mode input range close to the supply rails, while rail-to-rail output capability provides improved dynamic range when the output must approach either supply limit. The shutdown control provides a way to reduce operating current when the measured or amplified signal is not needed, although switching and output-state details should be confirmed in the manufacturer datasheet before sequencing the rails.

Typical uses include portable sensor interfaces, low-voltage transimpedance stages, active filters, battery monitoring, audio and communication signal conditioning, and general-purpose embedded analog channels. In a four-channel sensor interface, the quad organization can reduce external component count and simplify power routing. In portable equipment, the low-voltage supply and micropower operation help control energy use, while the 500 kHz bandwidth provides enough response for many low-to-moderate-frequency measurement paths.

Designers should keep input and output signal amplitudes within the linear operating region, account for output-swing limits near the supply rails, and observe the shutdown pin's required logic levels. Decoupling capacitors should be placed close to the supply pins, and sensitive analog inputs should be routed away from switching nodes and high-current return paths. Stable operation also depends on the source impedance, load, and feedback network selected for the intended gain.

This product page consolidates the TLV2765ID operating limits, package information, sourcing path, replacement considerations, and practical PCB guidance. It is intended to help engineers determine whether a low-voltage, four-amplifier SOIC solution satisfies the precision, power, and layout requirements of a new analog design.

Bộ thay thế dễ dàng lắp đặt cho TLV2765ID — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Các biến thể trong loạt này

Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với TLV2765ID (cùng hình factor và footprint) — khác nhau ở Operating Temperature Range, Package.

Texas Instruments
Operating Temperature Range: 0 C to +70 C
Package: 16-pin SOIC
So sánh với TLV2765ID →

TLV2764IPWR

✅ Drop-In ⚠️ Thông số chưa được xác minh
📦 16-pin SOIC
Same TLV276x quad SOIC-16 family and 1.8 V to 3.6 V supply class; individual bandwidth and electrical characteristics require confirmation against the TLV2765ID

📋 Tham chiếu thay thế (không có trong danh mục)

TLV2765ID Tỷ lệ tối đa & tính chất điện

Amplifier Type General-purpose operational amplifier
Number of Amplifiers 4 circuits
Supply Voltage Range 1.8 V to 3.6 V
Maximum Recommended Supply Voltage 3.6 V
Unity-Gain Bandwidth 500 kHz
Input Common-Mode Mode Rail-to-rail
Output Swing Rail-to-rail
Typical Supply Current 20 µA per amplifier
Shutdown Control Yes
Supply Type Single supply
Khoảng nhiệt độ hoạt động -40 °C to +85 °C
Hộp 16-pin SOIC, 3.9 mm wide
Kiểu lắp đặt Surface mount
Product Category Instrumentation, operational amplifiers, buffer amplifiers

Hướng dẫn cấu hình chân TLV2765ID 16-pin soic, 3.9 mm wide

Cấu hình chân cho TLV2765ID (16-pin soic, 3.9 mm wide gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.

Bảng cấu hình chân 16-pin soic, 3.9 mm wide cho TLV2765ID

Không có dữ liệu chân cụ thể sẵn có cho TLV2765ID.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

TLV2765ID phù hợp cho 6 Áp dụngs: Portable Sensor Signal Conditioning, Battery Monitoring and Protection, Low-Voltage Active Filters, Industrial Low-Voltage Acquisition, Low-Power Audio and Communication Buffers, Shutdown-Enabled Measurement Channels.

📱

Portable Sensor Signal Conditioning

The TLV2765ID fits portable sensor interfaces that operate from a 1.8 V to 3.6 V supply and need several conditioned channels. Four rail-to-rail amplifiers can buffer or amplify temperature, pressure, and resistive sensor outputs without requiring a separate amplifier for every channel. Its approximately 20 µA typical supply current per amplifier helps control consumption, while 500 kHz bandwidth comfortably covers many low-frequency sensor signals. The design trade-off is that output swing and input common-mode range approach the supply limits, so sensor headroom must be checked against the application voltage.

⚡

Battery Monitoring and Protection

The TLV2765ID can provide low-power comparison and buffering for battery monitoring circuits operating below 3.6 V. Its four-amplifier arrangement allows cell sensing, midpoint referencing, threshold comparison, and output buffering to be implemented with fewer external devices. Shutdown support is useful when the monitoring function is sampled periodically rather than continuously. Because the amplifiers operate rail-to-rail, cell measurements near the supply extremes remain useful, although designers should preserve output margin and confirm the exact common-mode and shutdown limits in the family datasheet.

