TLV2771CD - 5.1MHz High-Slew-Rate Op Amp | Texas Instruments
N.º da peça: TLV2771CD ✓ AtivoTLV2771CD Visão geral
An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. As a voltage-feedback amplifier, it belongs to the broader hierarchy of amplifier ICs, instrumentation amplifiers, analog signal-processing ICs, and semiconductors. Its high gain and negative-feedback operation make it useful for sensor interfaces, waveform conditioning, active filters, and low-level signal amplification where signal integrity and response speed are important.
The principal performance features are the 5.1 MHz gain-bandwidth product, 10.5 V/µs slew rate, and rail-to-rail output. These characteristics allow the amplifier to reproduce fast-moving waveforms with less distortion than lower-bandwidth general-purpose amplifiers. A 5.5 V maximum supply voltage also supports compact systems operating below 6 V, while the single-amplifier configuration avoids the space and power requirements of a dual or quad device when only one signal path is needed.
Technologically, the TLV2771CD combines CMOS-compatible low-power operation with high-speed, high-output-drive characteristics. The 10.5 V/µs slew rate is particularly useful when driving finite-capacitance loads or following sensor and comparator outputs. Rail-to-rail output maximizes usable signal range at the load, although input common-mode range, output-current behavior, input-bias current, noise, and offset specifications should be checked against the exact circuit requirements before finalizing a precision design.
Typical uses include sensor-signal conditioning, buffered data acquisition, active analog filtering, communications-interface support, and industrial control or test equipment. It is particularly suitable when a design needs more bandwidth than a general-purpose micropower amplifier but does not require the very low noise or precision offset of a specialized instrumentation amplifier. One amplifier per package also supports designs with isolated signal paths or low channel counts.
For PCB implementation, use the manufacturer’s recommended SOIC-8 land pattern, place decoupling close to the supply pins, and avoid long return paths beneath sensitive input nodes. Check output swing, load capacitance, and stability requirements against the operating voltage. Because the SOIC package has exposed lead geometry and limited heat-dissipation area, use appropriate copper spreading and temperature-rise analysis when driving sustained heavy loads.
This page combines the TLV2771CD’s core electrical characteristics with focused application guidance, package considerations, drop-in alternatives, and a parameter-by-parameter comparison. These engineering-oriented details help determine whether the amplifier’s 5.1 MHz bandwidth, 10.5 V/µs slew rate, and 5.5 V supply limit align with the target analog signal chain before layout and prototype work begin.
Alternativas drop-in para TLV2771CD — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com TLV2771CD (mesmo formato e footprint) — diferindo em Package, Shutdown Function, Slew Rate.
TLV2771ID
✅ Drop-InConsulte o preço
Ver ficha técnica →TLV2771AID
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
TLV2771QD
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
TLV2772AID
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
TLV2774AIP
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
TLV2771CD Classificações máximas e características elétricas
| Product Type | Single operational amplifier |
| Maximum Supply Voltage | 5.5 V |
| Minimum Supply Voltage | 2.7 V |
| Gain-Bandwidth Product | 5.1 MHz |
| Slew Rate | 10.5 V/µs |
| Output Topology | Rail-to-rail output |
| Number of Circuits | 1 circuit |
| Encapsulamento | 8-pin SOIC, 3.9 mm nominal body width |
| Tipo de montagem | Surface mount |
| Product Classification | General-purpose amplifier |
| Shutdown Function | Not specified for TLV2771; family shutdown variants exist |
Guia de Configuração de Pinos do TLV2771CD 8-pin soic, 3.9 mm nominal body width
Configuração de pinos para TLV2771CD (pacote 8-pin soic, 3.9 mm nominal body width). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.
Nenhum dado detalhado de pinagem disponível para TLV2771CD.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
TLV2771CD é adequado para 6 aplicaçãos: Industrial Sensor Signal Conditioning, Precision Active Filtering, Data Acquisition Buffering, Communications Interface Support, Battery-Powered Portable Equipment, Test and Measurement Buffer.
Industrial Sensor Signal Conditioning
The TLV2771CD fits industrial sensor interfaces that require faster response than a conventional general-purpose amplifier. Its 5.1 MHz gain-bandwidth product and 10.5 V/µs slew rate can preserve the timing and amplitude of rapidly changing sensor signals while operating from a 2.7 V to 5.5 V supply. Place the amplifier between the sensor and an ADC or controller, and confirm that the input common-mode range covers the sensor’s full output range. The rail-to-rail output helps maximize available signal span in low-voltage equipment. Its single-amplifier SOIC-8 package also conserves board area where only one conditioned channel is required.
Recomendado
Precision Active Filtering
The TLV2771CD is suitable for active filter stages requiring more bandwidth than a micropower amplifier. A 5.1 MHz gain-bandwidth product provides useful closed-loop bandwidth for low- to moderate-order filters, while the 10.5 V/µs slew rate helps maintain low large-signal distortion when processing high-frequency components. The single 2.7 V to 5.5 V supply simplifies portable and embedded analog systems. Component values should be calculated from the required cutoff, gain, and Q, and the amplifier’s exact noise, offset, and stability characteristics should be checked against the filter’s noise and phase requirements.