🔧

Low-Voltage Active Filters

The TLV2765ID is suitable for active filtering in portable and embedded measurement systems where a 3.6 V maximum supply limits available signal swing. Its 500 kHz unity-gain bandwidth allows the amplifiers to implement low-frequency filters with useful closed-loop bandwidth and phase margin when configured with suitable external resistors and capacitors. Multiple amplifier sections can form a second- or fourth-order response on one board. Component tolerances, capacitor types, and the amplifier's gain-bandwidth behavior should be evaluated during simulation to avoid unexpected gain peaking near the filter cutoff.

🏭

Industrial Low-Voltage Acquisition

The TLV2765ID can condition low-level signals in compact industrial acquisition modules powered from a 3.3 V rail. Rail-to-rail input and output operation helps preserve signal range when transducer outputs are referenced near ground or near the positive supply, while four channels reduce the number of amplifiers needed for a multichannel front end. The 500 kHz bandwidth is appropriate for many sensor and control signals rather than high-speed instrumentation. Layout should include close decoupling, guarded input routing, and separation from motors, relays, and switching regulators.

🎧

Low-Power Audio and Communication Buffers

The TLV2765ID can provide low-level audio or communication-signal buffering when the system supply is limited to 3.6 V. Four rail-to-rail channels support input coupling, gain stages, mixers, and output drivers within a compact package. The 500 kHz bandwidth covers a substantial portion of the audible range and many low-speed communication signals, while the micropower operating current is advantageous in portable equipment. Designers should check output-current capability into the actual load and account for the output-swing limit rather than treating the output as an unrestricted rail-to-rail driver.

🧩

Shutdown-Enabled Measurement Channels

The TLV2765ID fits measurement systems that periodically enable and disable analog channels to reduce power consumption. Shutdown can remove amplifiers from the active state during idle periods, while the integrated quad architecture supports several independent channels on one 16-pin SOIC. This arrangement is useful in handheld analyzers, environmental monitors, and embedded diagnostic equipment. The system should include an unambiguous shutdown logic level and account for startup time, output settling, and any state present on the amplifier outputs while disabled.

What is the TLV2765ID?
The TLV2765ID is a Texas Instruments quad operational amplifier designed for low-voltage, low-power analog signal conditioning. It combines four rail-to-rail input/output amplifiers, 500 kHz bandwidth, and shutdown control in a 16-pin SOIC package. According to the manufacturer product page, the family operates from 1.8 V to 3.6 V, making it appropriate for battery-powered and low-voltage embedded systems.
What is the operating voltage of TLV2765ID?
The TLV2765ID operates from 1.8 V to 3.6 V with a single supply. The Texas Instruments TLV2760 family datasheet identifies 3.6 V as the maximum recommended supply voltage and describes operation down to 1.8 V. This range supports two-cell and low-voltage portable systems, although the total input and output voltage limits must remain within the device specifications.
What are the key specifications of TLV2765ID that engineers should know?
The TLV2765ID provides four amplifiers, 500 kHz unity-gain bandwidth, rail-to-rail input and output capability, and approximately 20 µA typical supply current per amplifier in a 16-pin SOIC package. The Texas Instruments family documentation also identifies 1.8 V to 3.6 V operation, single-supply use, and shutdown support. Input offset, bias current, slew rate, and output-current limits should be taken from the detailed manufacturer datasheet.
Does the TLV2765ID support rail-to-rail input and output?
Yes, the TLV2765ID supports rail-to-rail input and output operation. Texas Instruments describes the TLV2765 as a rail-to-rail input/output operational amplifier family. Rail-to-rail input operation is useful when sensor or divider voltages approach the supply limits, while rail-to-rail output operation improves signal range. Designers must still observe the specified output-swing limits and keep the output in its linear region.
Why does the TLV2765ID include a shutdown function?
The shutdown function allows the TLV2765ID to reduce its operating current when amplification is temporarily unnecessary. Texas Instruments identifies shutdown as a defining feature of the TLV2765 family. It is particularly useful in portable instruments and duty-cycled sensing systems, where maintaining four active amplifiers would waste energy. The required logic levels and behavior of each amplifier output during shutdown should be confirmed in the manufacturer datasheet.
Where can I download the TLV2765ID datasheet PDF?
The official TLV2765 family datasheet can be downloaded from the Texas Instruments document link on this page, and the TLV2765 product page provides ordering and technical information. The family datasheet covers the electrical characteristics, shutdown behavior, pin configuration, and application information for TLV2765ID. Use the ordering table to confirm that the SOIC-16 suffix matches the required temperature range and reel configuration.
Where can I find the TLV2765ID pinout?
The TLV2765ID pin configuration is shown in the pin-configuration section of the Texas Instruments TLV2760 family datasheet. The device uses a 16-pin SOIC package containing four rail-to-rail operational amplifiers and their shutdown-related connections. Assign PCB nets from that manufacturer diagram, including supply pins, non-inverting and inverting inputs, amplifier outputs, and shutdown control.
What can replace the TLV2765ID?
A valid replacement must use the same 16-pin SOIC footprint, preserve the four-amplifier pin arrangement, and remain within about 30% of the key voltage, bandwidth, and current ratings. The TLV2764IPWR is the closest same-family candidate identified, but engineers should verify its pinout and shutdown behavior against the TLV2765ID before approving it as a drop-in replacement. No cross-brand equivalent was established from the available cross-reference information.
Is the TLV2764IPWR a drop-in replacement for the TLV2765ID?
The TLV2764IPWR is a same-manufacturer, same-family candidate that uses the 16-pin SOIC format and is provisionally treated as pin-compatible with the TLV2765ID. However, its individual input, output, bandwidth, and shutdown characteristics must be checked against the exact TLV2765ID operating requirements. This comparison is a family-level assessment rather than a manufacturer-published drop-in guarantee.
What is the best cross-brand equivalent for the TLV2765ID?
No cross-brand drop-in equivalent was confirmed for the TLV2765ID from the available component cross-reference information. A suitable substitute must provide four rail-to-rail amplifiers in the same 16-pin SOIC pinout while meeting the 1.8 V to 3.6 V supply range, 500 kHz bandwidth requirement, shutdown behavior, and current limits of the application. Use the manufacturer's pin and electrical tables before treating any cross-brand part as interchangeable.
TLV2765ID vs TLV2764IPWR: which is better for a low-voltage sensor interface?
Choose the TLV2765ID when its 500 kHz bandwidth and documented shutdown behavior satisfy the sensor interface. Consider the TLV2764IPWR only after confirming that its bandwidth, common-mode range, output swing, and shutdown response remain acceptable. Both use the same 16-pin SOIC family format, so the decision should be based on verified electrical differences rather than package appearance alone.
When should I choose the TLV2765ID over a lower-bandwidth quad op amp?
Choose the TLV2765ID when a low-voltage sensor signal requires more than 500 kHz unity-gain bandwidth, rail-to-rail input and output operation, and integrated shutdown. A lower-bandwidth amplifier may be appropriate for slower filtering or buffering and could offer different power or accuracy trade-offs. Verify gain-bandwidth, output-swing, noise, and shutdown requirements against the signal bandwidth and operating supply.
Is the TLV2765ID suitable for battery-powered instrumentation?
The TLV2765ID is well suited to battery-powered instrumentation because it supports 1.8 V to 3.6 V single-supply operation and draws approximately 20 µA per amplifier in the typical condition stated for the family. Four integrated channels also reduce component count. The shutdown input can further reduce consumption during idle intervals, while total battery life still depends on sensor current, duty cycle, and regulator efficiency.
How should decoupling be designed for the TLV2765ID?
Place the required supply-decoupling capacitors close to the TLV2765ID power pins, with the shortest possible ground return and no long loops through the analog area. The Texas Instruments family datasheet should be used for the recommended capacitor values and layout. Keep sensitive input and feedback traces away from switching nodes, and provide a low-impedance ground reference because input bias current and supply noise can otherwise affect measurement accuracy.
Where can I buy the TLV2765ID and what is its lead time?
Use the Request a Quote form on this page to request the current TLV2765ID price, stock position, minimum order quantity, and production lead time. Commercial terms can change with market conditions and order quantity, so the form is the appropriate route for a current commitment. The ordering information on the Texas Instruments product page can be used to confirm supported package and temperature options.