Recomendado
Data Acquisition Buffering
The TLV2771CD can buffer sensor outputs before multiplexers, sample-and-hold stages, or analog-to-digital converters. Its 5.1 MHz gain-bandwidth product and 10.5 V/µs slew rate reduce the risk of excessive settling time when driving the input capacitance of a successive-approximation ADC. Operating from 2.7 V to 5.5 V also supports common embedded acquisition rails. Confirm ADC acquisition time and input capacitance against the amplifier’s output-drive and stability limits. A low-noise decoupling arrangement and a short, protected route from the sensor are important for preserving measurement fidelity.
Recomendado
Communications Interface Support
The TLV2771CD is appropriate for communications equipment that needs to buffer line-level or differential signals into a downstream converter. Its 10.5 V/µs slew rate supports faster transitions than basic general-purpose amplifiers, while the 5.1 MHz gain-bandwidth product is useful for moderate-bandwidth signal conditioning. The rail-to-rail output can improve useable swing in a 5 V signal chain. For high-speed links, verify that the required data rate, settling time, capacitive loading, common-mode range, and output-current capability meet the communications standard before using this device.
Recomendado
Battery-Powered Portable Equipment
The TLV2771CD can be used in compact battery-powered equipment requiring a rail-to-rail output amplifier with modest supply requirements. Its minimum operating voltage of 2.7 V supports 3.3 V systems, and its 5.5 V maximum provides compatibility with 5 V rails. The single-amplifier configuration avoids the board area of a multi-amplifier package when only one conditioning channel is required. For portable designs, confirm standby-current requirements, output loading, input bias current, and shutdown requirements; if the amplifier must remain active during battery sleep periods, a micropower device may be more appropriate.
Recomendado
Test and Measurement Buffer
The TLV2771CD is useful as a general-purpose buffer in compact test and measurement equipment. The 5.1 MHz gain-bandwidth product supports moderate-frequency signal acquisition, while the 10.5 V/µs slew rate produces faster large-signal transitions than low-bandwidth precision amplifiers. Its 8-pin SOIC package simplifies assembly and replacement, and its rail-to-rail output can preserve signal amplitude at low supply voltages. Validate the complete measurement path for source impedance, probe capacitance, input offset, noise, and settling behavior. A shield or guard structure may be needed when the source has high impedance and leakage can bias the measurement.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para TLV2771CD — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | TLV2771ID | TLV2771AID | TLV2771QD | TLV2772AID | TLV2774AIP |
|---|---|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Maximum Supply Voltage | 5.5 V | 5.5 V | 5.5 V | 5.5 V | 5.5 V | 5.5 V |
| Minimum Supply Voltage | 2.7 V | 2.7 V | 2.7 V | 2.7 V | 2.7 V | 2.7 V |
| Output Topology | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output |
Principais diferenciais
- Combines moderate bandwidth with a high slew rate (vs TLV2771AID)
- Supports low-voltage, high-speed signal conditioning (vs TLV2772AID)
- Commercial-grade option in a standard SOIC footprint (vs TLV2771ID)
Notas de projeto
Use the manufacturer’s 8-pin SOIC land pattern and place the input, output, and supply decoupling components close to their associated pins. Keep the ground return short and continuous, avoid routing sensitive input traces beneath the package, and separate analog input routing from clocks, switching-node copper, and other high-energy paths. The rail-to-rail output improves signal range, but it does not remove the need for careful analog grounding.
Do not assume that the 5.1 MHz gain-bandwidth product permits 5.1 MHz operation at every closed-loop gain. The usable bandwidth, phase margin, and output swing depend on the selected gain, noise gain, load capacitance, and supply voltage. Likewise, the 10.5 V/µs slew rate describes the maximum output transition rate rather than guaranteed bandwidth. Use the manufacturer’s stability and load-capacitance guidance before driving ADC inputs, long cables, or large capacitive loads.
Keep the supply within the device’s 2.7 V to 5.5 V operating limits and account for supply noise, startup transients, and input-signal excursions that may approach the rails. Add local bypass capacitance to suppress supply ripple, especially when the amplifier follows a switching converter. For low-power designs, compare the operating current at the selected signal level because a high-speed amplifier may consume more power than a micropower precision device.
For instrumentation applications, verify input offset, input bias current, noise, common-mode range, and output-current capability against the source and load. A high-impedance sensor can require guarding or a bias resistor to control input bias-induced error. If the output drives a sampling ADC, check settling time for the selected closed-loop gain and consider a small isolation resistor when capacitive loading could impair stability.
Informações de conformidade
The TLV2771 is a general-purpose commercial operational amplifier and is not an automotive-qualified AEC-Q100 device. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the current manufacturer product documentation.