Dữ liệu tham khảo kỹ thuật cho TLV2765ID — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose the TLV2765ID for a low-voltage design that needs four general-purpose, rail-to-rail amplifiers with 500 kHz bandwidth and shutdown control in a 16-pin SOIC package. It is especially appropriate for portable sensing, battery monitoring, low-voltage acquisition, and compact active-filter circuits where the 1.8 V to 3.6 V supply range and micropower operation are important. The TLV2764IPWR may be considered for a similar low-voltage quad-amplifier design, but its pin descriptions, bandwidth, supply current, and shutdown behavior should be compared with the TLV2765ID before release. No cross-brand drop-in replacement was confirmed. If a candidate uses another package, has a different shutdown connection, or differs in common-mode range, it requires PCB redesign rather than drop-in substitution.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này TLV2764IPWR
Brand Texas Instruments Texas Instruments
Package 16-pin SOIC 16-pin SOIC
Number of Amplifiers 4 circuits 4 circuits
Supply Voltage Range 1.8 V to 3.6 V 1.8 V to 3.6 V
Maximum Supply Voltage 3.6 V 3.6 V
Input Common-Mode Mode Rail-to-rail Rail-to-rail
Output Swing Rail-to-rail Rail-to-rail
Shutdown Control Yes Yes

Bảo phân biệt quan trọng

  • Four low-power amplifiers in one SOIC package (vsTLV2764IPWR)
  • 500 kHz bandwidth for the target family (vsTLV2764IPWR)
  • Rail-to-rail input and output operation (vsTLV2764IPWR)

Ghi chú thiết kế

Place the recommended decoupling capacitors directly beside the TLV2765ID supply and ground pins, using short traces and a compact ground return. Keep the feedback components close to their associated amplifier pins to minimize parasitic coupling. Route input and feedback nets away from switching converters, relay contacts, and high-current output paths. This is especially important in portable and industrial systems where the device may operate near its 1.8 V lower supply limit.

Confirm the complete power budget when using all four amplifier channels. With approximately 20 µA typical supply current per amplifier, the four amplifiers contribute about 80 µA under the typical condition, before shutdown-state overhead, bias currents, and external circuitry. Use the shutdown input during long idle periods and validate startup and settling time before sampling immediately after enabling the device.

Rail-to-rail input and output operation does not guarantee distortion-free operation arbitrarily close to the supply rails. Preserve the specified input common-mode and output-swing margins, especially in sensor dividers or battery-powered measurements where the signal may approach 0 V or 3.6 V. For low-frequency precision work, evaluate input offset, bias-current error, and source impedance using the manufacturer characterization curves rather than relying only on the nominal rail-to-rail description.

Do not treat the family relationship between TLV2764 and TLV2765 as proof of identical behavior. Compare the complete pin descriptions, gain-bandwidth product, output-swing limits, shutdown response, and electrical characteristics before using either device in the same design. Also avoid extending the TLV2765ID supply beyond its 3.6 V maximum recommended voltage, particularly during transients or supply ramp conditions.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

The manufacturer identifies the TLV2765 as an industrial-temperature family, but no explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was captured. These fields remain unknown rather than inferred from the general-purpose product classification.

Dữ liệu được xác minh vào: 2026-11-19 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

TLV2765ID datasheet TLV2765ID pinout TLV2765ID datasheet pdf TLV2765ID SOIC-16 TLV2765ID 500kHz amplifier TLV2765ID 3.6V supply TLV2765ID shutdown TLV2765ID equivalent TLV2765ID replacement TLV2765ID vs TLV2764IPWR TLV2765ID price TLV2765ID stock Texas Instruments TLV2765ID TLV2765ID battery sensor interface TLV2765ID shutdown application circuit

Các bộ phận và thuật ngữ liên quan

Texas Instruments TLV2765ID TLV2765 TLV2764IPWR quad operational amplifier operational amplifier micro-power operational amplifier low-dropout analog IC signal-conditioning IC semiconductor rail-to-rail input rail-to-rail output shutdown control single-supply operation unity-gain bandwidth supply current common-mode input range output swing SOIC-16 surface-mount package sensor interface battery monitoring active filter industrial instrumentation low-voltage analog
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